Skip to content
From Fire Safety Academy Wiki
Peter (talk | contribs)
Add SVG figures fse-laser-fire-hazards-v1.svg, fse-laser-fire-hazards-v2.svg, fse-laser-fire-hazards-v3.svg, fse-laser-fire-hazards-v4.svg (list-3 visual plan)
Mark (talk | contribs)
m Remove source references from image captions
 
Line 5: Line 5:


Every laser has three basic components. The lasing medium is a solid, liquid, gas or semiconductor, for example a ruby or Nd:YAG crystal, carbon dioxide, argon or excimer gases. A pumping system supplies energy by strong light, by an electric current or by chemical reactions. A feedback mechanism, normally a pair of mirrors of which one is partly transparent, returns light through the medium to build up the beam.<ref name="Seeber-8-52-53">Seeber (2008), pp. 8-52–8-53.</ref> Continuous wave lasers deliver a steady beam, while pulsed lasers deliver repeated pulses. In a Q-switched laser a shutter between the mirrors holds back the lasing action and then releases a very intense pulse.<ref name="Seeber-8-53">Seeber (2008), p. 8-53.</ref>
Every laser has three basic components. The lasing medium is a solid, liquid, gas or semiconductor, for example a ruby or Nd:YAG crystal, carbon dioxide, argon or excimer gases. A pumping system supplies energy by strong light, by an electric current or by chemical reactions. A feedback mechanism, normally a pair of mirrors of which one is partly transparent, returns light through the medium to build up the beam.<ref name="Seeber-8-52-53">Seeber (2008), pp. 8-52–8-53.</ref> Continuous wave lasers deliver a steady beam, while pulsed lasers deliver repeated pulses. In a Q-switched laser a shutter between the mirrors holds back the lasing action and then releases a very intense pulse.<ref name="Seeber-8-53">Seeber (2008), p. 8-53.</ref>
[[File:fse-laser-fire-hazards-v1.svg|thumb|upright=1.5|alt=Schematic of a laser: lasing medium between a full mirror and a partly reflecting mirror, pumped by an energy source, emitting a narrow beam|The three basic components of a laser, with a narrow coherent beam leaving through the partly reflecting mirror, compared with a lamp radiating in all directions. Based on Seeber (2008), pp. 8-52–8-53.]]
[[File:fse-laser-fire-hazards-v1.svg|thumb|upright=1.5|alt=Schematic of a laser: lasing medium between a full mirror and a partly reflecting mirror, pumped by an energy source, emitting a narrow beam|The three basic components of a laser, with a narrow coherent beam leaving through the partly reflecting mirror, compared with a lamp radiating in all directions.]]


Lasers are widespread. The handbook lists product code scanners, printers, CD-ROM drives, music and film recording, theme park displays, surgery and veterinary work. It also lists alignment in construction, industrial cutting, welding and drilling of metal, paper and fabric, and research and military uses.<ref name="Seeber-8-51" /> Fire protection itself uses lasers of very low power. The smoke photometer of the cone calorimeter uses a 0.5 mW helium-neon laser.<ref name="MS-2-45">Madrzykowski and Stroup (2008), p. 2-45.</ref><ref name="Babrauskas-3-75">Babrauskas (2002a), p. 3-75.</ref> The 2008 handbook reports some spot-type smoke detectors with a laser beam and up to 100 times the sensitivity of LED units.<ref name="Dungan-14-22">Dungan (2008a), p. 14-22.</ref>
Lasers are widespread. The handbook lists product code scanners, printers, CD-ROM drives, music and film recording, theme park displays, surgery and veterinary work. It also lists alignment in construction, industrial cutting, welding and drilling of metal, paper and fabric, and research and military uses.<ref name="Seeber-8-51" /> Fire protection itself uses lasers of very low power. The smoke photometer of the cone calorimeter uses a 0.5 mW helium-neon laser.<ref name="MS-2-45">Madrzykowski and Stroup (2008), p. 2-45.</ref><ref name="Babrauskas-3-75">Babrauskas (2002a), p. 3-75.</ref> The 2008 handbook reports some spot-type smoke detectors with a laser beam and up to 100 times the sensitivity of LED units.<ref name="Dungan-14-22">Dungan (2008a), p. 14-22.</ref>
Line 28: Line 28:


