Skip to content
From Fire Safety Academy Wiki
Revision as of 22:05, 7 November 2026 by Peter (talk | contribs) (New FSE wiki article: Oxidiser (written by Claude Opus 5.5))
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Contents
  1. 1Definition
  2. 2Role in combustion
  3. 3Common oxidising chemicals
  4. 4Oxidising gases
  5. 5Hazards in storage and fire
  6. 6Storage, segregation and classification
  7. 7Fire control
  8. 8Common misconceptions
  9. 9See also
  10. 10Notes
  11. 11References

An oxidiser (American spelling oxidizer), also called an oxidising agent, is a material that can cause or enhance the combustion of other materials, generally by yielding oxygen.[1] Every fire needs one, and in most fires it is simply the oxygen in the air.[2][3] In fire protection the word usually refers to chemicals and gases that carry their own supply of oxygen or another oxidising species. Examples are nitrates, chlorates, peroxides and hypochlorites, and oxidising gases such as pure oxygen and nitrous oxide.[4][5]

Most of these substances do not burn themselves, but they make combustible material easier to ignite and faster to burn, and some mixtures can explode.[4][6] The handbook names combustible packaging, wooden and plastic pallets, spills mixed with refuse and floor sweepings as examples of such fuels.[7][4][8] Because the oxidiser furnishes its own oxygen, carbon dioxide and other smothering agents are of little value, and large quantities of water are the usual means of control.[8] In the international transport classes, as described by C. J. Wright (2008a), oxidisers form Division 5.1. In the United States they are marked "OX" in the NFPA 704 diamond and stored under NFPA 430, as described in the 2008 edition of the Fire Protection Handbook.[9][10][4]

Definition

The transport definition reproduced by C. J. Wright (2008a) describes an oxidiser as "a material that may, generally by yielding oxygen, cause or enhance the combustion of other materials".[1] NFPA 430, Code for the Storage of Liquid and Solid Oxidizers, as quoted by Harrington (2008), uses a broader wording. It covers any material that readily yields oxygen or another oxidising gas, or that readily reacts to promote or initiate the combustion of combustible materials. The same definition adds that such a material can undergo a vigorous, self-sustained decomposition when it is contaminated or heated.[11] The second part matters for storage, because some oxidisers are hazardous on their own and not only in combination with a fuel.[12][8]

Oxidation itself does not always involve oxygen. In the NUREG-1805 glossary, an oxidising agent is a substance that gives up oxygen easily, removes hydrogen from another substance or attracts electrons.[13] Oxygen is therefore not strictly necessary. Hydrocarbons can "burn" in an atmosphere of chlorine, and zirconium dust can be ignited in pure carbon dioxide.[3] Bromine and iodine are noncombustible but support the combustion of certain substances, and turpentine, phosphorus and finely divided metals ignite spontaneously in the presence of the halogens.[14]

Fuel and oxidiser can also be combined in one substance. All organic peroxides are combustible and, like inorganic peroxides, they increase the intensity of a fire.[15] For this reason the transport classes place them next to the oxidisers, in Class 5, as Division 5.2; the article Organic peroxide treats them separately.[1]

Role in combustion

Introduction to Fire Safety Engineering describes combustion as a complex set of mainly exothermic chemical reactions between a fuel and an oxidiser, usually oxygen gas. The reactions release heat and light in the form of a flame or a glow.[16] The fire triangle expresses the same idea: fuel, an oxidising agent and heat must all be present to start a fire.[2] In ordinary fires the oxidiser is the air, which contains 21 % oxygen by volume. When the oxygen level falls, a fire stops spreading and may eventually go out.[17]

