Skip to content
From Fire Safety Academy Wiki
Revision as of 02:48, 8 November 2026 by Mark (talk | contribs) (FSE wiki: fact-check: scope escape risk and historical counts, distinguish Cerro Grande homes from structures, correct smoke uncertainty and suppression-line limits (written by Claude Opus 5.5))
Contents
  1. 1Purposes and ecological basis
  2. 2Fuel policy and research in the United States
  3. 3Fire behaviour and burning conditions
  4. 4Deliberate ignition and control lines
  5. 5Escaped prescribed fires
  6. 6Smoke
  7. 7Recording in fire statistics
  8. 8Terminology in fire safety engineering
  9. 9See also
  10. 10Notes
  11. 11References

Prescribed fire, also called prescribed burning, is the deliberate use of fire by land managers to burn vegetation in a planned area under chosen burning conditions. The aim is to reduce the fuel that feeds a wildfire and to meet forestry and range management goals such as tree growth and wildlife habitat.[1][2] In the United States, federal and state agencies have treated millions of acres with prescribed fire and mechanical means, such as cutting and clearing, to reduce the fire risk.[3] The NFPA Fire Protection Handbook (20th edition, 2008) describes a continuing debate over how much prescribed fire to use, where, when and at what cost.[3] One serious risk is escape: in 2000 a prescribed burn planned for about 360 ha (900 acres) near Los Alamos, New Mexico, spread over about 19,300 ha (47,650 acres) and destroyed 235 homes.[2][4] Prescribed fires also produce smoke, and research into smoke management and public acceptance of "good fire" accompanies their use.[1]

Purposes and ecological basis

Fire research programmes in the United States and Canada share two goals: reducing losses from wildfires, and introducing prescribed fire to achieve forest and range management objectives at reduced cost.[5] US research on fire effects, use and ecology studies how, when and where prescribed fire can improve tree growth, provide better wildlife habitat, reduce fire hazard and meet other forestry goals. This includes the biological response of soils and the effect on stand structure.[1] Canadian research on prescribed fire covers tree damage and mortality, slash removal, seedbed preparation, vegetation control, the design of prescriptions and operational techniques.[1]

The case for reducing fuels rests on the state of many forests. In a 2004 presentation quoted in the handbook, the chief of the USDA Forest Service described many fire-dependent ecosystems in the United States as overgrown and unhealthy. In his view, the proper response is to reduce fuels before large fires break out, through thinning and the effective and safe reintroduction of fire.[6] Long-term ecosystem changes have altered natural fuel beds, so that severe wildfires now burn outside natural fire regimes.[7] When vegetation grows unchecked for long periods, a fire that would normally burn surface fuels under the trees can climb ladder fuels into the canopy and become a crown fire.[7]

Fire also shapes the forest floor. The passage of a forest fire often leaves the duff layer, the partly decayed organic material on the forest floor, smouldering in an irregular pattern. This smouldering affects the viability of dormant seeds and forest regeneration, as well as posing a threat of reignition.[8] Outside forestry, controlled burning is one of the measures that have greatly reduced fires on railway rights-of-way, together with chemical control of vegetation and fire breaks.[9]

Prescribed fire complements work closer to homes. The handbook notes that mitigating strategic fuels around communities requires action largely on private property, where the Firewise programme promotes defensible space around homes.[10][11] Federal and state land management agencies apply prescribed fire and mechanical treatment over millions of acres.[3]

Fuel policy and research in the United States

Prescribed fire is part of US federal fuel policy as described in the 2008 handbook. The National Fire Plan, developed after the 2000 fire season, rests on five key points: firefighting, rehabilitation, hazardous fuels reduction, community assistance and accountability.[12] Hazardous fuels are defined there as dry brush and trees that have accumulated and increase the likelihood of unusually large fires.[12]

The Healthy Forests Restoration Act of 2003 speeds up hazardous fuel reduction and forest restoration projects on certain federal lands. Its provisions can be applied to as many as 8.1 million ha (20 million acres) of land managed by the Forest Service and the Bureau of Land Management.[12] At least 50 percent of the funding for projects under the act is to protect areas next to communities at risk of wildland fire.[12] Communities that prepare a Community Wildfire Protection Plan receive priority for funding of hazardous fuel reduction projects.[11]

