Contents
Water supply curve is a relationship between available water pressure and delivered flow at a defined point in a supply system. [1] The curve describes a specified source and network condition. It can come from a measured flow test, a pump characteristic or a combination evaluated through the connecting pipework. A design comparison also needs the demand at the same reference point and a separate assessment of duration. [1][2]
The underlying hydraulic assessment follows water from a defined source to its intended outlet. Elevation, velocity changes and irreversible losses must be distinguished. Observations also need the flow and network conditions under which they were obtained. A mathematically correct result can still be misleading if a source condition, connecting segment or component loss has been omitted from the description. [3][1] Static pressure and flowing pressure describe different conditions. [4]
Reference point and curve interpretation
A hydrant flow test commonly supplies the initial observations for a fire water supply curve; the Hazen-Williams formula provides the empirical flow exponent used in a familiar approximation of supply pressure drop. The plotted curve remains conditional on the measured network state. Its smooth appearance does not imply exact knowledge of every possible discharge. [4][5]
Hydraulic calculation carries the selected design area demand back to the supply reference; this includes the pressure needed at the most demanding sprinklers and the losses along the route. A fire pump performance curve may contribute added head, but the addition varies with flow. Supply and pump characteristics therefore remain distinguishable within the combined comparison. [6]
A demand point below the available supply curve indicates a favourable pressure-flow comparison for those assumptions; it does not by itself establish sufficient storage, dependable replenishment or freedom from common failure. The time and availability dimensions require their own evidence. Treating the curve as the entire water-supply specification would omit those functions. [7][8]
Comparing supply and demand
Supply and demand curves answer complementary questions; a supply curve gives the pressure available at different flows under stated conditions. A demand calculation gives the pressure needed to deliver the selected flow through the protection system. Their comparison is meaningful only at a common reference point and for compatible operating assumptions. [1]
A common water-supply approximation treats the pressure drop from the test's static value as proportional to flow raised to the power 1.85. The relation can interpolate a measured pressure-flow pair and supports the traditional transformed-axis graph. It is an empirical representation of a network, not a physical guarantee at every extrapolated flow. [4][5]
| Symbol | Description | Unit |
|---|---|---|
| Static and test residual pressures | kPa | |
| Measured test discharge | L/min | |
| Investigated flow and predicted pressure | L/min; kPa |
Using the pressure and flow inputs in Fleming's printed example gives a useful arithmetic check; converted to SI, they are approximately 689 kPa static and 552 kPa residual at 3,785 L/min. At 1,703 L/min, the equation gives approximately 658 kPa. This recalculation uses the stated inputs; it does not reproduce the inconsistent intermediate answer printed in that example. [4]
A pump adds a further pressure-flow relationship; the available inlet pressure combines with the differential head developed by the pump, after appropriate elevation and velocity corrections. The resulting supply is not obtained by adding the rated pump pressure at every flow. Both high-flow delivery and low-flow maximum pressure need consideration. [2][9]
The calculation must also preserve the difference between capacity and duration; a source may meet a demand point initially while exhausting a finite reserve too soon. Two paths may appear redundant while sharing one vulnerable source or connecting segment. Pressure-flow agreement is therefore one part of demonstrating the performance of the complete supply arrangement. [7][8]
Measuring the available supply
A supply test relates an observed discharge to the pressure remaining elsewhere in the connected system; the initial static reading describes the condition before the test discharge begins. The residual reading describes the pressure while the measured discharge is flowing. Both belong to the same test arrangement and must be recorded with its location and operating conditions. [4][10]
The flowing outlet and the pressure observation have different functions; a pitot measurement in an appropriate free jet supports an estimate of outlet flow. A gauge at the residual hydrant measures pressure in the distribution system during that discharge. Substituting jet pressure for residual system pressure confuses two different physical quantities. [10][4]
The discharge estimate depends on outlet geometry and the coefficient representing its losses; a disturbed or nonuniform jet makes a single point reading less representative. Probe alignment and position also influence the measurement. For some discharge devices, a calibrated nozzle or suitable flowmeter provides a more appropriate method than applying a simple pitot relation. [10]
Test results describe a network state, rather than an unlimited promise of future supply; domestic demand, pumps, source levels and closed valves can change that state. The pressure reference must also be carried correctly to the building calculation. A test performed at a different elevation or upstream of additional resistance needs hydraulic interpretation before comparison with system demand. [11][1]