Under the older system, upper Class 3B lasers in the half-watt range could occasionally be considered a fire hazard.<ref name="Seeber-8-53" /> Embedded lasers are a special case. They contain a higher-class beam, generally Class 4, inside an enclosure with engineering controls, and are classified as Class 1. They keep the same inherent fire risk because of the power of the beam.<ref name="Seeber-8-53" /><ref name="Seeber-8-54" /> The handbook therefore names Class 4 lasers, embedded lasers however classified and some Class 3 lasers as the ones with significant fire safety concerns.<ref name="Seeber-8-55">Seeber (2008), p. 8-55.</ref>
Under the older system, upper Class 3B lasers in the half-watt range could occasionally be considered a fire hazard.<ref name="Seeber-8-53" /> Embedded lasers are a special case. They contain a higher-class beam, generally Class 4, inside an enclosure with engineering controls, and are classified as Class 1. They keep the same inherent fire risk because of the power of the beam.<ref name="Seeber-8-53" /><ref name="Seeber-8-54" /> The handbook therefore names Class 4 lasers, embedded lasers however classified and some Class 3 lasers as the ones with significant fire safety concerns.<ref name="Seeber-8-55">Seeber (2008), p. 8-55.</ref>
[[File:fse-laser-fire-hazards-v2.svg|thumb|upright=1.5|alt=Power scale showing Classes 2, 3R, 3B and 4, with possible fire hazard at upper Class 3B and Class 4|Continuous-wave power limits of laser Classes 2, 3R and 3B and the zone the handbook treats as a fire hazard. Based on Seeber (2008), pp. 8-53–8-55.]]
[[File:fse-laser-fire-hazards-v2.svg|thumb|upright=1.5|alt=Power scale showing Classes 2, 3R, 3B and 4, with possible fire hazard at upper Class 3B and Class 4|Continuous-wave power limits of laser Classes 2, 3R and 3B and the zone the handbook treats as a fire hazard.]]


== How a beam ignites materials ==
== How a beam ignites materials ==
Line 67: Line 67:


As a worked example, take a beam of 0.5 W, the half-watt range in which upper Class 3B lasers can be considered a fire hazard. For illustration, assume it strikes a 0.6 mm diameter spot, equal to the fibre diameter in the case study below. The fibre diameter does not establish the actual spot size on a target.<ref name="Seeber-8-53" /><ref name="Seeber-8-54" />
As a worked example, take a beam of 0.5 W, the half-watt range in which upper Class 3B lasers can be considered a fire hazard. For illustration, assume it strikes a 0.6 mm diameter spot, equal to the fibre diameter in the case study below. The fibre diameter does not establish the actual spot size on a target.<ref name="Seeber-8-53" /><ref name="Seeber-8-54" />
[[File:fse-laser-fire-hazards-v3.svg|thumb|upright=1.5|alt=Log-log chart of beam irradiance against spot diameter for 0.5 W and 1 mW beams, with horizontal lines for critical ignition heat fluxes|Mean irradiance of a 0.5 W and a 1 mW beam against spot diameter, compared with critical ignition heat fluxes of common materials; the worked example is marked at 0.6 mm. Based on Seeber (2008), pp. 8-53–8-54; Budnick et al. (2008), p. 3-159.]]
[[File:fse-laser-fire-hazards-v3.svg|thumb|upright=1.5|alt=Log-log chart of beam irradiance against spot diameter for 0.5 W and 1 mW beams, with horizontal lines for critical ignition heat fluxes|Mean irradiance of a 0.5 W and a 1 mW beam against spot diameter, compared with critical ignition heat fluxes of common materials; the worked example is marked at 0.6 mm.]]


The spot area is π × 0.0006² / 4 = 2.83 × 10<sup>−7</sup> m², so the irradiance is 0.0005 / 2.83 × 10<sup>−7</sup> = about 1,770 kW/m². The handbook lists critical ignition heat fluxes of 16 kW/m² for plywood, 9 to 15 kW/m² for PMMA and 46 kW/m² for polystyrene.<ref name="Budnick-3-159" /> The nominal beam irradiance is about 110 times the plywood value under this spot-size assumption. At a 6.3 mm spot diameter it would equal 16 kW/m². This crossing is not a laser ignition threshold: the table describes uniformly heated specimens with a pilot.
The spot area is π × 0.0006² / 4 = 2.83 × 10<sup>−7</sup> m², so the irradiance is 0.0005 / 2.83 × 10<sup>−7</sup> = about 1,770 kW/m². The handbook lists critical ignition heat fluxes of 16 kW/m² for plywood, 9 to 15 kW/m² for PMMA and 46 kW/m² for polystyrene.<ref name="Budnick-3-159" /> The nominal beam irradiance is about 110 times the plywood value under this spot-size assumption. At a 6.3 mm spot diameter it would equal 16 kW/m². This crossing is not a laser ignition threshold: the table describes uniformly heated specimens with a pilot.
Line 83: Line 83:


