Skip to content
From Fire Safety Academy Wiki
Contents
  1. 1Access, escape and the meaning of limited openings
  2. 2Smoke removal, boundaries and operational assumptions
  3. 3Objectives and protected spaces
  4. 4System interaction and reliability
  5. 5Commissioning and design limits
  6. 6What the system is intended to protect
  7. 7Purpose and route continuity
  8. 8Engineering evaluation
  9. 9See also
  10. 10Notes
  11. 11References

Underground and windowless structures are buildings or building portions whose position or restricted external openings complicate escape, smoke removal and emergency access. The Society of Fire Protection Engineers (SFPE) Handbook's smoke-management principles distinguish protection of escape routes from extraction within the fire space. That distinction is especially relevant where natural openings and alternative access points are limited.[1][2]

The National Fire Protection Association (NFPA) Fire Protection Handbook uses the later term limited-access structure in its account of the NFPA framework. Classification depends on the emergency openings available, rather than appearance alone. A building that looks windowless may still contain qualifying access panels, while an underground arrangement introduces its own geometric limitations.[3]

Means of escape, smoke control and fire service access must therefore be assessed together with the occupancy. The special structure does not remove the requirements associated with its use. Instead, the limited openings and access routes create additional conditions that the fire-safety strategy must address.[2]

Access, escape and the meaning of limited openings

External openings provide several possible functions, including entry for responders and ventilation; the NFPA handbook explains that fewer openings can restrict those functions and delay assessment from outside. A responding crew may have less information about the fire location before entering. The building's access arrangement is therefore part of the incident conditions.[4]

Underground and windowless structures: access, escape and the meaning of limited openings, showing the relationships described in the text.
Access, escape and the meaning of limited openings in the assessment of Underground and windowless structures.

The historical limited-access definition concerns the absence of suitable emergency openings. The handbook describes access panels that can be recognised and opened from both sides; their size, location and distribution determine whether they meet the relevant provisions. A small service opening or an inaccessible glazed panel should not be counted merely because it penetrates the external wall.[3]

Underground construction can direct occupants and responders towards a limited number of vertical connections; the complete escape arrangement includes those connections and the space receiving people above ground. A route should be assessed through to its final destination. Leaving the underground room does not end the assessment if the next corridor or stair remains exposed.[3][5]

Natural illumination may be limited or absent. The NFPA handbook identifies this as relevant to escape and emergency operations; the intended lighting and identification of routes must therefore remain available under the incident conditions. The broader escape assessment includes the dependencies that allow people to find and use the route.[4][6]

The Life Safety Code discussion in the 2008 handbook combines occupancy provisions with special-structure provisions; it also describes a performance-based option within that historical framework. The designer, owner and authority need a common statement of objectives and assumptions. The assessment should identify both the ordinary occupancy hazards and the added restrictions of the structure.[7]

A tunnel fire shares some concerns about confinement and access, but tunnel geometry and operation create their own design problem. The label underground should not make every building equivalent to a transport tunnel. The NFPA special-structure approach requires attention to the actual occupancy and construction, while the smoke analysis must represent the real flow paths.[2][8]

Smoke removal, boundaries and operational assumptions

Smoke and heat exhaust ventilation can provide a planned path for removing combustion products. In a limited-access building, the NFPA handbook notes dependence on mechanical systems and door openings when other openings are absent. The arrangement should therefore define both extraction and the air entering to replace it. An exhaust fan cannot be assessed independently of those paths.[4][9]

Underground and windowless structures: smoke removal, boundaries and operational assumptions, showing the relationships described in the text.
Smoke removal, boundaries and operational assumptions in the assessment of Underground and windowless structures.