A main-drain test provides a different kind of evidence; the handbook uses changes from previous static and flowing readings to identify possible deterioration or obstruction. This is useful for detecting change, but it does not independently establish the full sprinkler demand. Test opening, supply state and instrument condition affect whether successive observations are comparable. [12]
Pump testing likewise separates a start test from a flow-performance test; running successfully without substantial discharge demonstrates some operating functions but does not establish the entire pump curve. Flowing observations across the relevant operating range give evidence about delivery capability. The handbook describes retaining records so that deterioration and the ability to meet system demand can be assessed. [13]
Applying the Hazen-Williams relation
The Hazen-Williams relation represents pipe friction through an empirical water-flow equation; Titus explains that its coefficient is fitted to flow behaviour rather than derived from a complete fluid-property model. Water temperature and the range of pipe conditions therefore matter to its interpretation. It is not a general-purpose equation for every liquid used in fire protection. [5]
The following form expresses the pressure loss through a straight length in kilopascals; it is obtained by converting Titus's bar-per-metre form and multiplying by pipe length. Flow is in litres per minute and actual internal diameter is in millimetres. Changing those units without changing the constant produces a different and incorrect calculation. [14]
| Symbol | Description | Unit |
|---|---|---|
| Frictional pressure loss and pipe length | kPa; m | |
| Water flow and actual internal diameter | L/min; mm | |
| Empirical Hazen-Williams coefficient | dimensionless |
Titus compares methods using a flow of approximately 1,893 L/min through 30.48 m of pipe with a 102.26 mm internal diameter. Using a C-factor of 100 gives approximately 69.4 kPa loss by this formula. The example demonstrates the method with stated inputs; it does not prescribe that coefficient for every steel pipe. Different condition assumptions produce different predictions for the same nominal pipe. [15]
Sensitivity can be illustrated without selecting another installation. Doubling flow at fixed diameter and C-factor multiplies the calculated loss by approximately 3.61. Reducing C from 120 to 80 multiplies loss by approximately 2.12 at unchanged flow. These recalculated ratios follow directly from the exponents and help explain why condition and demand assumptions matter. Titus cautions that Hazen-Williams becomes unsuitable for coefficients appreciably below 100, particularly for very rough pipes. The C-factor comparison therefore illustrates equation sensitivity rather than validating a severely deteriorated installation. [16][17]
The formula describes distributed resistance, not every possible obstruction; a partially closed valve or a lodged object can create a concentrated restriction that needs separate representation. Corrosion may affect both roughness and bore, while internal debris can move during testing or operation. Treating all these effects as an arbitrary change to C can hide the physical defect being investigated. [18][19]
Pressure, flow and energy
Water pressure describes only one part of the energy available in a pipe; elevation contributes potential energy, while movement contributes velocity head. Titus describes these quantities using head, expressed as an equivalent height of water. A hydraulic calculation must therefore compare locations through a common energy balance, rather than subtracting unrelated gauge readings. [20]
For steady, incompressible flow, the energy balance adds pump head and subtracts irreversible losses between two sections; the following form assumes that section-average velocity adequately represents kinetic energy. It describes a defined flow path, with all elevations measured from the same datum. Sudden changes require a different, transient analysis. [21]
| Symbol | Description | Unit |
|---|---|---|
| Pressure at the section | Pa | |
| Water density | kg/m³ | |
| Gravitational acceleration | m/s² | |
| Mean velocity | m/s | |
| Elevation, added pump head and head loss | m |
Pressure can decrease because water rises, because velocity increases, or because energy is dissipated; these effects have different physical meanings. An elevation change can be recovered on a descending route, whereas friction dissipates mechanical energy. A larger pipe can reduce friction but cannot remove the elevation difference between the source and the outlet. [22]
Continuity provides the corresponding flow constraint: volume flow equals cross-sectional area multiplied by mean velocity; the same flow moves faster through a smaller internal bore. At a junction, incoming and outgoing flows balance, while losses depend on the flow assigned to each connected segment. Nominal pipe size alone does not supply the internal diameter needed for this calculation. [21][23]
The pressure at a sprinkler is the pressure remaining after the complete upstream route has been considered; it is not the pressure indicated beside a remote pump or street hydrant. The route includes connecting mains, valves, elevation and distribution piping. Leaving out an inconvenient section creates an apparently favourable calculation without providing the corresponding water at the outlet. [24][25]
Flow, pressure and duration
