Skip to content
From Fire Safety Academy Wiki
Revision as of 22:34, 7 November 2026 by Jan (talk | contribs) (NFPA wiki: fact-check corrections (written by Claude Opus 5.5))
Contents
  1. 1Legal basis and scope
  2. 2Hazard classes and divisions
  3. 3Placards, labels and identification numbers
  4. 4Placards in emergency response
  5. 5Regulatory uses of placarding status
  6. 6Relation to NFPA 704 and other markings
  7. 7Limits and common misconceptions
  8. 8See also
  9. 9Notes
  10. 10References

Hazardous materials placarding is the system of diamond-shaped signs fixed to transport vehicles, rail cars and freight containers to show that they carry hazardous materials and to which hazard class those materials belong.[1] Placards are used on bulk packages such as tank cars and cargo tanks, and smaller labels of the same kind on nonbulk packages. Both convey information by colour, symbol, hazard class or division number, and either the class wording or a four-digit identification number.[1] In the United States, placarding is part of the Hazardous Materials Regulations of the U.S. Department of Transportation (DOT), which also cover the marking and labelling of packages and the placarding of railroad cars.[2]

The hazard classes behind the placards are the nine internationally accepted classes for dangerous goods in transport, from explosives (Class 1) to miscellaneous hazardous materials (Class 9).[3] For emergency responders, placards are among the sources used to detect hazardous materials at a road or rail incident. Together with identification numbers and shipping papers, they give access to hazard and response information.[4][5] This article describes the US and Canadian system as presented in the 2008 Fire Protection Handbook.

Legal basis and scope

The DOT defines a hazardous material as a substance or material designated by the Secretary of Transportation as capable of posing an unreasonable risk to health, safety and property in commerce.[3] The definition includes hazardous substances, hazardous wastes, elevated temperature materials, marine pollutants and, internationally, dangerous goods.[3] In the United States, shipments of hazardous chemicals in interstate or foreign commerce by land, water or air must comply with the DOT Hazardous Materials Regulations, as described by Davenport (2008).[2]

Those regulations, as summarised in the 2008 handbook, cover the responsibilities of shippers, the construction of containers, the marking and labelling of packages, and the loading, placarding and movement of railroad cars.[2] They also contain a Table of Hazardous Materials that gives each material its proper shipping name, United Nations (UN) number, hazard class and packing group.[2] For rail, the DOT regulates hazardous material shipments through its Pipeline and Hazardous Materials Safety Administration (PHMSA), and the Federal Railroad Administration (FRA) enforces the rules.[5] In Canada, Transport Canada regulates the shipment of explosives and other dangerous chemicals.[2]

The size of a package decides which markings apply. The handbook defines bulk packaging as any containment system, including transport vehicles and freight containers, that exceeds a set capacity. The limits are an internal volume of 450 L (119 gal) for liquids, 400 kg (882 lb) for solids and a water capacity of 454 kg (1000 lb) for compressed gases.[6] Placards are required on some bulk packages, such as cargo tanks, portable tanks, tank cars and hopper cars, while labels are found on some nonbulk packages.[1]

Hazard classes and divisions

The handbook lists the nine classes with their divisions. It warns that these definitions do not show all the exceptions in the regulations, so they should not be used to determine compliance.[3] The table below summarises the classes, with examples given in the handbook.[7]

The nine transport hazard classes as listed in the 2008 handbook[7]
Class Divisions Examples given in the handbook
1 Explosives and blasting agents 1.1 mass explosion hazard; 1.2 projection hazard; 1.3 fire and minor blast or projection hazard; 1.4 minor explosion hazard; 1.5 very insensitive explosives; 1.6 extremely insensitive explosives Dynamite, TNT, black powder; common fireworks; ammonium nitrate–fuel oil mix
2 Gases 2.1 flammable gases; 2.2 nonflammable, nontoxic gases; 2.3 toxic gases by inhalation Propane, acetylene; carbon dioxide, anhydrous ammonia; arsine, phosgene, chlorine
3 Flammable liquids – Acetone, amyl acetate, gasoline, methyl alcohol
4 Flammable solids and reactive liquids and solids 4.1 flammable solids; 4.2 spontaneously combustible materials; 4.3 dangerous when wet materials Nitrocellulose, matches; phosphorus, aluminium alkyls, charcoal; calcium carbide, potassium
5 Oxidisers and organic peroxides 5.1 oxidisers; 5.2 organic peroxides Ammonium nitrate fertiliser; dibenzoyl peroxide
6 Toxic materials and infectious substances 6.1 toxic materials; 6.2 infectious substances Aniline, arsenic, carbon tetrachloride; anthrax, botulism, tetanus
7 Radioactive materials – Cobalt, uranium hexafluoride
8 Corrosive materials – Hydrochloric acid, sulfuric acid, sodium hydroxide
9 Miscellaneous hazardous materials – Adipic acid, molten sulfur, dry ice, PCBs