Research supports these programmes. The Joint Fire Science Program, set up in 1998 as a partnership of six federal organisations, has four original purposes, all related to wildland fuels. They are fuels inventory and mapping, evaluation of fuels treatments, scheduling of fuels treatments and protocols for monitoring and evaluation.[5] Its research also covers air quality, smoke management and the social aspects of fire.[5] Digital mapping lets managers examine the relationships between watersheds, wildlife habitat and the impact of a prescribed fire.[5]

Public attitudes are also studied. As national fire policy changed, the handbook reports a renewed interest in how the public would react, including acceptance of "good fire" in wildland areas and of smoke in the air.[1] The handbook expects the preparation of fire managers and firefighters to use the beneficial aspects of prescribed fire to grow in importance.[10]

Fire behaviour and burning conditions

A prescribed fire obeys the same physics as a wildfire. Heat, oxygen and fuel must be present in the right proportion, and their balance decides whether a fire smoulders and spreads slowly or flames brightly and travels rapidly.[13][14] The ease of ignition and the rate of combustion of forest fuels depend mainly on the type of fuel, its continuity, its moisture content and its temperature.[13] The research topics listed in the handbook include the design of prescriptions for proper burning conditions, but the handbook does not give the parameter values.[1]

Fuel moisture changes with the weather. Dead fuel moisture follows that of the surrounding air with a delay called the time lag. It ranges from 1 hour for fuels under 6.35 mm (¼ in.), such as annual grass, to 1000 hours for logs and timber of 76.2–203 mm.[15] Green grass acts as a fire barrier, while fully cured grass in large, uniform cover is the most flammable ground fuel in the region.[16] Crown fires seldom occur when relative humidity is high, but conifer needles dry out quickly in hot, dry air.[17] The 2008 handbook reports about 1150 remote automated weather stations in the United States collecting wind, gusts, precipitation, temperature, relative humidity and fuel moisture every hour.[18]

Wind and slope raise the rate of spread. Wind forces oxygen into the fuel and bends the flames towards the unburned fuel ahead.[13] As a rule of thumb, the rate of spread doubles on a 30 percent slope and doubles again on a 55 percent slope.[19] Spot fires, started by burning embers or firebrands thrown ahead of the fire, become more frequent and severe as fuel moisture falls and wind increases.[15]

Two delayed effects matter for any fire left burning. A fire may creep through ground fuels under low brush at night, when the burning index is low. The next day, as the burning index rises, the dried vegetation can reburn hotly and carry the fire into the crowns.[17] Similarly, a fire confined to the ground can scorch and dry the tree crowns above it. If conditions change, a crown fire may then develop and sweep back over the area, burning more explosively because the crowns have been dried.[20]

Deliberate ignition and control lines

Deliberate ignition is also part of wildland fire suppression. Firefighters use drip torches to ignite backfires and burnouts, and burning out is one of the standard steps in suppressing a small wildfire.[18][21] Hotshot crews are trained in building firelines, burning out, setting backfires and mopping up.[22] Canadian research on suppression includes aerial ignition devices and backfiring methods.[1]

In suppression, a slowly advancing fire in sparse ground fuels may be stopped by a line dug down to mineral soil, which is soil with little humus or organic matter.[23] A glossary in NUREG-1805 (2004) defines controlling a fire as completing a control line around it, burning out the unburned area on the fire side of the line and cooling hot spots that threaten it.[24] Reignition of apparently dead fires is an important factor in forest fuels, so experienced firefighters feel the fuel by hand before leaving.[23] Mop-up puts out all embers and sparks so that none cross the line, and patrols check for fire crossing it.[22]

Escaped prescribed fires

The best-known escaped burn in the sources is the Cerro Grande fire of May 2000. It began as a prescribed burn under the control of the National Park Service in Bandelier National Monument near Los Alamos, New Mexico.[2][4] The burn was intended to cover about 360 ha (900 acres). The NFPA statistics chapter states that it spread over more than 48,000 acres, while the wildland chapter gives 47,650 acres (19,284 ha), roughly 53 times the planned area.[2][4]

The wildland chapter's narrative says the fire destroyed 235 homes; its historical-fire table calls them 235 structures and reports damage to the Los Alamos National Laboratory.[4][25] Its total estimated loss was $1 billion, making it the third-largest US fire loss of 1995–2004, or $1096 million in 2004 dollars.[2] Another handbook chapter on extreme events notes that the New Mexico fires of 2000 ultimately consumed part of the laboratory.[26]

