Skip to content
From Fire Safety Academy Wiki
Revision as of 08:09, 8 November 2026 by Lisa (talk | contribs) (Add 4 watermarked NFPA SVG illustrations)
Contents
  1. 1Magnesium as a fuel
  2. 2Ignition
  3. 3Reactions with water and other agents
    1. 3.1Hydrogen released from water: worked example
  4. 4Dust explosions
  5. 5Fighting magnesium fires
  6. 6Prevention in storage and processing
  7. 7Limitations and misconceptions
  8. 8See also
  9. 9Notes
  10. 10References

A magnesium fire is a fire in which magnesium metal or one of its alloys burns. Magnesium is a combustible metal, and its fires belong to Class D of the fire classes used in the United States.[1][2] Castings and other large pieces are difficult to ignite, but ribbons, chips, shavings and powder ignite easily, some of them with a match flame.[3]

Once ignited, magnesium burns intensely, melts as it burns and is difficult to extinguish. Its flames can reach about 1,370 °C.[3] Magnesium combines so readily with oxygen that it burns in carbon dioxide and in nitrogen, and it can decompose water, releasing hydrogen while oxygen combines with the metal.[4] Water, water solutions, carbon dioxide and halogenated agents therefore do not work on burning magnesium chips, and some make the fire worse. Small fires can be smothered with a compatible dry powder such as graphite or sodium chloride; argon or helium can be used to blanket a fire in an enclosed space.[4][5] In the US practice described by Christman (2008), NFPA 484, Standard for Combustible Metals, addresses the storage and processing of magnesium.[3]

Magnesium as a fuel

Combustion needs fuel, oxygen and a sufficiently high temperature, the three sides of the fire triangle. Air contains 21 % oxygen and 78 % nitrogen by volume.[6] Magnesium is an unusual fuel because it does not depend on the oxygen of the air: it also burns in an atmosphere of carbon dioxide and in nitrogen, with which it forms magnesium nitride.[4] Lemoff (2008) gives magnesium as the example of a metal that reacts vigorously in carbon dioxide or nitrogen.[7]

Metal sold as "magnesium" is often one of many alloys that contain mainly magnesium, with significant percentages of aluminium, manganese and zinc.[3] Pure magnesium melts at 650 °C and boils at 1,110 °C.[8] Its heat of combustion to magnesium oxide is 24.73 MJ/kg.[9] Flame temperatures can reach 1,371 °C (2,500 °F), although the flame above the burning metal is usually less than 305 mm (12 in.) high.[3]

Magnesium conducts heat well. At 20 °C pure magnesium has a density of 1,746 kg/m³ and a thermal conductivity of 171 W/(m·K).[10] Steel, for comparison, has 45.8 W/(m·K) and oak 0.17 W/(m·K).[11] Pure magnesium thus conducts heat about 3.7 times as well as steel and about 1,000 times as well as oak. A magnesium-aluminium alloy with 6–8 % aluminium and 1–2 % zinc has a lower conductivity of 66 W/(m·K).[10]

The handbook mentions magnesium in several applications. Aircraft contain aluminium, magnesium and titanium, which can and do burn if heated sufficiently.[12] For ships, the US Coast Guard, as described by Eberly (2008), considers all metals inherently noncombustible except magnesium and magnesium alloys.[13] In industry, magnesium is machined, cast in foundries and heat-treated, and each of these processes has its own fire hazards.[3][4]

Ignition

The ease of ignition depends mainly on the form of the metal. Thin, small pieces such as ribbons, chips and shavings may be ignited by a match flame. Castings and other large pieces are difficult to ignite even with a torch, because the high thermal conductivity carries the heat away.[3] To ignite a large piece it is usually necessary to raise the whole piece to its ignition temperature.[3] The more massive the piece, the more difficult it is to ignite.[3]