The objective determines the space and duration to be protected. Keeping a stair available differs from keeping the entire fire compartment clear of smoke; the International Fire Engineering Guidelines identify extraction, pressurisation, containment and other approaches. The selected method should match the compartmentation and occupied locations instead of relying on a generic claim of smoke removal.[10]

Smoke can pass through doors, shafts and service routes connecting the underground area to the rest of the building. Pressure differences affect those flows. A ventilation change can therefore alter conditions beyond the room containing the fire. The assessment must include the relevant boundaries and openings when judging the performance of an active system.[10]

Fire location and occupancy influence whether ventilation supports the intended response; the NFPA handbook expressly connects ventilation feasibility with the nature and scale of the occupancy. The number of people, the available routes and the expected fire development all affect the required outcome. A system suitable for one use may need reassessment when that use changes.[4]

The operating sequence needs to identify detection, fan and damper states, and the interfaces with other building services. The International Fire Engineering Guidelines connect the design with management and maintenance. These dependencies are particularly visible where the strategy relies on mechanical operation because natural access and ventilation are restricted.[11]

Objectives and protected spaces

The 2005 International Fire Engineering Guidelines (IFEG) describe the general objective as removing heat and minimising smoke concentration in designated areas. This focuses attention on selected locations rather than an undefined whole-building outcome. The relevant locations might include escape routes, occupied zones or areas needed for firefighting.[12]

Cooper identifies three objectives for designed smoke and heat venting. These are supporting escape, helping firefighters enter and see the fire, and reducing smoke and heat damage to property. A system may address more than one objective, but the corresponding conditions and duration must be made explicit.[13]

A smoke-control zone provides a defined boundary for that objective. It can be separated from adjacent zones by partitions, floors, doors and dampers. NUREG-1805 notes that a smoke compartment is enclosed on all sides, including the top and bottom.[14]

Protection of a boundary is not the same as maintaining clear air throughout the fire room. Pressurisation can restrict smoke entering a stair while leaving severe conditions in the fire compartment. The location of people and the intended place of safety determine whether that outcome is useful.[15]

Extraction has a different spatial aim. It removes smoke from the hot layer to slow descent or reduce concentration in the protected volume. Its effectiveness depends on the incoming smoke flow and replacement air, so a rated fan capacity alone cannot specify the resulting layer height.[16][17]

System interaction and reliability

Smoke control often relies on detection to select the correct fire mode. Zone systems may need the alarm location as well as confirmation that a fire exists. An incorrect zone signal could produce pressure or airflow patterns that do not match the fire location.[18]

Sprinkler operation can reduce heat and buoyancy while disturbing the smoke layer. The US National Institute of Standards and Technology (NIST) describes cooling and mixing in its discussion of building smoke management. This interaction can change the conditions assumed for smoke transport and heat-operated vents.[15]

Cooper describes delayed activation of later sprinklers or vents when earlier sprays cool their elements. Such skipping makes the sequence less predictable. Interactions should be evaluated rather than assuming that each system reaches its design state independently.[19]

Active systems can contain many components in series. ABCB gives illustrative reliability calculations using assigned component values, but these are simplified examples rather than universal system probabilities. Their purpose is to show how complexity and dependencies can reduce availability.[20]

Normal building ventilation can either support or oppose the fire-mode arrangement. Recirculation can distribute smoke if the system does not change to its intended state. The design should document fan, damper and control positions for each relevant operating mode.[21][15]

Commissioning and design limits

Commissioning should include an installation check, performance tests in all operating modes, repair of defects and retesting. ABCB presents this sequence because a completed installation is not necessarily a functioning system. Repeated testing may be needed to close identified defects.[22]

Access for inspection and maintenance affects reliability over the system's life. Components that cannot be reached safely are harder to test and service. Documentation should identify required inspections and the mode in which each component is expected to operate.[22]

Calculations carry uncertainty from the fire, geometry and flow paths. IFEG notes that smoke-spread calculations beyond the enclosure of origin are more difficult and uncertain than those within it. Results should not be given more precision than those inputs support.[23]

Dilution alone should not be confused with every definition of smoke control. NUREG-1805's cited glossary definition distinguishes pressure- and airflow-based control from simple supply-and-extract dilution within an enclosure. Broader smoke-management classifications nevertheless include dilution as one technique.[14][12]

What the system is intended to protect

Atria connect spaces that might otherwise be separated into smaller compartments. Without suitable barriers, smoke can spread through the shared volume and reach communicating areas; Milke identifies this as a different problem from smoke control in a well-compartmented building. Pressure differences across barriers cannot perform the same function where the required physical separation is absent.[24]

The large volume can initially moderate the hazard. Air mixed into the plume reduces the concentration of combustion products and lowers the smoke temperature; however, dilution also increases the quantity of gas delivered to the layer. A benefit in concentration therefore accompanies an increased smoke-handling demand.[25]