The handbook describes a case from 1997 in a hospital in the south-western United States. During a tracheal stenosis procedure, a 0.6 mm laser fibre was passed through a bronchoscope inside an endotracheal tube that was not fire-resistant. The oxygen concentration at the laser was about 100 percent.<ref name="Seeber-8-54" /> Midway through, the surgeon saw a flash of light from a fire in the patient's throat. The tube was blackened inside and the bronchoscope coatings had melted. The fibre had not been stripped and cleaved before use, and ignition near its tip was most likely due to a fracture or a piece of coating lying over the tip.<ref name="Seeber-8-54" />
The handbook describes a case from 1997 in a hospital in the south-western United States. During a tracheal stenosis procedure, a 0.6 mm laser fibre was passed through a bronchoscope inside an endotracheal tube that was not fire-resistant. The oxygen concentration at the laser was about 100 percent.<ref name="Seeber-8-54" /> Midway through, the surgeon saw a flash of light from a fire in the patient's throat. The tube was blackened inside and the bronchoscope coatings had melted. The fibre had not been stripped and cleaved before use, and ignition near its tip was most likely due to a fracture or a piece of coating lying over the tip.<ref name="Seeber-8-54" />
[[File:fse-laser-fire-hazards-v4.svg|thumb|upright=1.5|alt=Cross-section of an endotracheal tube with a bronchoscope and a laser fibre whose tip extends 5 mm, in about 100 percent oxygen|Elements of the 1997 laser airway fire: a non-fire-resistant endotracheal tube, a bronchoscope and a 0.6 mm laser fibre in about 100 percent oxygen. Based on Seeber (2008), p. 8-54; Allen (2008), pp. 6-187 and 6-194.]]
[[File:fse-laser-fire-hazards-v4.svg|thumb|upright=1.5|alt=Cross-section of an endotracheal tube with a bronchoscope and a laser fibre whose tip extends 5 mm, in about 100 percent oxygen|Elements of the 1997 laser airway fire: a non-fire-resistant endotracheal tube, a bronchoscope and a 0.6 mm laser fibre in about 100 percent oxygen.]]


== Hazards of the equipment ==
== Hazards of the equipment ==

Latest revision as of 08:31, 13 November 2026

Laser fire hazards are the ways in which lasers can start or feed a fire, above all through the beam acting as an ignition source.[1][2] The equipment adds hazards of its own, from flammable liquids, flammable or reactive gases and high-voltage parts.[1] A laser concentrates light of a single colour into a narrow, intense beam, which makes it useful for cutting, welding, drilling and surgery but also able to ignite almost any combustible material.[1][3][2] The 20th edition of the US Fire Protection Handbook (2008) states that Class 4 and some Class 3B beams can ignite combustibles in every field of use.[2] Health care needs particular attention, because beams are used close to drapes, tubing and patients, often in an oxygen-enriched atmosphere.[2][4] Control relies on physical measures where possible and, in medicine, mostly on administrative measures under a laser safety officer, with the beam treated like an open flame.[1][2]

Laser light and laser equipment

The word laser is an acronym for "light amplification by stimulated emission of radiation". The radiation is not the ionising radiation of radioactive materials but electromagnetic radiation in the infrared, visible and ultraviolet ranges.[1] This optical spectrum runs from infrared wavelengths of 10−6 to 10−4 m, through visible light of 400 to 700 nm, to ultraviolet of 10 to 400 nm.[3] Laser light differs from ordinary light in three ways. It has a single colour (monochromaticity), it travels in one narrow direction (directionality), and its waves are in phase (coherence), so the light is very intense and diverges little.[3]