The amount of oxygen involved is large. Complete combustion of 1 kg of a cellulosic fuel such as wood needs about 1.25 kg of oxygen, and 1 kg of a hydrocarbon fuel such as petrol needs about 3.46 kg.[18] In a normal fire this oxygen has to reach the fuel from the surrounding air, and a fire in a closed space can be smothered by lack of oxygen.[18] A chemical oxidiser removes that limit, because it furnishes its own oxygen for combustion.[8] Powerful oxidising agents such as sodium nitrate and potassium chlorate, intimately mixed with a solid or liquid fuel, give highly reactive mixtures.[3] Gunpowder is an example: a physical mixture of carbon and sulfur as the fuel with sodium nitrate as the oxidiser.[3]

The next step is to build the oxidising group into the fuel molecule itself. When the nitrate group is incorporated chemically, as in cellulose nitrate or trinitrotoluene (TNT), the substance can be highly unstable and decompose violently.[3] Commercial blasting agents instead mix a separate fuel and oxidiser. The most commonly used explosive is a fuel and oxidiser system of ammonium nitrate with a fuel such as No. 2 diesel fuel, known as ANFO. About 6 % fuel oil is added to specially prepared ammonium nitrate prills.[19]

For buildings, the International Fire Engineering Guidelines note that ignition requires fuel, an oxidiser and a source of heat, and that in most environments the oxidiser is always present.[20] In a qualitative assessment of ignition, attention therefore goes to potential ignition sources, because combustible fuels and oxygen are likely to be present in most instances.[21] The guidelines list oxidising materials, together with open flames, sparks and temperatures capable of causing ignition, among the conditions to be considered.[21]

Common oxidising chemicals

Davenport (2008) describes the inorganic oxidisers family by family. Most of them are not combustible themselves; their danger lies in the oxygen they can provide to other materials.[4] The table summarises the families and the behaviour that the handbook reports for each.

Families of inorganic oxidising chemicals and their behaviour in fire
Family Examples Behaviour reported in the handbook
Nitrates sodium, potassium and ammonium nitrate melt and release oxygen in a fire; molten nitrate reacts violently with organic material and gives toxic oxides of nitrogen[4]
Nitrites ammonium nitrite release oxygen at lower temperatures than nitrates; some are explosive on their own[12]
Inorganic peroxides sodium, potassium, strontium, barium peroxide; hydrogen peroxide release oxygen and heat with water or on heating; mixtures with combustibles can explode[12]
Chlorates and chlorites potassium and sodium chlorate; sodium chlorite give up oxygen more readily than nitrates; mixtures with combustibles may ignite or explode[8]
Perchlorates ammonium, potassium, sodium and magnesium perchlorate more stable than chlorates, but explosive under some conditions[8]
Dichromates ammonium and potassium dichromate ammonium dichromate decomposes on its own above 225 °C (437 °F)[8]
Hypochlorites calcium hypochlorite ignites combustibles on contact above 50 % by weight; decomposes rapidly in a fire[8]
Permanganates and persulfates potassium permanganate, potassium persulfate ignition by friction or with acids; container rupture in a fire[8]

Nitrates are widely used in fertilisers, salt baths and other industrial applications. Sodium nitrate is noncombustible, but it evolves oxygen when heated to about 370 °C (700 °F) and so intensifies any fire nearby. An intimate mixture of sodium nitrate and organic material can be exploded by a flame.[4] Nitrates dissolve in water, and bags of paper, burlap or cloth that become moist retain an impregnation of nitrate after drying. Such bags are highly combustible, so the nitrate is moved to noncombustible bins and storage on wooden floors or against wooden walls is avoided.[4] Ammonium nitrate is a special case: its oxidising gas is nitrous oxide rather than oxygen, and all grades can detonate under suitable conditions.[4]

Hydrogen peroxide is a syrupy liquid and, in pure form, relatively stable. Kept at 100 °C (212 °F), 99.2 % hydrogen peroxide decomposes at a rate of 4 % per year, while 50 to 90 % solutions decompose at something less than 2 % per day. The rate rises about 1.5 times for each 10 K (18 °F) rise in temperature.[12] By that rule, a rise of 30 K multiplies the decomposition rate by about 3.4.