Several divisions are defined by measured properties. A flammable gas (Division 2.1) is a gas at 20 °C (68 °F) or less and 101.3 kPa. It must be ignitable in air at 13 % or less by volume, or have a flammable range of at least 12 % in air regardless of the lower limit.[8] A toxic gas (Division 2.3) without adequate human data is presumed toxic if tests on laboratory animals give an LC50 of not more than 5000 ppm.[8] A dangerous-when-wet material (Division 4.3) is one that, in contact with water, can become spontaneously flammable or give off flammable or toxic gas at more than 1 L per kg of material per hour.[8] Poison-inhalation gases are further graded into hazard zones A to D, with LC50 limits of 200, 1000, 3000 and 5000 ppm.[9]

Class 3 is defined by the flash point. The handbook text defines flammable liquids as liquids with a flash point of not more than 60 °C (140 °F).[8] In the United States and Canada, an additional worded class, combustible liquids, covers liquids with flash points above 60 °C (140 °F) and below 93 °C (200 °F). US rules also allow shippers to reclassify liquids with a flash point above 38 °C (100 °F) as combustible liquids.[8]

A worked example shows how this works for two common fuels. Rivkin (2008a) gives the flash point of gasoline as –40 to –46 °C (–40 to –50 °F) and that of No. 2 diesel fuel as 52 °C (125 °F).[10] Gasoline lies far below the 60 °C limit and is a Class 3 flammable liquid. Diesel fuel at 52 °C is also below 60 °C, so under the international definition it is Class 3. Because its flash point is above 38 °C, a US shipper may reclassify it as a combustible liquid.

The rail statistics in the handbook reflect this double status: diesel fuel appears with the class entry "3/CL".[11] For storage, the same table of Rivkin (2008a) gives NFPA 30 Class II for No. 2 diesel fuel and Class IB for gasoline, a classification separate from the transport classes.[10] Combustible liquids, in turn, are an additional worded class added in the United States and Canada, not one of the nine numbered classes.[8]

Placards, labels and identification numbers

Placards measure 273 mm by 273 mm (10.8 in. by 10.8 in.), while labels on packages measure 102 mm by 102 mm (4 in. by 4 in.), or less on cylinders.[1] DOT Chart 12, reproduced in the handbook, shows examples of US and Canadian placards and labels for all nine classes.[1] Some placards are mounted on a square white background to indicate special handling. The handbook lists this for Division 1.1, Division 1.2, Division 2.3, Division 6.1 Packing Group I Zone A and Class 7.[1] A placard reading DANGEROUS indicates a mixed load of several classes of hazardous materials.[1]

The identification number names the material more precisely than the class. Identification numbers are four-digit numbers assigned to a specific hazardous material or group of materials and are used to look up hazard and response information.[4] In transport they must be shown on nonbulk packages, except limited quantities, next to the required labels. On bulk packages such as cargo tanks, portable tanks and tank cars, they appear on an orange panel, in the centre of the placard, or in the centre of a placard-sized white diamond.[4] On shipping papers, the number carries the prefix "UN" for domestic and international shipments or "NA" for shipments regarded as hazardous only within North America.[4] The handbook illustrates the three display forms with the numbers 1075, 1671 and 2020.[4]

On a rail tank car or other rail car, trailer or container, placards may be fixed to both sides and both ends. They alert responders to the presence of a hazardous material and indicate its hazard class.[5] The DOT identification number may also be found on both sides and both ends, and the name of the contents may be stencilled on the sides.[5] For a highway cargo tank vehicle, the inspection guide reproduced by Routhier (2008) shows where the placard and identification number are displayed on an MC 306 cargo tank.[12]