Every laser has three basic components. The lasing medium is a solid, liquid, gas or semiconductor, for example a ruby or Nd:YAG crystal, carbon dioxide, argon or excimer gases. A pumping system supplies energy by strong light, by an electric current or by chemical reactions. A feedback mechanism, normally a pair of mirrors of which one is partly transparent, returns light through the medium to build up the beam.[5] Continuous wave lasers deliver a steady beam, while pulsed lasers deliver repeated pulses. In a Q-switched laser a shutter between the mirrors holds back the lasing action and then releases a very intense pulse.[6]

Schematic of a laser: lasing medium between a full mirror and a partly reflecting mirror, pumped by an energy source, emitting a narrow beam
The three basic components of a laser, with a narrow coherent beam leaving through the partly reflecting mirror, compared with a lamp radiating in all directions.

Lasers are widespread. The handbook lists product code scanners, printers, CD-ROM drives, music and film recording, theme park displays, surgery and veterinary work. It also lists alignment in construction, industrial cutting, welding and drilling of metal, paper and fabric, and research and military uses.[1] Fire protection itself uses lasers of very low power. The smoke photometer of the cone calorimeter uses a 0.5 mW helium-neon laser.[7][8] The 2008 handbook reports some spot-type smoke detectors with a laser beam and up to 100 times the sensitivity of LED units.[9]

Hazard classes and fire potential

The American National Standards Institute (ANSI) classifies lasers by the ability of the direct or reflected beam to damage the eye or skin, using the maximum permissible exposure (MPE) as the threshold.[6] The handbook gives both the older classes of ANSI Z136.1 (2000) and the newer system of ANSI Z136.1-2007 and the international standard IEC 60825-1.[6] The classes are therefore defined by injury, not by fire, and the fire potential is noted separately for the higher classes.[10]

Laser classes of ANSI Z136.1-2007 and IEC 60825-1 and their fire potential, as summarised by Seeber (2008)[10]
Class Output power (continuous wave) Main biological hazard Fire potential
1, 1M Not stated None in normal use (1M: only with optical instruments) None stated
2, 2M Up to 1 mW (Class 2), visible Eye, if viewed longer than the blink reflex of 0.25 s None stated
3R 1 to 5 mW, visible Eye, mainly with collecting optics None stated
3B 5 to 500 mW, visible and infrared Eye, even from a momentary direct view Not usually; possible at the upper end of the range
4 Above Class 3B Eye and skin, including diffuse reflections Fire hazard

Under the older system, upper Class 3B lasers in the half-watt range could occasionally be considered a fire hazard.[6] Embedded lasers are a special case. They contain a higher-class beam, generally Class 4, inside an enclosure with engineering controls, and are classified as Class 1. They keep the same inherent fire risk because of the power of the beam.[6][2] The handbook therefore names Class 4 lasers, embedded lasers however classified and some Class 3 lasers as the ones with significant fire safety concerns.[11]

Power scale showing Classes 2, 3R, 3B and 4, with possible fire hazard at upper Class 3B and Class 4
Continuous-wave power limits of laser Classes 2, 3R and 3B and the zone the handbook treats as a fire hazard.

How a beam ignites materials

Laser radiation heats a material by being absorbed at its surface. Solids and liquids usually absorb radiation within a few micrometres, and how much they absorb depends on the wavelength.[12] A solid cannot burn directly: it must first be heated until it pyrolyses and releases combustible gases.[13] These gases ignite only if enough heat is added. The ignition temperature is the lowest temperature at which a substance ignites under specified conditions.[14] A laser beam acts as a concentrated external ignition source of this kind.[2][15]

Two material properties describe how easily a surface is ignited by an incident heat flux. The ignition energy is the heat per unit area that must be absorbed before the material pyrolyses, ignites and burns. It equals the absorbed heat flux multiplied by the exposure time, so a high flux ignites a material faster.[16] For a given material and test configuration, the critical heat flux for ignition is the value at or below which ignition does not occur, however long the exposure.[16] Materials with a low thermal inertia, the product of thermal conductivity, density and heat capacity, heat up quickly at the surface. Polyurethane foam, for example, needs less ignition energy than pine because it cannot conduct heat away from its surface as well.[17]

The ignition temperature itself depends on how fast energy is delivered. For softwoods it rises from about 250 °C for smouldering at around 5 kW/m² to about 360 °C for piloted ignition at around 20 kW/m².[18] In every case, a source can only ignite a fuel if it delivers energy faster than the fuel loses it.[15] This is why the power of a beam and the size of the spot it strikes both matter.