Bar chart of magnesium ignition temperatures by form, from 623 °C for massive metal down to below 482 °C for powder and 427 °C for some alloys.
Ignition temperatures of magnesium in different forms, compared with the melting point of 650 °C. Based on Christman (2008), pp. 6-155–6-156 and Schwab (2008c), p. 6-143.
Ignition temperatures of magnesium in different forms (converted from °F where the source gives °F)
Form Ignition temperature Source
Massive pure metal, solid 623 °C (1,153 °F) Christman (2008), p. 6-155
Massive metal, general very close to the melting point of 650 °C (1,202 °F) Christman (2008), p. 6-155
Ribbons and shavings about 510 °C (950 °F) Christman (2008), p. 6-155
Finely divided powder below 482 °C (900 °F) Christman (2008), p. 6-155
Certain alloys as low as 427 °C (800 °F) Christman (2008), p. 6-156
Milled powder, Grade B, dust cloud 560 °C Schwab (2008c), p. 6-143
Milled powder, Grade B, dust layer 430 °C Schwab (2008c), p. 6-143

Ignition can come from several sources. Scrap chips and fines may start to burn when waste rags or other contaminants ignite.[3] In machining, dull or deformed tools can create enough frictional heat to ignite the chips.[3] Magnesium castings in contact with aluminium in a heat-treating oven ignite at a lower temperature than on a steel car or tray.[4] Aluminium in contact with magnesium also burns readily, perhaps because an alloy forms at the interface.[5]

a small pile of magnesium turnings burning with a brilliant white flame on a steel tray during a controlled test.
Magnesium turnings burning on a steel tray in a controlled outdoor test: thin pieces ignite easily and burn with a brilliant flame. Based on Christman (2008), pp. 6-155–6-156.

Some ignitions need no outside flame at all. Chips wet with animal or vegetable oils may burn if the oil ignites spontaneously.[3] Grinding fines that are only slightly wetted with water may generate enough heat to ignite spontaneously in air. They then burn violently, taking oxygen from the water and releasing hydrogen, which can also ignite.[3] Magnesium nitride, which sometimes appears on the surface of castings, is a pyrophoric material that can explode under a very minor impact.[14] In oxygen-rich systems, titanium, magnesium and lithium are the most ignitable common metals.[15]

Reactions with water and other agents

Magnesium is a water-reactive material. Chips wet with water, with water-soluble oils or with oils containing more than 0.2 % fatty acid may generate hydrogen gas.[3] Grinding fines generate hydrogen when submerged in water, but the particles cannot be ignited as long as they stay immersed.[3] Compounded cutting oils that are acidic, or become acidic with use, should not be used for machining magnesium, because the acid reacts with the metal and releases hydrogen.[16]

In a fire the reaction is far more violent. Under some conditions, water applied to burning magnesium is decomposed into oxygen and hydrogen. The oxygen combines with the magnesium, and the released hydrogen burns and adds to the intensity of the fire.[4] Molten magnesium forms puddles that are an explosion hazard in the presence of water.[3] Christman (2008) warns that water applied to a burning motor block machined from magnesium can throw molten metal through the air.[8]

Three panels: water on burning magnesium releases burning hydrogen; magnesium keeps burning in carbon dioxide; in nitrogen it forms magnesium nitride.
Burning magnesium takes oxygen from water and keeps burning in carbon dioxide; in nitrogen it forms magnesium nitride. Only noble gases such as argon and helium are inert towards it. Based on Christman (2008), p. 6-157.

Other common agents fail too. Magnesium decomposes carbon dioxide, so carbon dioxide cannot extinguish it.[17] Halogen-containing agents, including the halons and many halon replacements, react violently with burning magnesium.[4] In the SFPE Handbook, Grant (2002) lists magnesium among the reactive metals that burn so intensely that they overpower Halon 1301.[18] Of the inert gases, only the noble gases such as helium and argon are suitable.[4] Yu and Newman (2008) note that helium, neon and argon are too expensive for general use and are justified only in special cases, such as magnesium fires.[19]