Not every load of hazardous material is placarded. According to the 2008 handbook, transport vehicles and freight containers could contain up to 454 kg (1000 lb) of certain hazardous materials without a placard.[1] Limited-quantity shipments, Division 6.2 infectious substances and ORM-D shipments, a US class for consumer commodities of limited hazard, do not require placards.[1][9] On experimental locomotive sets fuelled with liquefied natural gas (LNG), the LNG tender between two locomotives is not considered to be in commerce and therefore does not need to be placarded.[13]

Placards in emergency response

In Hazardous materials response, detecting the presence of hazardous materials is the first task.[9] C. J. Wright (2008a) lists looking for placards and labels as one of the steps responders take at any emergency, alongside reviewing shipping papers and facility documents.[4][1] During the survey that follows, the name, identification number or placard of each containment system is recorded, because it gives access to the sources of hazard and response information.[14]

One of the two primary printed resources listed in the handbook for that step is the DOT Emergency Response Guidebook.[15] Santis (2008) describes it as covering emergency response procedures for transport incidents with explosives or other hazardous materials. It is normally carried on all hazardous materials transport vehicles and by fire and police departments.[16] The edition cited in the 2008 handbook is ERG2004.[17]

Placards must be read from a safe distance. Because of the orientation of the cars, placards and markings may not be visible, and it may not be prudent to approach close enough to read them; binoculars can help.[5] For highway incidents, Routhier (2008) lists the hazard classes shown by placards, if visible, and the four-digit identification number among the information to obtain when an emergency is reported.[18] A placard does not say whether a tank is loaded or empty; the handbook advises using the shipping papers to determine this.[1] The most common entries on shipping papers are the proper shipping name, hazard class or division, identification number, packing group and total quantity, although not all of them are always present.[19]

Placarding has also been used to grade the response. A 1994 hazardous materials response plan of the Fire Department of the City of New York (FDNY) assigns products to three levels. The plan is reproduced in the National Institute of Standards and Technology (NIST) report on the World Trade Center emergency response.[20] Products for which no DOT placard is required fall in level one and placarded products in level two. Level three is reserved for named materials such as chlorine, anhydrous ammonia, organic peroxides and radioactive materials.[20]

Regulatory uses of placarding status

Whether a vehicle must be placarded also triggers other rules. In the United States, the Federal Motor Carrier Safety Regulations, as described by Routhier (2008), set two minimum levels of fire extinguisher protection. A power unit that does not carry hazardous materials in a quantity requiring marking or placarding needs a 5-B:C extinguisher, or two 4-B:C extinguishers. A 10-B:C extinguisher is required on a power unit used to transport hazardous materials.[21]

The same regulations prohibit smoking while explosives, flammable liquids, gases or solids, or oxidisers that require marking or placarding are loaded, unloaded or transported.[22] The ban also applies while driving an empty tank vehicle that last contained a flammable liquid or gas and was required to be marked or placarded.[22] For placarded vehicles, the rules of the Federal Motor Carrier Safety Administration require the driver to examine each tyre at the start of each trip and each time the vehicle is parked.[22]

Placards and labels also stay in force after delivery. In 1994, the US Occupational Safety and Health Administration (OSHA) required facilities that receive containers marked, labelled or placarded under DOT rules to keep those markings on the container (29 CFR 1910.1201).[23] They must remain until the container is sufficiently cleaned of residue and purged of vapours to remove any potential hazard.[23]

Relation to NFPA 704 and other markings

Transport placarding and the NFPA 704 diamond are separate systems. NFPA 704 markings are used within facilities to show the degree of health, flammability and instability hazard on a scale from 0 to 4. They may appear on nonbulk packages but are not used on transport vehicles.[4][24] Benedetti (2008) names both systems together as the principal means of limiting the impact of large flammable gas fires in populated areas.[25]

The two systems can describe the same material quite differently. Anhydrous ammonia is listed in Division 2.2, nonflammable gas, in the 2005 rail statistics, while its NFPA 704 diamond gives a health rating of 3 and a flammability rating of 1.[11][26] Chlorine is Division 2.3, toxic gas, in transport and carries a health rating of 4 with the oxidiser symbol OX in NFPA 704.[11][27] A placard names a hazard class, whereas the diamond grades three kinds of hazard side by side.