Beam irradiance and a worked example

The irradiance of a beam is its power divided by the area it strikes. For a circular spot of diameter d the mean irradiance follows from the first equation below. To estimate how quickly a thin material ignites, such as a fabric curtain or a sheet of paper, the handbook gives the second equation. It treats the material as a slab that heats uniformly, with no convective losses.[19]

E=Pπd2/4tign=ρscsδ(Tign−TS)q˙′'net

Symbol Description Unit
E Mean irradiance of the beam on the target kW/m²
P Beam power kW
d Diameter of the spot struck by the beam m
tign Time to ignition s
ρs Density of the solid kg/m³
cs Heat capacity of the solid kJ/(kg·°C)
δ Thickness of the thin material (volume divided by exposed area) m
Tign Ignition temperature of the solid °C
TS Initial temperature of the solid °C
q˙′'net Net absorbed heat flux at the surface kW/m²

As a worked example, take a beam of 0.5 W, the half-watt range in which upper Class 3B lasers can be considered a fire hazard. For illustration, assume it strikes a 0.6 mm diameter spot, equal to the fibre diameter in the case study below. The fibre diameter does not establish the actual spot size on a target.[6][2]

Log-log chart of beam irradiance against spot diameter for 0.5 W and 1 mW beams, with horizontal lines for critical ignition heat fluxes
Mean irradiance of a 0.5 W and a 1 mW beam against spot diameter, compared with critical ignition heat fluxes of common materials; the worked example is marked at 0.6 mm.

The spot area is π × 0.0006² / 4 = 2.83 × 10−7 m², so the irradiance is 0.0005 / 2.83 × 10−7 = about 1,770 kW/m². The handbook lists critical ignition heat fluxes of 16 kW/m² for plywood, 9 to 15 kW/m² for PMMA and 46 kW/m² for polystyrene.[19] The nominal beam irradiance is about 110 times the plywood value under this spot-size assumption. At a 6.3 mm spot diameter it would equal 16 kW/m². This crossing is not a laser ignition threshold: the table describes uniformly heated specimens with a pilot.

The handbook's own example is a 1 mm PVC laminate with a density of 1,450 kg/m³, a heat capacity of 0.84 kJ/(kg·°C) and an ignition temperature of 220 °C. Starting at 20 °C and exposed to 50 kW/m², it ignites in about 5 seconds.[19] If the full 1,770 kW/m² were absorbed uniformly by that laminate with no losses, the same equation would give 1,450 × 0.84 × 0.001 × 200 / 1,770 = 0.14 seconds. A beam of 1 mW, the limit of Class 2, has a nominal irradiance of about 3.5 kW/m² on the same assumed spot, below the tabulated critical fluxes under their test conditions.[6][19]

These numbers show orders of magnitude, not predictions. The 0.14-second estimate also assumes complete absorption of the beam and uniform heating of the laminate, conditions that the small spot does not meet. The handbook advises caution because ignition is a complex phenomenon.[19] Critical heat fluxes are measured on test specimens, such as the 100 mm × 100 mm samples of the cone calorimeter, and assume a pilot such as a spark.[19][20] A small spot loses heat to the cooler material around it, so the class-based guidance of the handbook remains the primary criterion.[15][11]

Lasers in oxygen-enriched atmospheres

An oxygen-enriched atmosphere is one with more than 21 percent oxygen by volume, or an oxygen partial pressure above 160 torr (21.3 kPa).[21] Most materials ignite at considerably lower temperatures in such an atmosphere and burn faster once ignited. The higher the oxygen concentration, the less energy is needed for ignition and the faster flames spread.[15] A little pure oxygen can make items that are normally noncombustible in air burn very well.[22]

This is why health care needs particular attention. In a health care occupancy, oxygen-enriched atmospheres occur during practically every inhalation anaesthetic and respiratory therapy procedure.[4] The fires most directly associated with medical gases have involved lasers used near endotracheal tubes that carry those gases.[23] The handbook lists lasers among the ignition sources in hospital oxygen-enriched atmospheres, next to electrosurgical units and fibreoptic light sources. The fuels include drapes, patient hair, rubber gloves, oxygen tubing and masks, gauze, and the intestinal gases hydrogen and methane.[4] Oxygen, nitrous oxide, a wet environment and many electrical ignition sources together make the operating room a particularly hazardous fire location.[24]

