Skip to content
From Fire Safety Academy Wiki
Jan (talk | contribs)
New FSE wiki article: Boiler furnace explosion (written by Claude Opus 5.5)
 
Jan (talk | contribs)
NFPA wiki: fact-check corrections (written by Claude Opus 5.5)
Line 1: Line 1:
A '''boiler furnace explosion''' is the ignition of an accumulated mixture of fuel and air inside the furnace, gas passes or ducts of a fuel-fired boiler. It is a [[Deflagration]] on the fire side of the boiler, and differs from a boiler explosion, in which the pressure vessel holding the water and steam bursts. The ''Fire Protection Handbook'' (2008) states that such an explosion occurs when an ignition source contacts a combustible mixture of fuel and air. A mixture accumulated in a large confined space can cause a very damaging explosion.<ref name="MA-10-101">Mattern et al. (2008), p. 10-101.</ref>
A '''boiler furnace explosion''' is the ignition of a combustible mixture of fuel and air that has accumulated in the furnace of a fuel-fired boiler or in its associated pipes and ducts.<ref name="MA-10-101" /> In an unvented enclosure such an ignition usually results in a [[Deflagration]].<ref name="ZA-3-406" /> It differs from the boiler explosions of the nineteenth century, which followed a failure to keep water in fire-tube boilers.<ref name="MA-10-91" /> The ''Fire Protection Handbook'' (2008) states that such an explosion occurs when an ignition source contacts a combustible mixture of fuel and air. A mixture accumulated in a large confined space can cause a very damaging explosion.<ref name="MA-10-101">Mattern et al. (2008), p. 10-101.</ref>


The usual causes are a temporary loss of flame, fuel-rich firing, fuel leaking into an idle furnace and the failure to purge between unsuccessful attempts to light a burner.<ref name="MA-10-101" /> Large water-tube boilers are especially exposed: the handbook links their growth in size to the possibility of catastrophic furnace explosions.<ref name="MA-10-92">Mattern et al. (2008), pp. 10-91–10-92.</ref> In the United States, NFPA 85, ''Boiler and Combustion Systems Hazards Code'', addresses these hazards.<ref name="SH-9-184">Sheridan (2008), p. 9-184.</ref> The handbook describes the prevention methods of this code and of US practice as they stood around 2007 and 2008: purging, minimum airflow, flame detection at each burner, burner management systems and trained operators.
The usual causes are a temporary loss of flame, fuel-rich firing, fuel leaking into an idle furnace and the failure to purge between unsuccessful attempts to light a burner.<ref name="MA-10-101" /> Large water-tube boilers are especially exposed: the handbook links their growth in size to the possibility of catastrophic furnace explosions.<ref name="MA-10-92">Mattern et al. (2008), pp. 10-91–10-92.</ref> In the United States, NFPA 85, ''Boiler and Combustion Systems Hazards Code'', addresses these hazards.<ref name="SH-9-184">Sheridan (2008), p. 9-184.</ref> The handbook describes the prevention methods of this code and of US practice as they stood around 2007 and 2008: purging, minimum airflow, flame detection at each burner, burner management systems and trained operators.
Line 6: Line 6:
Early boilers consisted of a furnace for burning the fuel and a separate vessel heated from beneath. In a fire-tube boiler the furnace is a large central horizontal tube surrounded by water, and the hot gases return through tubes that cross the water space.<ref name="MA-10-91">Mattern et al. (2008), p. 10-91.</ref> Failure to keep water in fire-tube boilers caused catastrophic boiler explosions and many deaths in the mid-nineteenth century. The boiler explosion and fire on the steamship SS ''Sultana'' on the Mississippi River on 27 April 1865 killed 1547 people.<ref name="MA-10-91" /> In a table of the deadliest US fire and explosion events by Hall and Cote it ranks second, after the World Trade Center attack of 2001.<ref name="HC-3-10">Hall and Cote (2008), p. 3-10.</ref> The founding of the Steam Boiler Assurance Company in the United Kingdom in 1859 marked the beginning of boiler inspection and insurance.<ref name="MA-10-91" />
Early boilers consisted of a furnace for burning the fuel and a separate vessel heated from beneath. In a fire-tube boiler the furnace is a large central horizontal tube surrounded by water, and the hot gases return through tubes that cross the water space.<ref name="MA-10-91">Mattern et al. (2008), p. 10-91.</ref> Failure to keep water in fire-tube boilers caused catastrophic boiler explosions and many deaths in the mid-nineteenth century. The boiler explosion and fire on the steamship SS ''Sultana'' on the Mississippi River on 27 April 1865 killed 1547 people.<ref name="MA-10-91" /> In a table of the deadliest US fire and explosion events by Hall and Cote it ranks second, after the World Trade Center attack of 2001.<ref name="HC-3-10">Hall and Cote (2008), p. 3-10.</ref> The founding of the Steam Boiler Assurance Company in the United Kingdom in 1859 marked the beginning of boiler inspection and insurance.<ref name="MA-10-91" />