The hazard of hydrogen peroxide depends strongly on its concentration. Solutions of 86 to 90.7 % have been shown to be detonatable, and above about 92 % the liquid can be exploded by shock.[12] Above 35 %, the heat of decomposition is enough to turn all the water into steam, so sudden decomposition can cause a steam explosion. Decomposition can be caused by contamination with iron, copper, chromium and many other metals (except aluminium) or their salts, by combustible dust or by contact with a rough surface.[12][8] Ignition of combustible material in contact with hydrogen peroxide is remote unless the concentration exceeds 35 %.[8]

Potassium chlorate is a white, water-soluble crystalline solid that gives up oxygen even more readily than the nitrates. Mixed with combustible material such as floor sweepings, it might ignite or explode spontaneously, and drums containing chlorates might explode when heated.[8] Sodium chlorite releases explosive chlorine dioxide gas with strong acids and decomposes with the evolution of heat at 175 °C (347 °F).[8] Calcium hypochlorite, sold as a swimming pool disinfectant, is one of the most widely used oxidisers. It is found in retail shops, garden warehouses and home utility rooms, often packed in plastic bottles, drums or bags.[8]

Some corrosive acids are also strong oxidisers. Concentrated nitric acid nitrates organic materials, and wood in contact with the acid or its vapour ignites much more easily.[14] Perchloric acid at its normal commercial strength of 72 % is a strong oxidising agent when heated. Explosions have occurred in wooden and plastic laboratory hoods after long exposure to its vapours.[14]

Oxidising gases

NFPA 55 treats oxidising gases as a separate physical hazard class, as described by Lemoff (2008). They are oxygen, mixtures of oxygen with other gases that contain considerably more oxygen than air, and certain gaseous oxides such as nitrous oxide. These gases are nonflammable, but they support combustion.[5] They make combustibles ignite at lower temperatures, accelerate combustion and can cause the flames of fuel-burning appliances to extend beyond their combustion chambers.[22] In health care, a little pure oxygen increases the intensity of any fire and makes items that are noncombustible in air burn well. Nitrous oxide behaves in a similar way when heated until it dissociates, because pure oxygen is then released in an exothermic reaction.[23]

Oxygen also changes the flammability of gases and vapours. As the oxygen concentration increases, the upper flammable limit rises while the lower limit stays nearly the same. At the lower limit there is already more oxygen than needed for complete combustion, so extra oxygen only replaces inert gas.[24]

Rosales and Stoltzfus (2008) define an oxygen-enriched atmosphere as one with more than 21 % oxygen by volume or an oxygen partial pressure above 160 torr (21.3 kPa), or both.[25] Such an atmosphere does not always raise the hazard. A 4 % oxygen mixture in nitrogen or helium at 12 atm (1216 kPa) will not support the burning of paper, although its oxygen partial pressure is 365 torr (48.7 kPa). Most enriched atmospheres met in practice, however, do increase the hazard.[26]

In storage, containers of flammable gases should not be kept with oxidising gases, because oxygen and nitrous oxide raise the burning rate and flame temperature of flammable gases, and mixtures can explode.[27] In the United States, NFPA 55, as described by Lemoff and Rivkin (2008), requires a separation of 6.1 m (20 ft) between cylinders of such incompatible gas classes. The distance can be reduced without limit by a noncombustible barrier at least 1.5 m (5 ft) high with a fire resistance rating of at least half an hour.[27] Where oxidising gases are stored near combustibles, the primary consideration is how the combustible burns in an enriched oxygen environment, not its ordinary classification.[27]

Hazards in storage and fire

The container can be the first fuel an oxidiser meets. Oxidisers stored in fibre packs or plastic containers may be safe under normal conditions, but in a fire the oxidiser and its combustible package can magnify the fire intensity.[7] Combustible packaging and wooden or plastic pallets are therefore described as a severe hazard that should be eliminated.[4] Calcium hypochlorite shows the effect clearly. Contaminated or exposed to a fire, it decomposes rapidly together with its plastic container and gives off a large amount of heat. This heat can open many automatic sprinklers and ignite surrounding combustibles; depending on the sprinkler design and water supply, the system may be overtaxed and the building destroyed.[8]