Helium-oxygen mixtures are sometimes used in anaesthesia for laser airway surgery and should be treated as oxygen-enriched atmospheres. Helium delays ignition because it conducts heat better than nitrogen. If ignition does occur, however, flames spread faster and burn hotter than in nitrogen, so the fire is more destructive.[25] Patient care in a hyperbaric chamber is another use of an oxygen-enriched atmosphere, with the oxygen percentage deliberately increased.[4]

The handbook describes a case from 1997 in a hospital in the south-western United States. During a tracheal stenosis procedure, a 0.6 mm laser fibre was passed through a bronchoscope inside an endotracheal tube that was not fire-resistant. The oxygen concentration at the laser was about 100 percent.[2] Midway through, the surgeon saw a flash of light from a fire in the patient's throat. The tube was blackened inside and the bronchoscope coatings had melted. The fibre had not been stripped and cleaved before use, and ignition near its tip was most likely due to a fracture or a piece of coating lying over the tip.[2]

Cross-section of an endotracheal tube with a bronchoscope and a laser fibre whose tip extends 5 mm, in about 100 percent oxygen
Elements of the 1997 laser airway fire: a non-fire-resistant endotracheal tube, a bronchoscope and a 0.6 mm laser fibre in about 100 percent oxygen.

Hazards of the equipment

The 2008 handbook calls electrical shock from laser power supplies the most common hazard across laser types. These power supplies can also start fires, like any electrical equipment, and fuses, circuit breakers, insulation, grounding and interlocks control the hazard.[2] Many lasers use capacitors that release large charges very quickly. Shorting or an internal fault can make a capacitor rupture, burn or explode. Capacitors should therefore be enclosed by screens, shields, barriers or uninhabited rooms that also contain fragments, with interlocked covers.[2]

Dye lasers use a fluorescent organic dye dissolved in an organic solvent, often a flammable liquid. Quantities range from about 1 L to 20 L, and larger systems may use hundreds of gallons of solvent. A spill can meet ignition sources in the beam and the electrical parts.[11] Recommended measures include spill containment, suitably rated or intrinsically safe pumps and motors, metal rather than plastic tubing and compression fittings. Liquid level, flow and pressure should be monitored, ventilation checked and remote shutdown provided, and larger systems are protected like any industrial process with large quantities of flammable liquids.[11]

Some lasers, for example excimer lasers, use flammable or reactive gases, pure or mixed with an inert gas. The smallest workable quantity and concentration should be used, stored outside the building or in a ventilated gas cabinet.[11] Combustible gas detectors set to alarm at 25 percent of the lower flammable limit should be considered. Exhaust vents should be kept away from air intakes, and emergency shutdown should be possible at the gas supply and from a remote point.[11] In a semiconductor fabrication facility, laser radiation is one of several radiation hazards. The process machines should carry appropriate safety devices and follow the SEMI recommendations for cleanroom equipment.[26]

Control measures

Some precautions against beam ignition are engineering controls, but most are administrative. They are directed by a laser safety officer (LSO), a person trained in laser hazards and fire safety, and only staff trained by the LSO should operate the lasers.[2][11] Typical measures are standard operating procedures, warning signs and personal protective equipment. Before use, the beam intensity profile and alignment should be checked, suitable beam stops placed, and materials next to the beam kept noncombustible.[2] Users and maintenance work should be logged, and the manufacturer's recommendations followed.[11]

Before a laser that is a fire hazard is used, staff should know the exits, emergency shutdown buttons, shutdown and notification procedures, and where the extinguishers are and how to use them. Responding firefighters should be told about the hazards.[11] In hospital oxygen-enriched atmospheres, fire prevention builds in redundant safeguards, so that no fire occurs even if one element fails or is omitted.[4]

If oxygen-saturated bedding or clothing ignites, flame spread is extremely rapid. The 2008 handbook calls for large quantities of water and says dry chemical extinguishers and fire blankets are ineffective. It also describes halon and carbon dioxide extinguishers as appropriate. If electrical equipment is involved, it must be de-energised before water is applied.[4]

