Contents
- 1Generation, wetting and application
- 2What additives change and what remains
- 3Heat absorption and delivery to the fuel
- 4Expansion, drainage and stability
- 5Proportioning and operating range
- 6Application method and useful delivery
- 7Performance evidence and continuing condition
- 8Protection objectives and limits of performance
- 9See also
- 10Notes
- 11References
Compressed air foam is firefighting foam generated by injecting pressurised air into a flowing foam solution before the discharge device. The Fire Protection Handbook distinguishes this from arrangements that aspirate air at or near the nozzle. Mixing continues as the combined flow travels through hose or piping.[1]
The method can be used with equipment carried on fire apparatus and has been associated particularly with Class A foam applications. It changes how the bubble structure is produced and transported, while the foam proportioner separately establishes the concentrate percentage in the solution.[2]
The resulting fire stream must still deliver useful agent to the target. Use in wildland fire suppression or another operation depends on the fuel, formulation and complete equipment arrangement. The presence of compressed air does not by itself establish a superior extinguishing rating or suitability for every liquid and solid fuel.[3][1]
Generation, wetting and application
The system combines three inputs: water, foam concentrate and compressed air. The first two form the solution; the third expands that solution into foam. The handbook describes the momentum and mixing of the streams within the hose or pipe as part of generation. Air is therefore already present upstream of the outlet, unlike conventional nozzle aspiration.[1]
This distinction does not remove the proportioning requirement. An appropriate air supply cannot correct an unsuitable concentrate percentage or incompatible formulation. Water supply, concentrate delivery and air injection have to operate as a coordinated arrangement. The final foam characteristics depend on the combined process, not merely the nominal capacity of the compressor.[4]
The handbook describes mobile systems primarily associated with Class A applications and also separately designed Class B arrangements. The latter depend on their own agent and performance evidence. A conclusion about one application cannot automatically be transferred to the other. The distinction preserves the relationship between generation method and the particular extinguishing task.[1]
The produced foam still faces losses and delivery constraints. Drainage, heat, disruption and the route to the target affect how much useful water or blanket reaches the hazard. The SFPE foam discussion explains why physical properties require interpretation in relation to fire performance. Compressed-air generation is consequently one part of a specified system, rather than a universal performance claim.[5][6]
What additives change and what remains
An additive can change selected properties of water without removing every limitation of water-based suppression. Wetting agents reduce surface tension and can improve spreading and penetration into some porous combustible materials. Foaming concentrates allow air-filled bubbles to form from an aqueous solution. Other formulations can affect flow or freezing behaviour. These are different purposes, even where one commercial formulation has several characteristics.[7]
Improved wetting can help the solution reach small openings that plain water would bridge. This is relevant to materials with concealed or deep-seated burning. The advantage depends on the fuel and the application, however, and is not equivalent to the tested vapour-sealing performance of a liquid-fire foam. The handbook explicitly distinguishes wetting agents, foams derived from wetting agents and other foam formulations.[8]
Compatibility remains part of the assessment. The solution must suit the delivery equipment, the protected material and the intended concentration. The handbook cautions against mixing formulations from different sources or combining wetting agents and foam concentrates without an established basis. Its foam discussion likewise requires matched proportioning and discharge equipment. A beneficial ingredient property does not establish the performance of every mixture or system.[9][10]
Water reactivity, conductivity and contaminated runoff remain relevant after an additive is introduced. A solution that spreads more readily can also penetrate equipment or carry contamination elsewhere. The handbook therefore considers environmental consequences alongside extinguishing performance. Product-specific evidence is needed to assess those consequences; historical descriptions of an additive as harmless or biodegradable cannot establish the acceptability of every discharge or formulation.[11][12]
Heat absorption and delivery to the fuel
Water absorbs energy as its temperature increases and as liquid changes into vapour. This gives it substantial cooling capacity, but that capacity is useful only where heat transfer actually occurs. Water passing through a fire without sufficient heating does not realise its full theoretical capacity. A heat-balance calculation therefore describes a potential contribution rather than an automatic prediction of extinguishment.[13]
For ordinary solid fuels, cooling the burning surface can reduce the generation of combustible vapour. Water can also cool the surrounding gases and reduce heat transferred back to the fuel. The relative importance of these effects depends on the fire and the application method. The handbook distinguishes direct fuel cooling from the effects of droplets and steam within the surrounding hot environment.[13]
Droplet size creates a trade-off between heat transfer and penetration. Fine droplets provide more surface area for a given water volume and can exchange heat rapidly. They can also evaporate or be carried away before reaching a hot surface. Larger droplets or more coherent streams can penetrate more effectively, while presenting less surface area for heat transfer. The favourable balance therefore changes with plume strength, distance and the intended target.[14]