Life-safety assessment considers several properties of the smoke environment. These include layer-interface height, visibility, temperature and the concentrations of harmful gases. The layer height describes whether an occupied level becomes immersed in smoke; it does not, by itself, describe the severity of every possible exposure within that layer.[25]

Reduced visibility can slow movement and increase disorientation; Milke also describes the potential for trips and falls where occupants cannot see obstructions or balcony edges. Longer evacuation then extends the period of exposure to smoke. A low predicted temperature does not remove these visibility-related effects.[25]

Property objectives can differ from life-safety objectives. Smoke can stain contents, expose equipment to corrosive products and interrupt the use of a building. A smoke concentration that permits short-term movement can still be unacceptable for sensitive contents. The chosen performance objective therefore influences the conditions that the system is intended to maintain.[25]

Purpose and route continuity

The central purpose is timely movement away from a threat. A route begins where occupants may be present and continues through the connected spaces and components leading to safety. Every link must be usable, because a failure near the destination can defeat an otherwise adequate path.[26][27] The threatened end deserves particular attention; Proulx distinguishes an emphasis on exit capacity from an emphasis on the decisions and conditions facing occupants at the start. A route with a safe discharge does not help if occupants cannot recognise or reach it in time.[28]

A place of safety must suit the intended occupants. The 2005 International Fire Engineering Guidelines (IFEG) give an example performance framework for this destination. It describes protection from untenable conditions, suitable communication and enough space for those expected to use it. The destination is therefore part of the escape provision, not an undefined endpoint beyond the exit.[29]

Evacuation uses these provisions within a timed human response. Warning, interpretation and preparation occur before directed travel, and queues can occur along the way. The physical route must be assessed together with those stages rather than in isolation.[30][31]

Route continuity also includes doors and other operating elements. A door that cannot open in the required condition interrupts the path just as a physical obstruction would. Management and maintenance must preserve the route's intended operation.[32]

Engineering evaluation

Evaluation should begin with the number and distribution of occupants. Different groups may start in different spaces and need different levels of assistance. Their routes should be traced separately where those differences affect preparation, travel or the place of safety.[33]

Underground and windowless structures: engineering evaluation, showing the relationships described in the text.
Engineering evaluation in the assessment of Underground and windowless structures.

Each proposed route should be checked as a continuous chain. The review includes the initial room, successive passages, doors, protected elements and final destination. A nominal exit on the plan does not establish that every part of that chain remains available during a fire.[34]

Alternative routes should be assessed for independence from the same threat. Two paths that share a smoke-affected space or an impaired component may not offer the intended choice. The Canadian code intentions reproduced in IFEG connect alternative exits with reduced delay and obstruction risks.[35]

The relevant fire conditions should be stated. A fire in an occupied room, a fire blocking an exit and smoke entering a protected route create different demands. C/VM2's exit-blocking scenario provides a specific example of testing whether a viable route remains.[34]

Timing should include detection, notification, preparation and movement. Route geometry and flow capacity affect only some of those stages. An assessment that starts when occupants reach the corridor would miss the time needed to recognise and respond to the event.[30]

The safety systems assumed in the analysis should be identified. Suppression, compartmentation, smoke control and emergency power can alter route conditions, but their functions depend on equipment and maintenance. Their failure modes may require a separate scenario or sensitivity check.[36][37]

Evidence from drills can reveal how the route and procedures operate together. Queue locations, unclear signs, door operation and staff directions can be observed in the actual layout. The drill's warning and population conditions must accompany any comparison with a fire scenario.[38]