Limits and common misconceptions

The absence of a placard does not mean the absence of hazardous materials. Besides the quantity threshold and the exempt categories described above, Whitford (2008) notes that most pesticides likely to be encountered are not required to be placarded and are not listed in the Emergency Response Guidebook.[28] Placards can also be wrong. Routhier (2008) lists incorrect or missing placarding and identification markings, and missing or incorrect shipping papers, among the hazards to fire fighters at cargo tank incidents.[18]

A placard shows the hazard class, not every hazard. The handbook describes the general hazard properties of each class as "not all-inclusive"; gases, for example, may also be corrosive, asphyxiant or thermally unstable.[7] Multicompartment cargo tanks may carry materials of more than one hazard class at the same time.[18] The DANGEROUS placard for mixed loads does not identify the individual classes at all.[1]

The numbers in the handbook should be read with care. The table of classes gives the Class 3 limit as a flash point below 141 °F (60 °C), while the text gives not more than 140 °F (60 °C).[7][8] The handbook describes US and Canadian rules as they stood around 2007–2008, cites ERG2004, and states that its class definitions should not be used to determine compliance with the regulations.[3][17]

See also

Notes

  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 C. J. Wright (2008a), p. 13-124.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 Davenport (2008), p. 7-54.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 C. J. Wright (2008a), p. 13-118.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 4.6 C. J. Wright (2008a), p. 13-122.
  5. ↑ 5.0 5.1 5.2 5.3 5.4 C. J. Wright (2008b), pp. 21-111–21-112.
  6. ↑ C. J. Wright (2008a), pp. 13-117–13-118.
  7. ↑ 7.0 7.1 7.2 7.3 C. J. Wright (2008a), p. 13-119.
  8. ↑ 8.0 8.1 8.2 8.3 8.4 8.5 8.6 C. J. Wright (2008a), pp. 13-119–13-120.
  9. ↑ 9.0 9.1 9.2 C. J. Wright (2008a), p. 13-121.
  10. ↑ 10.0 10.1 Rivkin (2008a), p. 21-32.
  11. ↑ 11.0 11.1 11.2 C. J. Wright (2008b), p. 21-113.
  12. ↑ Routhier (2008), p. 21-27.
  13. ↑ C. J. Wright (2008b), p. 21-117.
  14. ↑ C. J. Wright (2008a), pp. 13-126–13-127.
  15. ↑ C. J. Wright (2008a), pp. 13-130–13-131.
  16. ↑ Santis (2008), p. 6-251.
  17. ↑ 17.0 17.1 Santis (2008), p. 6-256.
  18. ↑ 18.0 18.1 18.2 Routhier (2008), p. 21-24.
  19. ↑ C. J. Wright (2008a), pp. 13-125–13-126.
  20. ↑ 20.0 20.1 Lawson and Vettori (2005), Appendix A.
  21. ↑ Routhier (2008), p. 21-22.
  22. ↑ 22.0 22.1 22.2 Routhier (2008), p. 21-23.
  23. ↑ 23.0 23.1 Hildebrand and Noll (2008), p. 13-92.
  24. ↑ C. J. Wright (2008a), p. 13-123.
  25. ↑ Benedetti (2008), p. 6-6.
  26. ↑ Lemoff (2008), p. 6-178.
  27. ↑ Lemoff (2008), p. 6-180.
  28. ↑ Whitford (2008), p. 6-240.

References

  • Benedetti, R. P. (2008). Fire hazards of materials. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-3–6-9). National Fire Protection Association.
  • Davenport, J. A. (2008). Storage and handling of chemicals. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-43–7-55). National Fire Protection Association.
  • Hildebrand, M. S., & Noll, G. G. (2008). Public fire protection and hazmat management. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-81–13-98). National Fire Protection Association.
  • Lawson, J. R., & Vettori, R. L. (2005). The emergency response operations (NIST NCSTAR 1-8). National Institute of Standards and Technology.
  • Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
  • Rivkin, C. H. (2008a). Automotive and marine service station operations. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-29–21-40). National Fire Protection Association.
  • Routhier, B. (2008). Fire safety in commercial vehicles. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-15–21-27). National Fire Protection Association.
  • Santis, L. D. (2008). Explosives and blasting agents. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-247–6-256). National Fire Protection Association.
  • Whitford, F. (2008). Pesticides in the workplace. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-233–6-245). National Fire Protection Association.
  • Wright, C. J. (2008a). Managing the response to hazardous material incidents. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-117–13-144). National Fire Protection Association.
  • Wright, C. J. (2008b). Rail transportation systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-109–21-134). National Fire Protection Association.