Heat alone can start decomposition. Sodium nitrate starts to release oxygen at about 370 °C (700 °F). Ammonium dichromate begins to decompose at 180 °C (356 °F), and above 225 °C (437 °F) the decomposition becomes self-sustaining.[4][8] Closed containers of ammonium dichromate rupture at the decomposition temperature, and oxygen released from persulfates by the heat of a fire can rupture their containers explosively.[8] The general hazard listed for Class 5 in the transport table is that these materials supply oxygen to support combustion and are sensitive to heat, shock, friction or contamination.[9]

Some oxidisers also heat themselves. In the SFPE Handbook, Gray (2002) uses hydrated calcium hypochlorite as an example of self-heating in which the reaction mechanism changes with temperature.[28] The key quantity is the critical ambient temperature, the surrounding temperature above which a body of given size and shape heats up to ignition instead of settling at a mild, stable temperature.[29] For a container of 0.175 m radius this temperature was 60 °C in stirred air in a test oven but 55 °C in still air. Gray uses this result to question empirical oven tests that are used to set safe shipping conditions for self-heating materials.[30]

Accidental mixing is a further route to fire. Davenport (2008) stresses that spills are cleaned up immediately and thoroughly, because spilled oxidiser is likely to become mixed with combustible refuse.[4] Strong oxidisers in contact with organic materials can cause rapid combustion or explosion.[31] Zalosh (2008) lists an explosion at Haskell, Oklahoma, on 26 March 1997, in which the mixing of printing ink solvents and oxidisers killed one person and injured two.[32]

Storage, segregation and classification

The basic rule in the handbook is that combustible materials and flammable liquids are not stored in the same areas as oxidising chemicals, and that storage buildings are of noncombustible or fire-resistive construction.[4] Because some oxidisers react dangerously with specific noncombustible materials as well, the choice of storage also considers these reactions. Chlorates, for example, are not stored with acids, and inorganic peroxides, which yield hydrogen peroxide with acids, are suited to a dry, fire-resistive room without combustibles or acids.[4] Such pairs are the subject of chemical incompatibility. In the United States, NFPA 430 covers the storage of liquid and solid oxidisers, including their protection in retail occupancies, as described in the 2008 edition of the Fire Protection Handbook.[4][8]

Hazard labels need care. The label required for interstate shipment classifies a chemical for transport purposes only, so storage arrangements are based on a full knowledge of its fire, health and reactivity hazards.[4] In laboratories, hazardous chemicals such as oxidisers and organic peroxides are not brought in unless the design, construction and fire protection suit the quantity and hazard, and quantities are kept to the minimum needed.[33] In waste handling, combustible waste is kept separate from self-heating and oxidising materials.[34] Spilled oxidisers and leaking containers are removed to a safe area to await disposal, and most, if not all, oxidisers can be rendered harmless by dilution with water.[35]

In the international transport classes, Class 5 covers oxidisers (Division 5.1) and organic peroxides (Division 5.2). The handbook gives ammonium nitrate fertiliser and dibenzoyl peroxide as examples.[9] NUREG-1805 reproduces the same two divisions in its summary of the United States Department of Transportation classification.[36] In the NFPA 704 diamond, the bottom quadrant carries special information, such as "OX" for oxidisers, beside the numerical ratings from 0 to 4 for health, flammability and reactivity.[10] The United States hazardous waste rules described by Severson (2008) treat oxidisers as ignitable waste. Chlorates, permanganates, inorganic peroxides and nitrates are named as oxidisers that yield oxygen readily to stimulate the combustion of organic matter.[37]