The escape had consequences for policy. A moratorium on prescribed fire was put into effect after the blaze, and the fire marked the start of one of the most difficult fire seasons in half a century. The 2000 season is described as the worst in 80 years.[4] The National Fire Plan, with its emphasis on hazardous fuels reduction, was developed after that season.[12]

Burning is also dangerous for the crews involved. Of the 999 firefighters in the United States who died on duty between 1996 and 2005, 159 (15.9 percent) died as a result of wildland fires or control burns. These accounted for 25.5 percent of all fireground deaths over the period.[27] The source does not separate deaths during prescribed burns from those at wildfires. The wider data are covered under firefighter injuries and fatalities.

Smoke

Smoke is a mixture of solid particles, liquid droplets and gases. White smoke often consists of fine droplets such as condensed water vapour or pyrolysis products, while black smoke contains much soot.[28] Close to the fire, smoke is hot and optically dense; as it rises, entrained air cools and dilutes it.[28] Smoke management for prescribed fires is one of the US research topics listed in the handbook, alongside air quality.[1][5] The remote automated weather stations are also used to monitor environmental conditions and air quality.[18]

Crews working in vegetation smoke are exposed to its products. Air samples collected on wildland firefighters show a potential for hazardous exposure to respirable particulate, carbon monoxide, formaldehyde and acrolein.[29] At the time of the handbook, practice treated wildfire smoke as not immediately dangerous to life and health, although its health hazards had not been quantified. The handbook advised reducing exposure through short work periods, removing crews from heavy smoke, rest in smoke-free air or respiratory protection.[29]

Smoke from large vegetation fires can also affect infrastructure. The fire probabilistic risk assessment methodology for US nuclear power plants (NUREG/CR-6850, 2005) treats this explicitly. It assumes that exposure to substantial smoke, for example from a large forest fire, will cause very high-voltage transmission equipment to trip off-line.[30]

Recording in fire statistics

Prescribed burns are handled separately in US fire data. In the National Fire Incident Reporting System (NFIRS), version 5.0, the Wildland Fire Module documents vegetation fires as well as incidents of unauthorised, controlled or prescribed burning. These burning incidents are not counted as hostile fires.[31] NFIRS counts only fires that are hostile, defined as destructive and uncontrolled burning. Responses to burning with a permit, or to unauthorised burning, are not counted as fires at all unless they get out of control.[32]

This affects how wildland data can be read. Depending on state or local policy, the Wildland Fire Module may be used for brush, forest and grass fires, for fires on cultivated land, and for unauthorised, controlled or prescribed burning.[33] Wildland Fire Module reports may therefore exist for incidents that are not counted as fires.[33]

Terminology in fire safety engineering

The words "prescribed" and "controlled" have other meanings in fire protection that are unrelated to vegetation. In water spray protection, "controlled burning" is a strategy that limits fire spread when the burning material cannot be extinguished by water spray or when extinguishment is not desirable.[34] In fire service training, live burns in acquired buildings are governed in the United States by NFPA 1403, Standard on Live Fire Training Evolutions. Several firefighters died in such exercises, which the handbook links to failures to follow that standard.[35] These exercises are covered under live fire training.

In fire safety engineering, "prescribed fire" can also mean a design fire specified for an analysis. The handbook refers to the "prescribed fire scenario(s)" used to size separation distances, and notes that the Fire Dynamics Simulator calculates conditions "in relation to the prescribed fire" defined by the user.[36][37] In Australia, the handbook to the Fire Safety Verification Method (2020) speaks of "prescribed fire scenarios" that a hazard identification may show to be not applicable.[38] None of these uses involves the deliberate burning of vegetation.