The amount discharged from a nozzle is consequently different from the amount delivered to the burning material. Obstructions, upward gas motion and evaporation can reduce useful delivery. The handbook uses the distinction between actual delivered density and required delivered density when discussing suppression research. For a manual stream, the same physical distinction explains why an adequate pump flow alone cannot establish that the required cooling reaches the fire.[14]
Expansion, drainage and stability
Expansion describes how much finished foam is produced from a given volume of solution. It is distinct from the proportion of concentrate in that solution. A solution can be correctly proportioned but poorly aerated, or well expanded while containing an unsuitable concentrate percentage. The handbook treats proportioning, foam generation and distribution as separate operations because each affects the final result.[15][5]
Drainage describes liquid leaving the bubble structure over time. As liquid drains, the properties of the remaining foam change, affecting spreading and persistence. The handbook identifies the time for a specified fraction to drain as one measure used in foam evaluation. That measurement concerns a physical characteristic under test conditions, rather than a direct universal measure of extinguishing ability.[16]
More expansion is not automatically better. The SFPE discussion of early film-forming foam development describes a compromise between spreading, drainage and bubble stability. A stiff foam can resist flowing around obstructions, while a very wet foam can lose liquid rapidly. The appropriate characteristics depend on whether the task is surface coverage, retention, penetration into a solid fuel or filling a volume.[17][18]
The generating conditions therefore belong with any reported foam property. Concentrate identity, water quality, pressure, discharge device and air source can all affect the produced foam. High-expansion systems are particularly sensitive to the conditions of the air used for generation. The handbook describes reduced production and stability where hot, contaminated fire gases enter the generator, illustrating why a nominal expansion value is not sufficient by itself.[19]
Proportioning and operating range
Proportioning establishes the concentrate fraction in the water-based solution. The handbook distinguishes systems that draw concentrate using a low-pressure region from systems that inject it using a pump or pressure head. Both must deliver the intended ratio under the relevant operating conditions. The proportioner is consequently matched to the concentrate, water supply and downstream discharge equipment.[10]
A venturi eductor uses the flowing water's pressure energy to create a region into which concentrate is drawn. Its performance depends on inlet conditions and the resistance downstream. Hose length, elevation and the discharge device can therefore affect the resulting mixture. The handbook's discussion of in-line eductors makes this dependence explicit, rather than treating the metering setting alone as evidence of correct proportioning.[20]
Balanced-pressure and bladder arrangements establish the concentrate supply differently. Their useful operating range still has limits, particularly at low water flows. The handbook identifies the possibility of under-proportioning before a bladder arrangement reaches its approved flow range. Higher concentrate viscosity can increase losses in the concentrate piping and affect that limit. These issues are especially relevant when only a small number of closed sprinklers initially operate.[21]
The mixture also affects available operating time. Too little concentrate can produce unsuitable foam, while excessive concentrate consumes the stored supply more rapidly. Verification therefore measures the delivered concentration under representative conditions, rather than relying only on the quantity originally placed in the tank. The handbook treats concentration testing as evidence about the proportioning system and distinguishes it from expansion and drainage measurements.[22]
Application method and useful delivery
Foam can be delivered through hand-held devices, monitors, fixed outlets and sprinkler arrangements. These methods differ in reach, aeration, distribution and dependence on operator positioning. The handbook therefore treats the discharge equipment as part of the tested system. Substituting a different nozzle can change foam quality and coverage even when the solution concentration remains the same.[23]
For liquid surfaces, gentle application can reduce disruption and mixing of foam with fuel. Fixed tank outlets and discharge devices are designed around that requirement and the tank geometry. A monitor operating from outside the hazard must additionally overcome wind, fire updrafts and limitations in positioning. The amount leaving the device can consequently exceed the amount that reaches and remains on the intended surface.[24]
Application rate describes solution delivered per unit area per unit time. It is not the same as the volume of expanded foam occupying that area. A successful application has to overcome foam destruction and leave a protective layer. The handbook relates the required rate to fuel, foam and application method, and presents test-based guidance rather than a single rate applicable to every liquid fire.[25]
High-expansion filling introduces a different delivery problem. The system has to build and retain sufficient foam volume while allowing displaced air to leave. Openings, foam collapse, obstruction and the effects of other water discharges can influence the rate of accumulation. The handbook consequently connects generation capacity with enclosure geometry and the time available to cover the hazard, instead of using expansion ratio alone as the design criterion.[1]
Performance evidence and continuing condition
Foam performance has a strong experimental basis. The SFPE chapter explains that physical properties and small-scale measurements do not always correlate directly with extinguishment in a particular fire test. A test result therefore needs its fuel, scale, equipment and application conditions. A generic claim of good expansion or rapid spreading cannot replace evidence for the intended protection arrangement.[5]