Fire control

With one or two exceptions, water appears to be the only suitable extinguishing agent for fires involving inorganic oxidisers, and it is applied in large quantities to fires involving nitrates, nitrites and chlorates.[8] Carbon dioxide and other smothering agents have little or no value, because the oxidising material furnishes its own oxygen for combustion.[8] A fire in a peroxide spill might be put out with a dry chemical extinguisher or by smothering with dry sand or soda ash. If that fails, the area is flooded with water from hose streams.[38] Fire fighters wear self-contained breathing apparatus, because fires involving nitrates produce oxides of nitrogen. Solid water streams striking molten nitrate can cause steam explosions and a violent eruption of the molten material.[38]

Other agents share the same limitation. Ordinary dry chemical will not extinguish fires in materials that supply their own oxygen.[39] Gaseous extinguishing agents are generally not suitable for hazards that contain oxidisers.[11] In the SFPE Handbook, Grant (2002) explains that fuels containing their own oxidising agent burn freely in halon. In gunpowder, rocket propellants and cellulose nitrate the oxidiser sits too close to the fuel, and the agent cannot reach the fire zone fast enough.[40] Medium- and high-expansion foam should not be used on chemicals that release enough oxygen or other oxidising agents to sustain combustion, unless an evaluation including tests shows it to be acceptable.[41]

Water is not free of problems either. The peroxides of sodium, potassium, barium and strontium react exothermically with water.[42] Even so, Davenport (2008) advises that water should still be used on burning combustibles near such peroxides.[8] Where oxidisers are present in burning waste, the decision to extinguish is taken only after the consequences have been assessed.[34]

Common misconceptions

One misconception is to treat a noncombustible oxidiser as harmless in a fire. Most oxidising chemicals are not combustible, yet they accelerate the burning of the combustible materials around them.[4] A second error is to expect smothering or gaseous agents to work as they do for ordinary fuels; they do not, because the oxygen is already inside the burning mixture.[8][11] A third is to rely on the transport label for storage decisions, although it classifies the chemical for transport only.[4] Finally, oxygen-rich does not automatically mean more dangerous, and oxygen-free does not mean safe. Some oxygen-enriched mixtures cannot support the burning of paper, while chlorine supports the "burning" of hydrocarbons without any oxygen.[26][3]

See also

Notes

  1. ↑ 1.0 1.1 1.2 C. J. Wright (2008a), p. 13-120.
  2. ↑ 2.0 2.1 Madrzykowski and Stroup (2008), p. 2-31.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Drysdale (2008), p. 2-17.
  4. ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 Davenport (2008), p. 7-45.
  5. ↑ 5.0 5.1 Lemoff (2008), p. 6-166.
  6. ↑ Davenport (2008), p. 7-54.
  7. ↑ 7.0 7.1 Davenport (2008), p. 7-44.
  8. ↑ 8.00 8.01 8.02 8.03 8.04 8.05 8.06 8.07 8.08 8.09 8.10 8.11 8.12 8.13 8.14 8.15 8.16 8.17 8.18 8.19 8.20 8.21 Davenport (2008), p. 7-47.
  9. ↑ 9.0 9.1 9.2 C. J. Wright (2008a), p. 13-119.
  10. ↑ 10.0 10.1 C. J. Wright (2008a), p. 13-123.
  11. ↑ 11.0 11.1 11.2 Harrington (2008), p. 17-125.
  12. ↑ 12.0 12.1 12.2 12.3 12.4 12.5 Davenport (2008), p. 7-46.
  13. ↑ Iqbal and Salley (2004), p. F-43.
  14. ↑ 14.0 14.1 14.2 Davenport (2008), p. 7-52.
  15. ↑ Davenport (2008), p. 7-49.
  16. ↑ Van Rossum (2027), §4.1.
  17. ↑ Van Rossum (2027), §4.2.
  18. ↑ 18.0 18.1 Van Rossum (2027), §3.3.
  19. ↑ Santis (2008), p. 6-249.
  20. ↑ National Research Council of Canada et al. (2005), p. 3.3-2.
  21. ↑ 21.0 21.1 National Research Council of Canada et al. (2005), p. 2.4-4.
  22. ↑ Lemoff (2008), p. 6-173.
  23. ↑ Allen (2008), p. 6-188.
  24. ↑ Beyler (2002b), p. 2-174.
  25. ↑ Rosales and Stoltzfus (2008), p. 9-225.
  26. ↑ 26.0 26.1 Rosales and Stoltzfus (2008), p. 9-226.
  27. ↑ 27.0 27.1 27.2 Lemoff and Rivkin (2008), p. 7-38.
  28. ↑ Gray (2002), p. 2-221.
  29. ↑ Gray (2002), p. 2-211.
  30. ↑ Gray (2002), pp. 2-222–2-223.
  31. ↑ Doucet and Gilyeat (2008), p. 11-13.
  32. ↑ Zalosh (2008), p. 2-102.
  33. ↑ Anderson (2008a), p. 9-165.
  34. ↑ 34.0 34.1 Severson (2008), p. 7-65.
  35. ↑ Severson (2008), p. 7-66.
  36. ↑ Iqbal and Salley (2004), p. B-22.
  37. ↑ Severson (2008), p. 7-60.
  38. ↑ 38.0 38.1 Davenport (2008), p. 7-48.
  39. ↑ Lake (2008), p. 17-20.
  40. ↑ Grant (2002), p. 4-152.
  41. ↑ Scheffey and Hickey (2002), p. 4-129.
  42. ↑ Yu and Newman (2008), p. 2-91.