See also

Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Smalley (2008), p. 13-77.
  2. ↑ 2.0 2.1 2.2 2.3 2.4 Hall and Cote (2008), p. 3-13.
  3. ↑ 3.0 3.1 3.2 Smalley (2008), p. 13-53.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 Smalley (2008), p. 13-54.
  5. ↑ 5.0 5.1 5.2 5.3 5.4 Smalley (2008), p. 13-76.
  6. ↑ Smalley (2008), p. 13-56.
  7. ↑ 7.0 7.1 Smalley (2008), p. 13-65.
  8. ↑ Ohlemiller (2002), p. 2-206.
  9. ↑ C. J. Wright (2008b), p. 21-114.
  10. ↑ 10.0 10.1 Smalley (2008), p. 13-78.
  11. ↑ 11.0 11.1 Smalley (2008), p. 13-67.
  12. ↑ 12.0 12.1 12.2 12.3 12.4 Smalley (2008), p. 13-69.
  13. ↑ 13.0 13.1 13.2 Smalley (2008), p. 13-57.
  14. ↑ Van Rossum (2027), §4.2.
  15. ↑ 15.0 15.1 Smalley (2008), p. 13-63.
  16. ↑ Smalley (2008), p. 13-61.
  17. ↑ 17.0 17.1 Smalley (2008), p. 13-62.
  18. ↑ 18.0 18.1 18.2 Smalley (2008), p. 13-73.
  19. ↑ Smalley (2008), p. 13-59.
  20. ↑ Smalley (2008), p. 13-64.
  21. ↑ Smalley (2008), p. 13-70.
  22. ↑ 22.0 22.1 Smalley (2008), p. 13-71.
  23. ↑ 23.0 23.1 Smalley (2008), p. 13-58.
  24. ↑ Iqbal and Salley (2004), p. F-17.
  25. ↑ Smalley (2008), p. 13-55.
  26. ↑ Meacham and Galioto (2008), p. 1-112.
  27. ↑ Smalley (2008), p. 13-74.
  28. ↑ 28.0 28.1 Van Rossum (2027), §6.1.
  29. ↑ 29.0 29.1 Teele (2008), p. 12-154.
  30. ↑ Nowlen et al. (2005b), p. T-14.
  31. ↑ Ahrens and Stewart (2008), p. 3-52.
  32. ↑ Ahrens and Stewart (2008), p. 3-48.
  33. ↑ 33.0 33.1 Ahrens et al. (2008), p. 3-65.
  34. ↑ Bell (2008), p. 16-182.
  35. ↑ Laughlin (2008), pp. 12-172–12-173.
  36. ↑ Janssens (2008), p. 2-72.
  37. ↑ Beyler et al. (2008), p. 3-100.
  38. ↑ Australian Building Codes Board (2020b), p. 60.

References

  • Ahrens, M., & Stewart, S. (2008). Fire data collection and databases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-43–3-59). National Fire Protection Association.
  • Ahrens, M., Frazier, P., & Kelch, G. (2008). Use of fire incident data and statistics. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-61–3-92). National Fire Protection Association.
  • Australian Building Codes Board. (2020b). Handbook: Fire Safety Verification Method (Print version 1.1).
  • Bell, K. M. (2008). Water spray protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 16-181–16-190). National Fire Protection Association.
  • Beyler, C. L., DiNenno, P. J., Carpenter, D. J., & Watts, J. M., Jr. (2008). Introduction to fire modeling. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-93–3-110). National Fire Protection Association.
  • Hall, J. R., Jr., & Cote, A. E. (2008). An overview of the fire problem and fire protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-3–3-30). National Fire Protection Association.
  • Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
  • Janssens, M. L. (2008). Basics of fire containment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-59–2-74). National Fire Protection Association.
  • Laughlin, J. W. (2008). Training programs for fire and emergency service personnel. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-161–12-175). National Fire Protection Association.
  • Meacham, B. J., & Galioto, C. (2008). Protecting against extreme events. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 1-109–1-136). National Fire Protection Association.
  • Nowlen, S. P., Najafi, B., Wyant, F. J., Forester, J., Kazarians, M., Kolaczkowski, A., Joglar, F., Funk, D., Hannaman, G., & Anoba, R. (2005b). EPRI/NRC-RES fire PRA methodology for nuclear power facilities: Vol. 2. Detailed methodology (NUREG/CR-6850; EPRI 1011989). Electric Power Research Institute; U.S. Nuclear Regulatory Commission, Office of Nuclear Regulatory Research.
  • Ohlemiller, T. J. (2002). Smoldering combustion. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-200–2-210). National Fire Protection Association; Society of Fire Protection Engineers.
  • Smalley, J. C. (2008). Wildland fire management. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-53–13-79). National Fire Protection Association.
  • Teele, B. W. (2008). Fire and emergency services protective clothing and protective equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-143–12-160). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
  • Wright, C. J. (2008b). Rail transportation systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-109–21-134). National Fire Protection Association.