The water-tube boiler, with water inside the tubes and hot gas outside, improved boiler safety, although single tubes could still burst. With pulverised coal firing, water-tube boilers grew to an enormous size, and that size created the possibility of catastrophic furnace explosions.<ref name="MA-10-92" /> Better design, materials, instruments, operator training and supervision, promoted by the American Society of Mechanical Engineers, insurers, NFPA and authorities, have greatly reduced both fire-tube boiler explosions and water-tube furnace explosions.<ref name="MA-10-92" /> A boiler furnace explosion is therefore a combustion event, whereas a classic boiler explosion is the mechanical failure of a pressure vessel. In heating boilers the two can interact: an explosion of unburned fuel in the combustion chamber, or overpressure, can rupture fuel lines and feed a following fire.<ref name="GW-10-19">Gore Willse (2008a), pp. 10-19–10-20.</ref>
The water-tube boiler, with water inside the tubes and hot gas outside, improved boiler safety, although single tubes could still burst. With pulverised coal firing, water-tube boilers grew to an enormous size, and that size created the possibility of catastrophic furnace explosions.<ref name="MA-10-92" /> Better design, materials, instruments, operator training and supervision, promoted by the American Society of Mechanical Engineers, insurers, NFPA and authorities, have greatly reduced both fire-tube boiler explosions and water-tube furnace explosions.<ref name="MA-10-92" /> In the handbook's account, the classic boiler explosions followed a failure to keep water in fire-tube boilers, whereas furnace explosions are the ignition of fuel-air mixtures in the furnace.<ref name="MA-10-91" /><ref name="MA-10-101" /> In heating boilers the two can interact: an explosion of unburned fuel in the combustion chamber, or overpressure, can rupture fuel lines and feed a following fire.<ref name="GW-10-19">Gore Willse (2008a), pp. 10-19–10-20.</ref>


== Mechanism ==
== Mechanism ==
Zalosh describes the general sequence for gas and vapour explosions. Fuel and oxidant mix within the flammable range in a confined space before an ignition source appears. After ignition the flame spreads through the mixture, and the confinement stops the combustion products from expanding freely, so the pressure rises rapidly.<ref name="ZA-3-402">Zalosh (2002), p. 3-402.</ref> ''Introduction to Fire Safety Engineering'' describes the same conditions for a smoke gas explosion in a building. Flammable gases from decomposition or [[Incomplete combustion]] are fairly well premixed with air between the lower and upper explosion limits, and are ignited by autoignition or by a spark or glowing particles.<ref name="VR-4.10">Van Rossum (2027), §4.10.</ref> A boiler furnace provides all three conditions whenever fuel enters without burning at once.
Zalosh describes the general sequence for gas and vapour explosions. Fuel and oxidant mix within the flammable range in a confined space before an ignition source appears. After ignition the flame spreads through the mixture, and the confinement stops the combustion products from expanding freely, so the pressure rises rapidly.<ref name="ZA-3-402">Zalosh (2002), p. 3-402.</ref> ''Introduction to Fire Safety Engineering'' describes the same conditions for a smoke gas explosion in a building. Flammable gases from decomposition or [[Incomplete combustion]] are fairly well premixed with air between the lower and upper explosion limits, and are ignited by autoignition or by a spark or glowing particles.<ref name="VR-4.10">Van Rossum (2027), §4.10.</ref> In a boiler furnace these conditions arise when ignition is lost while fuel and air keep entering.<ref name="MA-10-92b" />


In normal firing the mixture is controlled. The handbook names the "three Ts" of combustion as time, set by furnace size, temperature and turbulence, and adds a fourth factor, continuity: fuel, air and an ignition source must be supplied without interruption.<ref name="MA-10-92b">Mattern et al. (2008), p. 10-92.</ref> The fuel-to-air ratio must also stay within a narrow range, so that the flame of the fuel just burned ignites the fuel just entering. If the fuel is interrupted for a few seconds, the airflow suddenly increases or the burner fails to hold the flame, ignition can be lost and "the controlled flammable mixture becomes an uncontrolled explosive mixture".<ref name="MA-10-92b" /> The authors conclude that a large boiler furnace is always just a few seconds away from catastrophe. Large furnace explosions are remarkably rare only because of the skill of the people and safety systems involved.<ref name="MA-10-92b" />
In normal firing the mixture is controlled. The handbook names the "three Ts" of combustion as time, set by furnace size, temperature and turbulence, and adds a fourth factor, continuity: fuel, air and an ignition source must be supplied without interruption.<ref name="MA-10-92b">Mattern et al. (2008), p. 10-92.</ref> The fuel-to-air ratio must also stay within a narrow range, so that the flame of the fuel just burned ignites the fuel just entering. If the fuel is interrupted for a few seconds, the airflow suddenly increases or the burner fails to hold the flame, ignition can be lost and "the controlled flammable mixture becomes an uncontrolled explosive mixture".<ref name="MA-10-92b" /> The authors conclude that a large boiler furnace is always just a few seconds away from catastrophe. Large furnace explosions are remarkably rare only because of the skill of the people and safety systems involved.<ref name="MA-10-92b" />


Once a mixture has formed, ignition is almost certain. Even a minute ignition source can start a substantial explosion, and a furnace contains many, such as static electricity, hot slag and glowing fly ash in a hopper. Safe operation must therefore focus on never creating a large combustible mixture rather than on removing ignition sources.<ref name="MA-10-101" /> A US Nuclear Regulatory Commission guide notes that most turbulent premixed flames occur in engineered combustion systems such as boilers, furnaces and process heaters.<ref name="IS-3-12">Iqbal and Salley (2004), p. 3-12.</ref>
Ignition sources abound in a furnace, such as static electricity, hot slag and glowing fly ash in a hopper, and even a minute one might initiate a substantial explosion. Safe operation must therefore focus on never creating a large combustible mixture rather than on removing ignition sources.<ref name="MA-10-101" /> A US Nuclear Regulatory Commission guide notes that most turbulent premixed flames occur in engineered combustion systems such as boilers, furnaces and process heaters.<ref name="IS-3-12">Iqbal and Salley (2004), p. 3-12.</ref>