Hydrogen released from water: worked example

For illustration, take the oxide-forming reaction of burning magnesium with water. Christman (2008) states that oxygen from water combines with magnesium while hydrogen is released.[4] With magnesium oxide as the product, one mole of magnesium releases one mole of hydrogen.[9] The number of moles in a mass of metal is the mass divided by the atomic weight. The volume of the hydrogen then follows from the ideal gas law, which relates pressure, volume, temperature and amount of gas:[20]

Mg+H2O→MgO+H2

n=mMMgVH2=nRTp

Symbols used in the hydrogen calculation
Symbol Description Unit
m mass of magnesium that reacts g
MMg atomic weight of magnesium, 24.31 g/mol
n amount of magnesium, equal to the amount of hydrogen released mol
R ideal gas constant, 8.314 J/(mol·K)
T absolute temperature of the gas K
p pressure of the gas Pa
VH2 volume of hydrogen released m³

Take 1 kg of magnesium metal that reacts completely by this oxide-forming pathway. The atomic weight of magnesium is 24.31, so 1,000 g is 41.1 mol, which releases 41.1 mol or 83.1 g of hydrogen.[21] At 20 °C, which is 293.15 K, and at 101.3 kPa, the volume is 41.1 × 8.314 × 293.15 / 101,300 = 0.990 m³.[22][20] Hydrogen is flammable in air between 4 % and 75 % by volume.[23] The hydrogen from 1 kg of magnesium is therefore enough to make about 24.7 m³ of hydrogen-air mixture at the lower flammable limit, if it mixes uniformly. The calculation illustrates why Christman (2008) calls for ventilation of drums of grinding fines to limit hydrogen buildup. He describes holes in the lid or a non-sealing lid to reduce the explosion hazard when a drum is opened.[3]

Sketch: 1 kg of magnesium metal, a 0.99 m³ cube of hydrogen and a 24.7 m³ cube of hydrogen-air mixture at 4 %.
Worked example: 1 kg of magnesium metal following the oxide-forming water reaction releases about 0.99 m³ of hydrogen at 20 °C, enough for about 24.7 m³ of mixture at the lower flammable limit of 4 %. Based on Christman (2008), p. 6-157, Drysdale (2008), pp. 2-9 and 2-14, and Rivkin (2008b), p. 21-55.

The result is an upper bound, because it assumes complete reaction, ideal-gas behaviour and uniform mixing. It does not cover hydrogen safety as a whole. It does show that even a small mass of wet magnesium can produce a large flammable volume.

Dust explosions

Magnesium dust clouds are explosive if an ignition source is present.[3] Three tables in the handbook give data for magnesium dust. Two rate it as severe on the Bureau of Mines explosibility index, and all three show low minimum explosible concentrations, but the values differ between samples and test methods.[24][25][26] Layers of magnesium dust also need less energy for ignition than carbonaceous materials.[27]

Explosion data for magnesium dust (pressures and rates converted from psig and psi/s)
Property US Bureau of Mines (Dobbs (2008), p. 9-69) Milled, Grade B (Schwab (2008c), p. 6-143) 28 µm powder (Schwab (2008c), p. 6-145)
Minimum explosible concentration 40 g/m³ 30 g/m³ 30 g/m³
Minimum ignition energy, dust cloud 40 mJ 40 mJ –
Maximum explosion pressure 621 kPa (90 psig) 800 kPa (116 psig) 17.5 bar (gauge)
Maximum rate of pressure rise 62.1 MPa/s (9,000 psi/s) 103 MPa/s (15,000 psi/s) –
Deflagration index KSt – – 508 bar·m/s
Explosibility index more than 10 (severe) more than 10 –

A KSt of 508 bar·m/s places magnesium close to aluminium powder, with 515 bar·m/s, and far above most other dusts in the same table.[26] Schwab (2008c) stresses that these test data are only a qualitative indication of the hazard and should not be used for design.[28] Carbon dioxide should not be used for inerting magnesium dust, and the inert gas in pneumatic systems for magnesium dust should not contain carbon dioxide.[29][30] More on the general hazard is given under dust explosion.