References

  • Allen, M. (2008). Medical gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-187–6-196). National Fire Protection Association.
  • Anderson, R. R. (2008a). Fire protection of laboratories using chemicals. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-157–9-166). National Fire Protection Association.
  • Beyler, C. L. (2002b). Flammability limits of premixed and diffusion flames. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-172–2-187). National Fire Protection Association; Society of Fire Protection Engineers.
  • Davenport, J. A. (2008). Storage and handling of chemicals. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-43–7-55). National Fire Protection Association.
  • Doucet, L. G., & Gilyeat, S. S. (2008). Waste handling and control. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 11-3–11-25). National Fire Protection Association.
  • Drysdale, D. (2008). Physics and chemistry of fire. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-3–2-20). National Fire Protection Association.
  • Grant, C. C. (2002). Halon design calculations. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-149–4-172). National Fire Protection Association; Society of Fire Protection Engineers.
  • Gray, B. (2002). Spontaneous combustion and self-heating. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-211–2-228). National Fire Protection Association; Society of Fire Protection Engineers.
  • Harrington, J. L. (2008). Application of gaseous agents to special hazards fire protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-123–17-139). National Fire Protection Association.
  • Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
  • Lake, J. D. (2008). Chemical extinguishing agents and application systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-17–17-29). National Fire Protection Association.
  • Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
  • Lemoff, T. C., & Rivkin, C. H. (2008). Storage of gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-35–7-42). National Fire Protection Association.
  • Madrzykowski, D., & Stroup, D. W. (2008). Flammability hazard of materials. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-31–2-48). National Fire Protection Association.
  • National Research Council of Canada, International Code Council, Department of Building and Housing, & Australian Building Codes Board. (2005). International fire engineering guidelines (2005 ed.). Australian Building Codes Board.
  • Rosales, K., & Stoltzfus, J. M. (2008). Oxygen-Enriched atmospheres. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-225–9-243). National Fire Protection Association.
  • Santis, L. D. (2008). Explosives and blasting agents. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-247–6-256). National Fire Protection Association.
  • Scheffey, J. L., & Hickey, H. E. (2002). Foam system calculations. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-123–4-148). National Fire Protection Association; Society of Fire Protection Engineers.
  • Severson, P. R. (2008). Hazardous waste control. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-57–7-69). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
  • Wright, C. J. (2008a). Managing the response to hazardous material incidents. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-117–13-144). National Fire Protection Association.
  • Yu, H.-Z., & Newman, J. S. (2008). Theory of fire extinguishment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-79–2-92). National Fire Protection Association.
  • Zalosh, R. (2008). Explosions. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-93–2-106). National Fire Protection Association.