== Causes ==
== Causes ==
The handbook lists several typical routes to an explosive accumulation. A temporary loss of flame from an interruption of fuel, air or ignition energy lets fuel and air collect before ignition is re-established, and any momentary fuel-rich operation can do the same. Leaking fuel can evaporate in an idle furnace and ignite explosively when the first burner is lit.<ref name="MA-10-101" /> In units with several burners, the undetected loss of flame at one burner can let a mixture accumulate somewhere in the furnace, where other burners then ignite it.<ref name="MA-10-101" /> Sheridan gives the same picture for power station boilers. An uneven or low fuel flow can cause loss of flame in part of the boiler, and the raw fuel that continues to enter is ignited by another burner or a hot surface.<ref name="SH-9-184" />
The handbook lists several typical routes to an explosive accumulation. A temporary loss of flame from an interruption of fuel, air or ignition energy lets fuel and air collect before ignition is re-established, and any momentary fuel-rich operation can do the same. Leaking fuel can evaporate in an idle furnace and ignite explosively when the first burner is lit.<ref name="MA-10-101" /> In units with several burners, the undetected loss of flame at one burner can let a mixture accumulate somewhere in the furnace, where other burners then ignite it.<ref name="MA-10-101" /> Sheridan gives the same picture for power station boilers. An uneven or low fuel flow can cause loss of flame in part of the boiler, and the raw fuel that continues to enter is ignited by another burner or a hot surface.<ref name="SH-9-184" />


Operator error is the second main source. The classic example is failing to purge the furnace between repeated unsuccessful attempts to light a burner. Another is ignoring small explosions, or "puffs", that do no damage but can signal a serious defect.<ref name="MA-10-101" /> Within the furnace the air-fuel ratio can change severely without any visible sign at the burners or stack. Combustion controls that raise the fuel input when steam pressure falls are dangerous unless interlocked against fuel-rich firing and loss of ignition.<ref name="MA-10-102">Mattern et al. (2008), p. 10-102.</ref>
Operator error is the second main source. The classic example is failing to purge the furnace between repeated unsuccessful attempts to light a burner. Another is ignoring small explosions, or "puffs", that do no damage but can signal a serious defect.<ref name="MA-10-101" /> Within the furnace the air-fuel ratio can change severely without any visible sign at the burners or stack. Combustion controls that raise the fuel input when steam flow or pressure falls are potentially dangerous unless protected or interlocked against a fuel-rich mixture and loss of ignition.<ref name="MA-10-102">Mattern et al. (2008), p. 10-102.</ref>


Each fuel adds its own failure modes. Heavy oils must be heated to the viscosity needed for atomisation, but oil heated too far can vapour-bind the pump and interrupt the flow. Wet atomising steam causes pulsations, and both faults can lead to loss of ignition.<ref name="MA-10-94">Mattern et al. (2008), p. 10-94.</ref> Mixing oils of different viscosity in one tank, wear of atomiser orifices, burners running fuel-rich and burner tips left out after maintenance can all produce unburned fuel in the furnace.<ref name="MA-10-101" />
Each fuel adds its own failure modes. Heavy oils must be heated to the viscosity needed for atomisation, but oil heated too far can vapour-bind the pump and interrupt the flow. Wet atomising steam causes pulsations, and both faults can lead to loss of ignition.<ref name="MA-10-94">Mattern et al. (2008), p. 10-94.</ref> Mixing oils of different viscosity in one tank, wear of atomiser orifices, burners running fuel-rich and burner tips left out after maintenance can all produce unburned fuel in the furnace.<ref name="MA-10-101" />
Line 26: Line 26:
Pulverised coal is the most demanding case. A large boiler may burn 45.4 kg (100 lb) of coal per second, yet as little as 0.05 kg/m³ of coal in air forms an explosive mixture. A momentary flameout therefore produces an explosive mixture very quickly, and methane released from freshly crushed coal can also collect in bunkers, pulverisers and burner piping.<ref name="MA-10-102" />
Pulverised coal is the most demanding case. A large boiler may burn 45.4 kg (100 lb) of coal per second, yet as little as 0.05 kg/m³ of coal in air forms an explosive mixture. A momentary flameout therefore produces an explosive mixture very quickly, and methane released from freshly crushed coal can also collect in bunkers, pulverisers and burner piping.<ref name="MA-10-102" />


Low-NOx firing, which stages combustion with a fuel-rich zone near the burner, can reduce the safety margins against unburned fuel. It also tends to leave smouldering carbon-rich ash in horizontal ducts and hoppers as a hidden ignition source.<ref name="MA-10-103">Mattern et al. (2008), p. 10-103.</ref> In fluidised bed boilers the hot bed allows firing at up to four times the normal fuel-to-air ratio, and fuel accumulated in the bed can heat it rapidly and might lead to a furnace explosion.<ref name="MA-10-100">Mattern et al. (2008), p. 10-100.</ref> Starting main fuel before the bed has reached its proven temperature can also cause an explosion.<ref name="MA-10-103" />
Low-NOx firing, which stages combustion with a fuel-rich zone near the burner,<ref name="MA-10-92b" /> can reduce the safety margins against unburned fuel. It also tends to leave smouldering carbon-rich ash in horizontal ducts and hoppers as a hidden ignition source.<ref name="MA-10-103">Mattern et al. (2008), p. 10-103.</ref> In fluidised bed boilers the hot bed allows firing at up to four times the normal fuel-to-air ratio, and fuel accumulated in the bed can heat it rapidly and might lead to a furnace explosion.<ref name="MA-10-100">Mattern et al. (2008), p. 10-100.</ref> Starting main fuel before the bed has reached its proven temperature can also cause an explosion.<ref name="MA-10-103" />