Grinding equipment for magnesium should have a liquid precipitation separator. It should be interlocked so that it can operate only while the exhaust blower and the water spray work properly, and it should be used for magnesium only.[3] Because wet sludge is hard to dispose of, NFPA 484, as described by Christman (2008), also permits dry cyclone collectors that are located and protected as that standard requires. The collection media must be outside the building and protected so that an explosion or fire in them does not injure people.[3]

Fighting magnesium fires

The method of extinguishment depends largely on the form of the burning material.[4] Burning chips, shavings and small parts must be smothered and cooled with a suitable dry agent, such as graphite or dry sodium chloride. Where magnesium dust is present, the agent must be applied so that no dust cloud forms, because a cloud may lead to a dust explosion.[4] Fires in solid magnesium can be fought without difficulty if attacked early. It may be possible to remove the surrounding material and let the small quantity of magnesium burn itself out harmlessly.[4]

Decision chart: dry agent on chips, burn-out for solid pieces, fluxes or boron trifluoride in ovens, sprinklers to protect the building.
Choice of method for magnesium fires by form and setting, with the agents that must not be used. Based on Christman (2008), pp. 6-157–6-158 and Yu and Newman (2008), p. 2-91.

These agents are a special type of extinguishing agent. A dry powder extinguishing agent is tested and listed for specific combustible metals, and Conroy (2008) describes the sodium chloride and graphite-based G-1 powders as the two most common.[31][32] They should not be confused with a dry chemical extinguishing agent, which is not effective on Class D fires because the heat of the burning metal consumes it.[33] Yu and Newman (2008) list several powders for magnesium, including G-1 or MetalGuard, Lith-X, foundry flux, Pyromet and T.E.C., as well as trimethoxyboroxine liquid and the gases boron trifluoride, boron trichloride, helium and argon.[34] Fires in magnesium filings are more difficult to put out than fires in magnesium scrap and need more agent.[35]

Water is not completely ruled out. Large quantities of water have extinguished small quantities of burning magnesium, in the absence of pools of molten metal.[34] Automatic sprinklers are considered desirable, because they give automatic notification and control of a fire.[4] The water may at first intensify the magnesium combustion, but it protects the structure and prevents ignition of the surrounding combustible material.[36] Frank (2008) notes that NFPA 484 specifies when sprinklers may and may not be used where magnesium is present, and that water can protect exposures.[37]

Heat-treating ovens are a special case. Fires in them are best controlled with powders and gases developed for such fires. Melting fluxes that exclude air from the burning metal have extinguished fires in heat-treating furnaces, and boron trifluoride gas is effective on small fires in them.[36] Ultraviolet flame detectors are sensitive to most fires, including fires in metals such as magnesium.[38]

Pyrotechnic flare material made of magnesium and Teflon is the opposite extreme. Gagnon (2008) describes it as among the fastest-burning materials, too fast for a deluge system that put water on a fire within 18 ms.[39] A blast-initiated deluge system that discharged water at about 152 m/s extinguished 0.454 kg samples in an average of 15 ms and 1.81 kg samples in 40–50 ms.[40] This case concerns a pyrotechnic mixture, not the bulk metal of a machine shop or foundry.

Prevention in storage and processing

In the United States, NFPA 484, as described by Christman (2008), recommends maximum quantities of the various sizes and forms of magnesium for specific storage locations. The storage building should be noncombustible, and magnesium should be kept apart from combustible material.[3] Dry fines and fine scrap are best kept in covered noncombustible containers in separate fire-resistive buildings or rooms with explosion venting. In combustible buildings, NFPA 484 recommends automatic sprinklers to control a fire before the magnesium becomes involved.[3] Wet scrap fines are preferably stored outdoors in covered, vented noncombustible containers.[3] In the United States, magnesium powder, pellets and ribbon are shipped as a flammable solid and labelled under Department of Transportation requirements.[3]

Machining of magnesium is normally done dry. If cutting fluids are used, they should be mineral oils with high flashpoints, because water and water-oil emulsions make wet shavings release hydrogen and burn more violently.[3] Machines and work areas should be cleaned often. The waste should be kept in covered, clean, dry steel or other noncombustible drums and removed from the building at regular intervals.[3]