See also

Notes

  1. ↑ Milke (2002), pp. 4-292–4-295.
  2. ↑ 2.0 2.1 2.2 Cote et al. (2008), §20.20, pp. 20-217–20-219.
  3. ↑ 3.0 3.1 3.2 Cote et al. (2008), §20.20, pp. 20-218–20-219.
  4. ↑ 4.0 4.1 4.2 4.3 Cote et al. (2008), §20.20, p. 20-218.
  5. ↑ Nelson and Mowrer (2002), pp. 3-367–3-372.
  6. ↑ Australian Building Codes Board et al. (2005), pp. 1.8-13–1.8-14.
  7. ↑ Cote et al. (2008), §20.20, pp. 20-217–20-218.
  8. ↑ Australian Building Codes Board et al. (2005), pp. 2.5-1–2.5-2, 2.5-6.
  9. ↑ Milke (2002), pp. 4-304–4-306.
  10. ↑ 10.0 10.1 Australian Building Codes Board et al. (2005), pp. 2.5-6–2.5-7.
  11. ↑ Australian Building Codes Board et al. (2005), pp. 1.8-13–1.8-14; 2.5-6–2.5-7.
  12. ↑ 12.0 12.1 Australian Building Codes Board et al. (2005), p. 2.5-7.
  13. ↑ Cooper (2002), p. 3-219.
  14. ↑ 14.0 14.1 Nolan (2000), as cited in Iqbal and Salley (2004), pp. F-50–F-51.
  15. ↑ 15.0 15.1 15.2 Evans et al. (2005), pp. 69–71.
  16. ↑ Australian Building Codes Board (2020), pp. 128–129.
  17. ↑ Australian Building Codes Board et al. (2005), p. 2.5-4.
  18. ↑ Australian Building Codes Board (2020), p. 131.
  19. ↑ Cooper (2002), p. 3-239.
  20. ↑ Australian Building Codes Board (2020), p. 129.
  21. ↑ Australian Building Codes Board (2020), p. 126.
  22. ↑ 22.0 22.1 Australian Building Codes Board (2020), pp. 129–130.
  23. ↑ Australian Building Codes Board et al. (2005), p. 2.5-6.
  24. ↑ Milke (2002), pp. 4-292–4-294.
  25. ↑ 25.0 25.1 25.2 25.3 Milke (2002), pp. 4-292–4-293.
  26. ↑ Australian Building Codes Board et al. (2005), p. 1.2-18.
  27. ↑ Ministry of Business, Innovation and Employment (2025), pp. 32–33.
  28. ↑ Proulx (2002), pp. 3-342–3-343.
  29. ↑ Australian Building Codes Board et al. (2005), p. 1.2-15.
  30. ↑ 30.0 30.1 Australian Building Codes Board et al. (2005), pp. 2.8-1–2.8-2.
  31. ↑ Proulx (2002), pp. 3-347–3-348.
  32. ↑ Australian Building Codes Board et al. (2005), pp. 1.8-13–1.8-14.
  33. ↑ Proulx (2002), p. 3-350.
  34. ↑ 34.0 34.1 Ministry of Business, Innovation and Employment (2025), p. 37.
  35. ↑ Australian Building Codes Board et al. (2005), pp. 1.2-16–1.2-17.
  36. ↑ Australian Building Codes Board (2020), pp. 131–132.
  37. ↑ Razza and Grill (2005), pp. 3–4.
  38. ↑ Proulx (2002), pp. 3-348–3-350.

References

  • Australian Building Codes Board, National Research Council of Canada, International Code Council, & Department of Building and Housing New Zealand. (2005). International fire engineering guidelines. Australian Building Codes Board.
  • Australian Building Codes Board. (2020). Fire safety verification method: Data sheets (Handbook annex, Print version 1.1).
  • Cooper, L. Y. (2002). Smoke and heat venting. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-219–3-242). National Fire Protection Association.
  • Cote, A. E., Grant, C. C., Hall, J. R., Jr., & Solomon, R. E. (Eds.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
  • Evans, D. D., Peacock, R. D., Kuligowski, E. D., Dols, W. S., & Grosshandler, W. L. (2005). Active fire protection systems (NIST NCSTAR 1-4). National Institute of Standards and Technology.
  • Iqbal, N., & Salley, M. H. (2004). Fire dynamics tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission fire protection inspection program (NUREG-1805). U.S. Nuclear Regulatory Commission.
  • Milke, J. A. (2002). Smoke management in covered malls and atria. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-292–4-310). National Fire Protection Association.
  • Ministry of Business, Innovation and Employment. (2025). C protection from fire: Verification method C/VM2 (2nd ed.).
  • Nelson, H. E., & Mowrer, F. W. (2002). Emergency movement. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-367–3-380). National Fire Protection Association.
  • Proulx, G. (2002). Movement of people: The evacuation timing. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-342–3-366). National Fire Protection Association.
  • Razza, J. C., & Grill, R. A. (2005). Comparison of the 1968 and current (2003) New York City building code provisions (NIST NCSTAR 1-1F). National Institute of Standards and Technology.