== Pressure and consequences ==
== Pressure and consequences ==
Line 54: Line 54:
As a worked example, take natural gas as methane, whose stoichiometric volume fraction is 0.095.<ref name="ZA-3-406" /> A methane fraction of 5 % gives an equivalence ratio of 0.05 × 0.905 / (0.095 × 0.95) ≈ 0.50, the value that Zalosh associates with the lower flammable limit. In theory even this lean mixture would develop about 6 atm absolute if it filled a closed space, roughly 5 bar above atmospheric pressure, although measured values near the limit are lower. A second example uses the coal values of the handbook. At 45.4 kg/s, one second of flameout supplies enough coal to bring 45.4 / 0.05 ≈ 910 m³ of air to the explosive concentration of 0.05 kg/m³, and five seconds about 4500 m³.<ref name="MA-10-102" /> These numbers show why the handbook speaks of seconds, and why the purge and flame-detection rules aim to stop fuel before a large volume can form.
As a worked example, take natural gas as methane, whose stoichiometric volume fraction is 0.095.<ref name="ZA-3-406" /> A methane fraction of 5 % gives an equivalence ratio of 0.05 × 0.905 / (0.095 × 0.95) ≈ 0.50, the value that Zalosh associates with the lower flammable limit. In theory even this lean mixture would develop about 6 atm absolute if it filled a closed space, roughly 5 bar above atmospheric pressure, although measured values near the limit are lower. A second example uses the coal values of the handbook. At 45.4 kg/s, one second of flameout supplies enough coal to bring 45.4 / 0.05 ≈ 910 m³ of air to the explosive concentration of 0.05 kg/m³, and five seconds about 4500 m³.<ref name="MA-10-102" /> These numbers show why the handbook speaks of seconds, and why the purge and flame-detection rules aim to stop fuel before a large volume can form.


The financial consequences match these pressures. A database of Marsh Risk Consulting, cited by Sheridan, recorded eight boiler explosions between 1977 and 1996. Their average property damage was $53.75 million each, in 2007 US dollars, and forced outages occurred at a rate of about one per year.<ref name="SH-9-184" /> Mattern and co-authors put the cost of a major boiler explosion, including replacement power, at up to $100 million.<ref name="MA-10-104">Mattern et al. (2008), pp. 10-103–10-104.</ref> Sheridan adds that numerous puffs with minor damage have undoubtedly occurred as well.<ref name="SH-9-184" />
The financial consequences match these pressures. A database of Marsh Risk Consulting, cited by Sheridan, recorded eight boiler-furnace explosions between 1977 and 1996. Their average property damage was $53.75 million each, in 2007 US dollars, and forced outages occurred at a rate of about one per year.<ref name="SH-9-184" /> Mattern and co-authors put the cost of a major boiler explosion, including replacement power, at up to $100 million.<ref name="MA-10-104">Mattern et al. (2008), pp. 10-103–10-104.</ref> Sheridan adds that numerous puffs with minor damage have undoubtedly occurred as well.<ref name="SH-9-184" />


== Prevention ==
== Prevention ==
Furnace explosions in large water-tube boilers in the 1960s led to the codification of the open-register light-off and continuous purge procedure for all fuels.<ref name="MA-10-103" /> It keeps the airflow at or above a minimum of 25 % of the full-load mass airflow during all operation of the boiler. The handbook notes that NFPA 8502, the predecessor of NFPA 85 for multiple-burner boilers, specified a volumetric airflow rate until its 1995 edition.<ref name="MA-10-103" /> The procedure rests on three conditions: as few equipment manipulations as possible, a fuel-rich condition at each burner during light-off, and a very air-rich furnace during light-off and warm-up.<ref name="MA-10-103" />
Furnace explosions in large water-tube boilers in the 1960s led to the codification of the open-register light-off and continuous purge procedure for all fuels.<ref name="MA-10-103" /> It keeps the airflow at or above a minimum of 25 % of the full-load mass airflow during all operation of the boiler. The handbook notes that NFPA 8502, the predecessor of NFPA 85 for multiple-burner boilers, specified a volumetric airflow rate until its 1995 edition.<ref name="MA-10-103" /> The procedure rests on three conditions: as few equipment manipulations as possible, a fuel-rich condition at each burner during light-off, and a very air-rich furnace during light-off and warm-up.<ref name="MA-10-103" />


In its simplest form, as described in the 2008 handbook, the burner air registers are set to a fixed open position and the furnace is purged in that position. The total purge airflow must be between 25 % and 40 % of full-load mass airflow, and the first burner or group of burners is lit without changing the airflow or the register positions.<ref name="MA-10-103" /> Proposals to reduce airflow below 25 % for better NOx control and low-load efficiency had not been accepted by the NFPA committee, because no tests showed that this could be done safely.<ref name="MA-10-103" /> The same 25 % limit applies to the turndown of oil burners, which sets a practical floor to the load range.<ref name="MA-10-94" />
In its simplest form, as described in the 2008 handbook, the burner air registers are set to a fixed open position and the furnace is purged in that position. The total purge airflow must be between 25 % and 40 % of full-load mass airflow, and the first burner or group of burners is lit without changing the airflow or the register positions.<ref name="MA-10-103" /> Proposals to reduce airflow below 25 % for better NOx control and low-load efficiency had not been accepted by the NFPA committee, because no tests showed that this could be done safely.<ref name="MA-10-103" /> Because total airflow must not fall below 25 % of the full-capacity rate (the purge rate), the very high turndown that steam atomisers can reach is inconsistent with high efficiency.<ref name="MA-10-94" />