Molten magnesium needs its own precautions. Foundries use sulphur dioxide or melting fluxes to prevent oxidation or ignition, but sulphur dioxide only excludes air and is not an extinguishing agent.[3] Pots, crucibles and ladles must be kept dry to prevent steam formation or a violent metal-water reaction. Run-off pits should be steel-lined and free of iron scale, because leaking metal on hot iron scale causes a violent thermite reaction.[4]

Heat treatment brings temperatures close to the ignition temperatures of the alloys, so hot spots must be avoided. Fine casting fins, sprues, chips and dust ignite more readily than large castings, which should therefore be cleaned before heat-treating.[4] Magnesium should not be heat-treated in nitrate salt baths, because some nitrate and nitrite mixtures react explosively with it, particularly above 538 °C (1,000 °F).[4]

Scrap must be handled with care until disposal. Severson (2008) describes burning fine chips and dust-collector sludge in a purpose-built incinerator or a safely located outdoor area paved with fire-brick or hard-burned paving brick. In the outdoor method, the layer was about 102 mm (4 in.) thick, with ordinary combustible material placed on top and ignited.[41] The same source describes deactivating sludge with a 0.5 % ferrous chloride solution in an open container outdoors, because that reaction releases hydrogen.[41]

Limitations and misconceptions

A frequent misconception is that magnesium parts are safe because a solid piece is hard to ignite. A massive casting may resist a torch, while thin chips and shavings of the same alloy may ignite from a match flame.[3] The word "magnesium" also covers many alloys, some of which ignite much lower than the pure metal and conduct heat less well.[3][10]

The rules on water are often simplified too far in both directions. Water is generally dangerous on burning magnesium chips, molten pools and machined parts.[8][4] Yet large amounts of water have put out small magnesium fires, and sprinklers are recommended to protect the building and its other contents.[34][36] Inert gases are a similar trap: nitrogen and carbon dioxide, which extinguish ordinary fires mainly by dilution, react with burning magnesium.[19][4]

Published property data are uncertain. The ignition temperature of the massive metal is given both as 623 °C and as very close to the melting point of 650 °C.[8] The three dust tables give minimum explosible concentrations of 30–40 g/m³ and maximum pressures between about 0.6 and 1.75 MPa.[24][25][26] Such data depend on particle size, shape and moisture, so a specific dust must be tested before protection is designed.[28]

See also

Notes

  1. ↑ Christman (2008), p. 6-153.
  2. ↑ Conroy (2008), p. 17-71.
  3. ↑ 3.00 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 Christman (2008), p. 6-156.
  4. ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 Christman (2008), p. 6-157.
  5. ↑ 5.0 5.1 Christman (2008), p. 6-161.
  6. ↑ Van Rossum (2027), §4.2.
  7. ↑ Lemoff (2008), p. 6-166.
  8. ↑ 8.0 8.1 8.2 8.3 Christman (2008), p. 6-155.
  9. ↑ 9.0 9.1 Babrauskas (2008a), p. 6-281.
  10. ↑ 10.0 10.1 10.2 DiNenno et al. (2002), p. A-31.
  11. ↑ Van Rossum (2027), §5.5.
  12. ↑ Boucher (2008), p. 21-142.
  13. ↑ Eberly (2008), p. 21-172.
  14. ↑ Dobbs (2008), p. 9-72.
  15. ↑ Rosales and Stoltzfus (2008), p. 9-236.
  16. ↑ Dobbs (2008), p. 9-70.
  17. ↑ Wysocki (2008), p. 17-6.
  18. ↑ Grant (2002), p. 4-152.
  19. ↑ 19.0 19.1 Yu and Newman (2008), p. 2-86.
  20. ↑ 20.0 20.1 Drysdale (2008), p. 2-9.
  21. ↑ Drysdale (2008), p. 2-14.
  22. ↑ Van Rossum (2027), §3.2.
  23. ↑ Rivkin (2008b), p. 21-55.
  24. ↑ 24.0 24.1 Dobbs (2008), p. 9-69.
  25. ↑ 25.0 25.1 Schwab (2008c), p. 6-143.
  26. ↑ 26.0 26.1 26.2 Schwab (2008c), p. 6-145.
  27. ↑ Scarbrough (2008a), p. 11-65.
  28. ↑ 28.0 28.1 Schwab (2008c), p. 6-147.
  29. ↑ Ural and Garzia (2008), p. 17-149.
  30. ↑ Bouchard (2008), p. 8-39.
  31. ↑ Conroy (2008), p. 17-76.
  32. ↑ Conroy (2008), p. 17-81.
  33. ↑ Lake (2008), p. 17-17.
  34. ↑ 34.0 34.1 34.2 Yu and Newman (2008), p. 2-91.
  35. ↑ Conroy (2008), p. 17-87.
  36. ↑ 36.0 36.1 36.2 Christman (2008), p. 6-158.
  37. ↑ Frank (2008), p. 17-41.
  38. ↑ Dungan (2008a), p. 14-24.
  39. ↑ Gagnon (2008), p. 16-130.
  40. ↑ Gagnon (2008), p. 16-131.
  41. ↑ 41.0 41.1 Severson (2008), p. 7-66.