The handbook distinguishes measurements of concentration, expansion, drainage and discharge pattern. These observations address different parts of foam production and application. Concentration examines proportioning; expansion examines incorporation of air; drainage examines changes in the bubble structure. The complete assessment relates these properties to the tested agent and equipment combination rather than selecting one favourable measurement as proof of all-round performance.[16]
Stored concentrate can change through contamination, extreme temperatures or separation. Pumps, valves and small openings can also deteriorate or become obstructed. The handbook consequently treats concentrate surveillance and equipment inspection as separate continuing tasks. Testing arrangements can sometimes assess components without distributing foam over the hazard, but the recorded scope needs to identify which functions were actually demonstrated.[16]
Changes to the protected use can invalidate a previously suitable system. A different fuel, altered storage height or revised discharge route can change the conditions supporting the original test evidence. The IFEG lifecycle framework connects alterations with review of the fire engineering assessment. This makes maintaining the design basis part of continuing protection, alongside maintaining the physical condition of tanks, proportioners and outlets.[26][27]
Protection objectives and limits of performance
Suppression describes an intended change in a fire, but the required outcome needs further definition. Control can limit growth or reduce the rate of heat release without extinguishing every burning item. Extinguishment removes the continuing combustion under the conditions considered. Prevention of renewed burning may require cooling, continued agent retention or removal of an ignition source. These outcomes impose different demands on the protection arrangement.[13][28]
Agent selection follows the fuel and the objective. Water can cool a solid surface, foam can maintain a barrier over a liquid, and a gaseous agent can change the atmosphere surrounding a fire. None of these descriptions establishes universal effectiveness. The protected material, fire geometry, ventilation and available delivery arrangement determine whether the relevant mechanism can operate where it is needed.[29][30]
The assessment also distinguishes successful operation from unsuccessful or delayed operation. An explicit example appears in Australia's Fire Safety Verification Method Standard, 2022 edition. Its structural-stability scenario considers failures of suppression, delayed fire brigade intervention and combinations of failures. That requirement belongs to the Australian method and its stated scenario. It illustrates why the mere presence of equipment is insufficient evidence of the building's performance.[31]
The protection claim consequently includes its conditions of use. These include the hazard, the quantity and distribution of agent, the expected activation sequence and the time for which protection is maintained. Changes to storage, ventilation or operating procedures can alter those conditions. The International Fire Engineering Guidelines connect continued building use and alterations with review of the original engineering assumptions.[26]
See also
Notes
- ↑ 1.0 1.1 1.2 1.3 1.4 Cote et al. (2008), chapter 17.4, p. 17-67.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-50, 17-67.
- ↑ Cote et al. (2008), chapter 17.3, pp. 17-36–17-38.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-50–17-52, 17-67.
- ↑ 5.0 5.1 5.2 Scheffey (2002), pp. 4-88–4-90.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-46, 17-67.
- ↑ Cote et al. (2008), chapter 17.3, pp. 17-36–17-38, 17-42–17-43.
- ↑ Cote et al. (2008), chapter 17.3, pp. 17-36–17-37.
- ↑ Cote et al. (2008), chapter 17.3, p. 17-37.
- ↑ 10.0 10.1 Cote et al. (2008), chapter 17.4, pp. 17-50–17-52.
- ↑ Cote et al. (2008), chapter 17.3, pp. 17-36–17-38, 17-43.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-68–17-69.
- ↑ 13.0 13.1 13.2 Cote et al. (2008), chapter 17.3, pp. 17-32–17-33.
- ↑ 14.0 14.1 Cote et al. (2008), chapter 17.3, p. 17-33.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-49–17-50.
- ↑ 16.0 16.1 16.2 Cote et al. (2008), chapter 17.4, p. 17-68.
- ↑ Scheffey (2002), pp. 4-89–4-90.
- ↑ Cote et al. (2008), chapter 17.4, p. 17-48.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-48–17-50, 17-67.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-50–17-51.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-51–17-52.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-50, 17-68.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-59–17-61, 17-64.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-49, 17-60–17-61.
- ↑ Cote et al. (2008), chapter 17.4, p. 17-49.
- ↑ 26.0 26.1 National Research Council of Canada et al. (2005), §0.3.2.6–0.3.2.8; pp. 0.3-6–0.3-7.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-64, 17-68.
- ↑ Cote et al. (2008), chapter 17.6, pp. 17-119–17-121.
- ↑ Cote et al. (2008), chapter 17.3, pp. 17-32–17-33, 17-36–17-38.
- ↑ Cote et al. (2008), chapter 17.4, pp. 17-45–17-49.
- ↑ Australian Building Codes Board (2022), §2.12.2; p. 19.
References
- Australian Building Codes Board. (2022). Fire Safety Verification Method Standard 2022.
- Cote, A. E., Grant, C. C., Hall, J. R., Jr., & Solomon, R. E. (Eds.). (2008). Fire Protection Handbook (20th ed.). National Fire Protection Association.
- National Research Council of Canada, International Code Council, Department of Building and Housing, & Australian Building Codes Board. (2005). International Fire Engineering Guidelines (2005 ed.). Australian Building Codes Board.
- Scheffey, J. L. (2002). Foam agents and AFFF system design considerations. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall, Jr., & J. M. Watts, Jr. (Eds.), SFPE Handbook of Fire Protection Engineering (3rd ed., chapter 4-4, pp. 4-88–4-122). National Fire Protection Association.