Flame supervision is the second line. A means of flame detection is needed at each pulverised coal burner, and the main flame must be distinguishable from the igniter flame.<ref name="MA-10-99">Mattern et al. (2008), p. 10-99.</ref> Each [[Flame safeguard]] works within a burner management system that sequences the burner and fuel supply; bypassing such systems shifts the burden to operators who may not be able to watch every component.<ref name="MA-10-101" /> A system of interlocks should prevent improper sequencing and shut the boiler down after critical malfunctions. New boilers should not be fired until the safeguards are installed and tested, and bypassing interlocks with jumpers should never be allowed.<ref name="MA-10-104b">Mattern et al. (2008), p. 10-104.</ref> In fluidised beds, where flame detectors are not useful, in-bed thermocouples prove the bed temperature instead.<ref name="MA-10-103" />
Flame supervision is the second line. A means of flame detection is needed at each pulverised coal burner, and the main flame must be distinguishable from the igniter flame.<ref name="MA-10-99">Mattern et al. (2008), p. 10-99.</ref> Each [[Flame safeguard]] works within a burner management system that sequences the burner and fuel supply; bypassing such systems shifts the burden to operators who may not be able to watch every component.<ref name="MA-10-101" /> A system of interlocks should prevent improper sequencing and shut the boiler down after critical malfunctions. New boilers should not be fired until the safeguards are installed and tested, and bypassing interlocks with jumpers should never be allowed.<ref name="MA-10-104b">Mattern et al. (2008), p. 10-104.</ref> In fluidised beds, where flame detectors are not useful, in-bed thermocouples prove the bed temperature instead.<ref name="MA-10-103" />


Fuel systems and people complete the protection. Gas-fired systems need positive means to stop gas leaking into an idle burner, vents upstream of the last shutoff valve and provisions for tightness tests of the safety shutoff valves.<ref name="MA-10-98">Mattern et al. (2008), p. 10-98.</ref> The handbook states that safe operation cannot be ensured by equipment design alone and calls for competent, periodically retrained operators. Where operator error caused a serious accident, inadequate training was often the root cause.<ref name="MA-10-104b" /> Reliable carbon monoxide analysers can warn of fuel-rich or poorly mixed conditions in the furnace.<ref name="MA-10-103" /> Small boilers below 3,663 kW (12,500,000 Btu/h), often installed inside existing buildings, should stand in a separate room, preferably of noncombustible construction.<ref name="MA-10-104b" />
Fuel systems and people complete the protection. Gas-fired systems need positive means to stop gas leaking into an idle furnace, vents upstream of the last shutoff valve and provisions for tightness tests of the safety shutoff valves.<ref name="MA-10-98">Mattern et al. (2008), p. 10-98.</ref> The handbook states that safe operation cannot be ensured by equipment design alone and calls for competent, periodically retrained operators. Where operator error caused a serious accident, inadequate training was often the root cause.<ref name="MA-10-104b" /> Reliable carbon monoxide analysers can warn of fuel-rich or poorly mixed conditions in the furnace.<ref name="MA-10-103" /> Small boilers below 3,663 kW (12,500,000 Btu/h), often installed inside existing buildings, should stand in a separate room, preferably of noncombustible construction.<ref name="MA-10-104b" />


== Related hazards ==
== Related hazards ==
Several other boiler hazards are often confused with furnace explosions. Pulveriser fires and explosions arise from burning fuel fed from the bunkers or from spontaneous combustion in the pulveriser or piping. The handbook's procedure removes the pulveriser from service without emptying it, to avoid creating a sudden air-rich explosive mixture.<ref name="MA-10-102" /> Burner front fires occur when oil released from the fuel or ignition system ignites on the hot outer face of the boiler and can extend several storeys up its face.<ref name="SH-9-184" /> The NFPA technical committee on boiler combustion system hazards also addresses furnace implosions, and heat recovery steam generators with supplementary firing have had a number of serious accidents.<ref name="SH-9-184" /><ref name="MA-10-93">Mattern et al. (2008), p. 10-93.</ref> Fire protection of these exposures in power plants is described under [[Power station fire protection]].
Several other boiler hazards are related to furnace explosions. Pulveriser fires and explosions arise from burning fuel fed from the bunkers or from spontaneous combustion in the pulveriser or piping. The handbook's procedure removes the pulveriser from service without emptying it, to avoid creating a sudden air-rich explosive mixture.<ref name="MA-10-102" /> Burner front fires occur when oil released from the fuel or ignition system ignites on the hot outer face of the boiler and can extend several storeys up its face.<ref name="SH-9-184" /> The NFPA technical committee on boiler combustion system hazards also addresses furnace implosions, and heat recovery steam generators with supplementary firing have had a number of serious accidents.<ref name="SH-9-184" /><ref name="MA-10-93">Mattern et al. (2008), p. 10-93.</ref> Fire protection of these exposures in power plants is described under [[Power station fire protection]].