References

  • Babrauskas, V. (2008a). Tables and charts. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-269–6-294). National Fire Protection Association.
  • Bouchard, J. K. (2008). Materials-Handling equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-31–8-41). National Fire Protection Association.
  • Boucher, B. (2008). Aviation. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-135–21-149). National Fire Protection Association.
  • Christman, T. (2008). Metals. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-153–6-164). National Fire Protection Association.
  • Conroy, M. T. (2008). Fire extinguisher use and maintenance. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-71–17-92). National Fire Protection Association.
  • DiNenno, P. J., Drysdale, D., Beyler, C. L., Walton, W. D., Custer, R. L. P., Hall, J. R., Jr., & Watts, J. M., Jr. (Eds.). (2002). SFPE handbook of fire protection engineering (3rd ed.). National Fire Protection Association; Society of Fire Protection Engineers.
  • Dobbs, P. G. (2008). Metalworking processes. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-67–9-72). National Fire Protection Association.
  • Drysdale, D. (2008). Physics and chemistry of fire. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-3–2-20). National Fire Protection Association.
  • Dungan, K. W. (2008a). Automatic fire detectors. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-15–14-28). National Fire Protection Association.
  • Eberly, R. (2008). Marine vessels. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-151–21-185). National Fire Protection Association.
  • Frank, J. A. (2008). Characteristics and hazards of water and water additives for fire suppression. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-31–17-43). National Fire Protection Association.
  • Gagnon, R. M. (2008). Ultra-High-Speed water spray systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 16-109–16-133). National Fire Protection Association.
  • Grant, C. C. (2002). Halon design calculations. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-149–4-172). National Fire Protection Association; Society of Fire Protection Engineers.
  • Lake, J. D. (2008). Chemical extinguishing agents and application systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-17–17-29). National Fire Protection Association.
  • Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
  • Rivkin, C. H. (2008b). Vehicle fueling using gaseous fuels. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-41–21-76). National Fire Protection Association.
  • Rosales, K., & Stoltzfus, J. M. (2008). Oxygen-Enriched atmospheres. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-225–9-243). National Fire Protection Association.
  • Scarbrough, D. R. (2008a). Control of electrostatic ignition sources. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 11-59–11-68). National Fire Protection Association.
  • Schwab, R. F. (2008c). Dusts. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-141–6-152). National Fire Protection Association.
  • Severson, P. R. (2008). Hazardous waste control. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-57–7-69). National Fire Protection Association.
  • Ural, E. A., & Garzia, H. W. (2008). Explosion prevention and protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-141–17-165). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
  • Wysocki, T. J. (2008). Carbon dioxide and application systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-3–17-15). National Fire Protection Association.
  • Yu, H.-Z., & Newman, J. S. (2008). Theory of fire extinguishment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-79–2-92). National Fire Protection Association.