The handbook lists NFPA 115, Standard for Laser Fire Protection, together with NFPA 99 and ANSI Z136.3-2005 for lasers in health care facilities.[27] NUREG-1805, a 2004 guide for the fire protection inspection programme of the US Nuclear Regulatory Commission, lists the 1999 edition of NFPA 115 as a recommended practice.[28] These are US documents. The handbook mentions a database of laser fire incidents kept by the NFPA Technical Committee on Laser Fire Protection, but gives no statistics from it.[2]

Limits and common misconceptions

A low class number does not always mean a low fire risk. An embedded laser may be labelled Class 1 while it contains a Class 4 beam that can ignite materials.[2] The classes are based on eye and skin injury, so a laser that is safe to look at under its class rules is not necessarily safe near combustibles.[6] The handbook also warns that, except for some metals, no material is "fire safe" around lasers, and that flammable anaesthetic gases are still used in research in the United States and some other countries.[2]

Air is not the only atmosphere to consider. Materials that resist ignition in air may ignite readily in an oxygen-enriched atmosphere.[15][22] Helium in a breathing mixture delays ignition, but does not prevent a more destructive fire.[25] Finally, the beam is not the only hazard: electrical faults, capacitors, solvents and gases can start fires without the beam being involved.[2][11]

See also

Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 Seeber (2008), p. 8-51.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 Seeber (2008), p. 8-54.
  3. ↑ 3.0 3.1 3.2 Seeber (2008), p. 8-52.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 Allen (2008), p. 6-194.
  5. ↑ Seeber (2008), pp. 8-52–8-53.
  6. ↑ 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 Seeber (2008), p. 8-53.
  7. ↑ Madrzykowski and Stroup (2008), p. 2-45.
  8. ↑ Babrauskas (2002a), p. 3-75.
  9. ↑ Dungan (2008a), p. 14-22.
  10. ↑ 10.0 10.1 Seeber (2008), pp. 8-53–8-54.
  11. ↑ 11.00 11.01 11.02 11.03 11.04 11.05 11.06 11.07 11.08 11.09 Seeber (2008), p. 8-55.
  12. ↑ Van Rossum (2027), §5.4.
  13. ↑ Van Rossum (2027), §4.1.
  14. ↑ Van Rossum (2027), §4.2.
  15. ↑ 15.0 15.1 15.2 15.3 15.4 Rosales and Stoltzfus (2008), p. 9-227.
  16. ↑ 16.0 16.1 Madrzykowski and Stroup (2008), p. 2-34.
  17. ↑ Madrzykowski and Stroup (2008), pp. 2-34–2-35.
  18. ↑ Madrzykowski and Stroup (2008), p. 2-35.
  19. ↑ 19.0 19.1 19.2 19.3 19.4 19.5 Budnick et al. (2008), p. 3-159.
  20. ↑ Babrauskas (2002a), p. 3-68.
  21. ↑ Rosales and Stoltzfus (2008), p. 9-225.
  22. ↑ 22.0 22.1 Allen (2008), p. 6-188.
  23. ↑ Allen (2008), p. 6-187.
  24. ↑ Allen (2008), p. 6-190.
  25. ↑ 25.0 25.1 Allen (2008), p. 6-191.
  26. ↑ DeGiorgio and Peterkin (2008), p. 9-128.
  27. ↑ Seeber (2008), pp. 8-55–8-56.
  28. ↑ Iqbal and Salley (2004), p. E-4.

References

  • Allen, M. (2008). Medical gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-187–6-196). National Fire Protection Association.
  • Babrauskas, V. (2002a). The cone calorimeter. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-63–3-81). National Fire Protection Association; Society of Fire Protection Engineers.
  • Budnick, E. K., Hunt, S. P., & Wright, M. T. (2008). Closed form enclosure fire calculations. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-145–3-166). National Fire Protection Association.
  • DeGiorgio, V., & Peterkin, H. (2008). Semiconductor manufacturing. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-119–9-129). National Fire Protection Association.
  • Dungan, K. W. (2008a). Automatic fire detectors. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-15–14-28). National Fire Protection Association.
  • Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
  • Madrzykowski, D., & Stroup, D. W. (2008). Flammability hazard of materials. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-31–2-48). National Fire Protection Association.
  • Rosales, K., & Stoltzfus, J. M. (2008). Oxygen-Enriched atmospheres. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-225–9-243). National Fire Protection Association.
  • Seeber, F. P. (2008). Lasers. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-51–8-56). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.