The same mechanism threatens smaller fuel-fired equipment. An [[Industrial oven and furnace]] shares the hazards of unburned fuel during lighting off, firing and shutdown, and dryers use the same flame failure protection and preventilation.<ref name="OS-8-76">Ostrowski (2008a), p. 8-76.</ref><ref name="OS-8-91">Ostrowski (2008a), p. 8-91.</ref> Gore Willse states that controls against the discharge of unburned fuel or improper fuel-air mixtures are required for all fuel burners, whatever their size.<ref name="GW-10-17">Gore Willse (2008a), p. 10-17.</ref>
The same mechanism threatens smaller fuel-fired equipment. An [[Industrial oven and furnace]] shares the hazards of unburned fuel during lighting off, firing and shutdown, and dryers use the same flame failure protection and preventilation.<ref name="OS-8-76">Ostrowski (2008a), p. 8-76.</ref><ref name="OS-8-91">Ostrowski (2008a), p. 8-91.</ref> Gore Willse states that controls against the discharge of unburned fuel or improper fuel-air mixtures are required for all fuel burners, whatever their size.<ref name="GW-10-17">Gore Willse (2008a), p. 10-17.</ref>

Revision as of 22:29, 7 November 2026

A boiler furnace explosion is the ignition of a combustible mixture of fuel and air that has accumulated in the furnace of a fuel-fired boiler or in its associated pipes and ducts.[1] In an unvented enclosure such an ignition usually results in a Deflagration.[2] It differs from the boiler explosions of the nineteenth century, which followed a failure to keep water in fire-tube boilers.[3] The Fire Protection Handbook (2008) states that such an explosion occurs when an ignition source contacts a combustible mixture of fuel and air. A mixture accumulated in a large confined space can cause a very damaging explosion.[1]

The usual causes are a temporary loss of flame, fuel-rich firing, fuel leaking into an idle furnace and the failure to purge between unsuccessful attempts to light a burner.[1] Large water-tube boilers are especially exposed: the handbook links their growth in size to the possibility of catastrophic furnace explosions.[4] In the United States, NFPA 85, Boiler and Combustion Systems Hazards Code, addresses these hazards.[5] The handbook describes the prevention methods of this code and of US practice as they stood around 2007 and 2008: purging, minimum airflow, flame detection at each burner, burner management systems and trained operators.

Boiler explosions and furnace explosions

Early boilers consisted of a furnace for burning the fuel and a separate vessel heated from beneath. In a fire-tube boiler the furnace is a large central horizontal tube surrounded by water, and the hot gases return through tubes that cross the water space.[3] Failure to keep water in fire-tube boilers caused catastrophic boiler explosions and many deaths in the mid-nineteenth century. The boiler explosion and fire on the steamship SS Sultana on the Mississippi River on 27 April 1865 killed 1547 people.[3] In a table of the deadliest US fire and explosion events by Hall and Cote it ranks second, after the World Trade Center attack of 2001.[6] The founding of the Steam Boiler Assurance Company in the United Kingdom in 1859 marked the beginning of boiler inspection and insurance.[3]

The water-tube boiler, with water inside the tubes and hot gas outside, improved boiler safety, although single tubes could still burst. With pulverised coal firing, water-tube boilers grew to an enormous size, and that size created the possibility of catastrophic furnace explosions.[4] Better design, materials, instruments, operator training and supervision, promoted by the American Society of Mechanical Engineers, insurers, NFPA and authorities, have greatly reduced both fire-tube boiler explosions and water-tube furnace explosions.[4] In the handbook's account, the classic boiler explosions followed a failure to keep water in fire-tube boilers, whereas furnace explosions are the ignition of fuel-air mixtures in the furnace.[3][1] In heating boilers the two can interact: an explosion of unburned fuel in the combustion chamber, or overpressure, can rupture fuel lines and feed a following fire.[7]

Mechanism

Zalosh describes the general sequence for gas and vapour explosions. Fuel and oxidant mix within the flammable range in a confined space before an ignition source appears. After ignition the flame spreads through the mixture, and the confinement stops the combustion products from expanding freely, so the pressure rises rapidly.[8] Introduction to Fire Safety Engineering describes the same conditions for a smoke gas explosion in a building. Flammable gases from decomposition or Incomplete combustion are fairly well premixed with air between the lower and upper explosion limits, and are ignited by autoignition or by a spark or glowing particles.[9] In a boiler furnace these conditions arise when ignition is lost while fuel and air keep entering.[10]

In normal firing the mixture is controlled. The handbook names the "three Ts" of combustion as time, set by furnace size, temperature and turbulence, and adds a fourth factor, continuity: fuel, air and an ignition source must be supplied without interruption.[10] The fuel-to-air ratio must also stay within a narrow range, so that the flame of the fuel just burned ignites the fuel just entering. If the fuel is interrupted for a few seconds, the airflow suddenly increases or the burner fails to hold the flame, ignition can be lost and "the controlled flammable mixture becomes an uncontrolled explosive mixture".[10] The authors conclude that a large boiler furnace is always just a few seconds away from catastrophe. Large furnace explosions are remarkably rare only because of the skill of the people and safety systems involved.[10]

Ignition sources abound in a furnace, such as static electricity, hot slag and glowing fly ash in a hopper, and even a minute one might initiate a substantial explosion. Safe operation must therefore focus on never creating a large combustible mixture rather than on removing ignition sources.[1] A US Nuclear Regulatory Commission guide notes that most turbulent premixed flames occur in engineered combustion systems such as boilers, furnaces and process heaters.[11]

Causes

The handbook lists several typical routes to an explosive accumulation. A temporary loss of flame from an interruption of fuel, air or ignition energy lets fuel and air collect before ignition is re-established, and any momentary fuel-rich operation can do the same. Leaking fuel can evaporate in an idle furnace and ignite explosively when the first burner is lit.[1] In units with several burners, the undetected loss of flame at one burner can let a mixture accumulate somewhere in the furnace, where other burners then ignite it.[1] Sheridan gives the same picture for power station boilers. An uneven or low fuel flow can cause loss of flame in part of the boiler, and the raw fuel that continues to enter is ignited by another burner or a hot surface.[5]

Operator error is the second main source. The classic example is failing to purge the furnace between repeated unsuccessful attempts to light a burner. Another is ignoring small explosions, or "puffs", that do no damage but can signal a serious defect.[1] Within the furnace the air-fuel ratio can change severely without any visible sign at the burners or stack. Combustion controls that raise the fuel input when steam flow or pressure falls are potentially dangerous unless protected or interlocked against a fuel-rich mixture and loss of ignition.[12]

Each fuel adds its own failure modes. Heavy oils must be heated to the viscosity needed for atomisation, but oil heated too far can vapour-bind the pump and interrupt the flow. Wet atomising steam causes pulsations, and both faults can lead to loss of ignition.[13] Mixing oils of different viscosity in one tank, wear of atomiser orifices, burners running fuel-rich and burner tips left out after maintenance can all produce unburned fuel in the furnace.[1]

Design of the Fuel oil system therefore aims at a steady fuel flow and places burner shutoff valves close to the burner, so that little oil can drain into the furnace after a trip.[14] Gas leaks are invisible and may not be heard over plant noise. Wet gas carrying liquid fuel into the burners can cause a momentary surge in fuel input or a flameout followed by reignition and explosion.[12]

Pulverised coal is the most demanding case. A large boiler may burn 45.4 kg (100 lb) of coal per second, yet as little as 0.05 kg/m³ of coal in air forms an explosive mixture. A momentary flameout therefore produces an explosive mixture very quickly, and methane released from freshly crushed coal can also collect in bunkers, pulverisers and burner piping.[12]

Low-NOx firing, which stages combustion with a fuel-rich zone near the burner,[10] can reduce the safety margins against unburned fuel. It also tends to leave smouldering carbon-rich ash in horizontal ducts and hoppers as a hidden ignition source.[15] In fluidised bed boilers the hot bed allows firing at up to four times the normal fuel-to-air ratio, and fuel accumulated in the bed can heat it rapidly and might lead to a furnace explosion.[16] Starting main fuel before the bed has reached its proven temperature can also cause an explosion.[15]

Pressure and consequences

The pressure of a deflagration in a closed space follows from the ideal gas law applied before and after combustion. Zalosh gives the ratio of final to initial pressure as the ratio of the products of mole number and temperature of the burned and unburned gas. The mixture strength is expressed as the equivalence ratio, the actual fuel-to-air ratio divided by the stoichiometric one, which can be written in terms of the fuel volume fraction.[2]

PmP0=nbTbn0T0 ϕ=x(1−xst)xst(1−x)

Symbol Description Unit
Pm Pressure at the end of a closed-vessel deflagration Pa (absolute)
P0 Initial pressure in the enclosure Pa (absolute)
nb, n0 Moles of burned gas at the end, and of gas-air mixture at the start mol
Tb, T0 Temperature of the burned gas, and initial temperature of the mixture K
ϕ Fuel equivalence ratio –
x, xst Fuel volume fraction, and stoichiometric fuel volume fraction –

The equation applies when the flame has spread through the whole unvented enclosure, and assuming adiabatic combustion at constant volume gives conservative estimates. Zalosh's calculations give worst-case values of 8 to 9.6 atm absolute for methane, propane and hydrogen in air at equivalence ratios of 1.1 to 1.2. Near the lower flammable limit, at an equivalence ratio of 0.5, methane and propane still give about 6 to 6.5 atm absolute.[2] Measured closed-vessel pressures agree well with theory near stoichiometric mixtures but are significantly lower near the flammable limits.[2] Measured maximum pressures for ten of twelve gases and vapours lie between 6.8 and 8.1 bar gauge.[17]

As a worked example, take natural gas as methane, whose stoichiometric volume fraction is 0.095.[2] A methane fraction of 5 % gives an equivalence ratio of 0.05 × 0.905 / (0.095 × 0.95) ≈ 0.50, the value that Zalosh associates with the lower flammable limit. In theory even this lean mixture would develop about 6 atm absolute if it filled a closed space, roughly 5 bar above atmospheric pressure, although measured values near the limit are lower. A second example uses the coal values of the handbook. At 45.4 kg/s, one second of flameout supplies enough coal to bring 45.4 / 0.05 ≈ 910 m³ of air to the explosive concentration of 0.05 kg/m³, and five seconds about 4500 m³.[12] These numbers show why the handbook speaks of seconds, and why the purge and flame-detection rules aim to stop fuel before a large volume can form.

The financial consequences match these pressures. A database of Marsh Risk Consulting, cited by Sheridan, recorded eight boiler-furnace explosions between 1977 and 1996. Their average property damage was $53.75 million each, in 2007 US dollars, and forced outages occurred at a rate of about one per year.[5] Mattern and co-authors put the cost of a major boiler explosion, including replacement power, at up to $100 million.[18] Sheridan adds that numerous puffs with minor damage have undoubtedly occurred as well.[5]

Prevention

Furnace explosions in large water-tube boilers in the 1960s led to the codification of the open-register light-off and continuous purge procedure for all fuels.[15] It keeps the airflow at or above a minimum of 25 % of the full-load mass airflow during all operation of the boiler. The handbook notes that NFPA 8502, the predecessor of NFPA 85 for multiple-burner boilers, specified a volumetric airflow rate until its 1995 edition.[15] The procedure rests on three conditions: as few equipment manipulations as possible, a fuel-rich condition at each burner during light-off, and a very air-rich furnace during light-off and warm-up.[15]

In its simplest form, as described in the 2008 handbook, the burner air registers are set to a fixed open position and the furnace is purged in that position. The total purge airflow must be between 25 % and 40 % of full-load mass airflow, and the first burner or group of burners is lit without changing the airflow or the register positions.[15] Proposals to reduce airflow below 25 % for better NOx control and low-load efficiency had not been accepted by the NFPA committee, because no tests showed that this could be done safely.[15] Because total airflow must not fall below 25 % of the full-capacity rate (the purge rate), the very high turndown that steam atomisers can reach is inconsistent with high efficiency.[13]

Flame supervision is the second line. A means of flame detection is needed at each pulverised coal burner, and the main flame must be distinguishable from the igniter flame.[19] Each Flame safeguard works within a burner management system that sequences the burner and fuel supply; bypassing such systems shifts the burden to operators who may not be able to watch every component.[1] A system of interlocks should prevent improper sequencing and shut the boiler down after critical malfunctions. New boilers should not be fired until the safeguards are installed and tested, and bypassing interlocks with jumpers should never be allowed.[20] In fluidised beds, where flame detectors are not useful, in-bed thermocouples prove the bed temperature instead.[15]

Fuel systems and people complete the protection. Gas-fired systems need positive means to stop gas leaking into an idle furnace, vents upstream of the last shutoff valve and provisions for tightness tests of the safety shutoff valves.[21] The handbook states that safe operation cannot be ensured by equipment design alone and calls for competent, periodically retrained operators. Where operator error caused a serious accident, inadequate training was often the root cause.[20] Reliable carbon monoxide analysers can warn of fuel-rich or poorly mixed conditions in the furnace.[15] Small boilers below 3,663 kW (12,500,000 Btu/h), often installed inside existing buildings, should stand in a separate room, preferably of noncombustible construction.[20]

Related hazards

Several other boiler hazards are related to furnace explosions. Pulveriser fires and explosions arise from burning fuel fed from the bunkers or from spontaneous combustion in the pulveriser or piping. The handbook's procedure removes the pulveriser from service without emptying it, to avoid creating a sudden air-rich explosive mixture.[12] Burner front fires occur when oil released from the fuel or ignition system ignites on the hot outer face of the boiler and can extend several storeys up its face.[5] The NFPA technical committee on boiler combustion system hazards also addresses furnace implosions, and heat recovery steam generators with supplementary firing have had a number of serious accidents.[5][22] Fire protection of these exposures in power plants is described under Power station fire protection.

The same mechanism threatens smaller fuel-fired equipment. An Industrial oven and furnace shares the hazards of unburned fuel during lighting off, firing and shutdown, and dryers use the same flame failure protection and preventilation.[23][24] Gore Willse states that controls against the discharge of unburned fuel or improper fuel-air mixtures are required for all fuel burners, whatever their size.[25]

See also

Notes

  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 Mattern et al. (2008), p. 10-101.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 Zalosh (2002), p. 3-406.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 Mattern et al. (2008), p. 10-91.
  4. ↑ 4.0 4.1 4.2 Mattern et al. (2008), pp. 10-91–10-92.
  5. ↑ 5.0 5.1 5.2 5.3 5.4 5.5 Sheridan (2008), p. 9-184.
  6. ↑ Hall and Cote (2008), p. 3-10.
  7. ↑ Gore Willse (2008a), pp. 10-19–10-20.
  8. ↑ Zalosh (2002), p. 3-402.
  9. ↑ Van Rossum (2027), §4.10.
  10. ↑ 10.0 10.1 10.2 10.3 10.4 Mattern et al. (2008), p. 10-92.
  11. ↑ Iqbal and Salley (2004), p. 3-12.
  12. ↑ 12.0 12.1 12.2 12.3 12.4 Mattern et al. (2008), p. 10-102.
  13. ↑ 13.0 13.1 Mattern et al. (2008), p. 10-94.
  14. ↑ Mattern et al. (2008), p. 10-96.
  15. ↑ 15.0 15.1 15.2 15.3 15.4 15.5 15.6 15.7 15.8 Mattern et al. (2008), p. 10-103.
  16. ↑ Mattern et al. (2008), p. 10-100.
  17. ↑ Zalosh (2002), p. 3-407.
  18. ↑ Mattern et al. (2008), pp. 10-103–10-104.
  19. ↑ Mattern et al. (2008), p. 10-99.
  20. ↑ 20.0 20.1 20.2 Mattern et al. (2008), p. 10-104.
  21. ↑ Mattern et al. (2008), p. 10-98.
  22. ↑ Mattern et al. (2008), p. 10-93.
  23. ↑ Ostrowski (2008a), p. 8-76.
  24. ↑ Ostrowski (2008a), p. 8-91.
  25. ↑ Gore Willse (2008a), p. 10-17.

References

  • Gore Willse, P. J. (2008a). Heating systems and appliances. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 10-9–10-56). National Fire Protection Association.
  • Hall, J. R., Jr., & Cote, A. E. (2008). An overview of the fire problem and fire protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-3–3-30). National Fire Protection Association.
  • Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
  • Mattern, L. J., Catania, E., & Ehrlich, S. (2008). Boiler furnaces. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 10-91–10-104). National Fire Protection Association.
  • Ostrowski, R. (2008a). Industrial and commercial heat utilization equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-71–8-92). National Fire Protection Association.
  • Sheridan, D. J. (2008). Electric generating plants. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-179–9-189). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
  • Zalosh, R. (2002). Explosion protection. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-402–3-421). National Fire Protection Association; Society of Fire Protection Engineers.