A fire water supply has several necessary characteristics: adequate flow, sufficient pressure at that flow, an appropriate duration and availability when needed; these characteristics cannot replace one another. A large reservoir may have insufficient delivery capacity, while a high-pressure connection may offer too little sustained flow. The required combination depends on the fire protection demand being assessed. [11][26]
Demand must identify which outlets operate together; sprinkler calculations assemble the flows of individual operating sprinklers and include other applicable demands under the selected design basis. Municipal fire-flow planning addresses a different question and may include wider firefighting activity. Treating every quoted fire-flow value as a sprinkler demand obscures these differences. [27][28]
The supply location also matters; a pressure measured in a street main is not automatically available at a building riser. Connecting pipework, backflow assemblies and changes in elevation affect the transfer. The assessment follows the supply through these elements to the same reference point used for the calculated demand. [29][1]
Storage introduces a time dimension that a pressure-flow curve alone does not show; usable water is the quantity that the outlet or pump can actually draw while meeting its operating conditions. Water below the effective intake, or reserved for another purpose, cannot simply be counted as fire reserve. Replenishment contributes only through an identified source and a delivery arrangement that remains available. [30][7]
A constant-flow volume calculation multiplies flow by duration. In the following form, flow is in litres per minute and usable volume is in cubic metres. The factor converts litres to cubic metres. [7]
| Symbol | Description | Unit |
|---|---|---|
| Usable water volume | m³ | |
| Constant discharge and duration | L/min; min |
A worked example separates usable water from gross capacity. Using Fleming's example of 530 L/min for 30 minutes gives 15,900 L, or 15.9 m³, of usable water. This arithmetic does not select a design duration or establish the gross tank volume. The example is a historical worked calculation, with tank configuration and unavailable volume assessed separately. [7]
Public supplies can change with domestic use, industrial demand, maintenance and seasonal conditions; tank levels and pump operation can change during a fire as well. The design record therefore needs the conditions represented by the available supply, including relevant adverse conditions. A favourable isolated reading does not establish availability throughout the required incident duration. [11][31]
Availability and common dependencies
Two components do not necessarily provide two independent supplies; a pair of pumps may share the same tank, intake, electrical route or vulnerable connecting main. A looped network may still depend on one source connection. The relevant question is whether the required water path remains available after the particular failure being considered. [32][8]
The NIST investigation of the World Trade Center's 2001 fire suppression systems provides a specific illustration; its review identified vulnerabilities associated with floor-feed arrangements and with the limits of some hydraulic calculation paths. It also considered the dependence of manually operated equipment on personnel access and action. These findings describe that complex and that investigation; they are not failure probabilities for all buildings. [8]
The case also shows why upstream duplication alone is insufficient; alternative water sources may converge on a single downstream segment. Damage or isolation at that segment can interrupt the route to the affected area despite apparently generous upstream equipment. Conversely, a reserve serving another pressure zone does not automatically become a usable alternative without an available connection. [8]
Automatic and manual supply functions need separate treatment; a fire department connection depends on responding apparatus, water, personnel and access. A stored or pumped automatic supply can begin serving a demand without those same preliminary actions, provided its own operating chain remains intact. Calling both arrangements a water supply does not make their activation times or dependencies equivalent. [29][33]
Duration introduces further common dependencies; refill may rely on the same utility that a reserve is intended to supplement. Fuel and cooling water can constrain a driver even when the pump itself is mechanically sound. Seasonal source variation can affect both the initial reserve and its replenishment. Such dependencies belong in the description of the actual arrangement. [30][34][35]
Availability also changes during maintenance; sectional isolation can limit the area affected by work, while unclear valve identification can enlarge it. The handbook links planned shutdowns to preparation, notification and verified restoration. Records of the normal configuration make these operational controls meaningful rather than relying on an assumed open water path. [36]
See also
Notes
- ↑ 1.0 1.1 1.2 1.3 1.4 1.5 Fleming (2002), ch. 4-3, pp. 4-81–4-83.
- ↑ 2.0 2.1 Titus (2002), ch. 4-2, pp. 4-68–4-70.
- ↑ Titus (2002), ch. 4-2, pp. 4-47–4-56.
- ↑ 4.0 4.1 4.2 4.3 4.4 4.5 Fleming (2002), ch. 4-3, pp. 4-81.
- ↑ 5.0 5.1 5.2 Titus (2002), ch. 4-2, pp. 4-52–4-53.
- ↑ Fleming (2002), ch. 4-3, pp. 4-74–4-82.
- ↑ 7.0 7.1 7.2 7.3 7.4 Fleming (2002), ch. 4-3, pp. 4-83–4-84.
- ↑ 8.0 8.1 8.2 8.3 8.4 Hopkins et al. (2005), pp. xxxvii–xlii.
- ↑ Cote (2008), ch. 15.6, pp. 15-89–15-94.
- ↑ 10.0 10.1 10.2 Cote (2008), ch. 15.3, pp. 15-46–15-47.
- ↑ 11.0 11.1 11.2 Cote (2008), ch. 15.2, pp. 15-23–15-24.
- ↑ Cote (2008), ch. 16.11, pp. 16-210–16-211.
- ↑ Cote (2008), ch. 16.11, pp. 16-220.
- ↑ Titus (2002), ch. 4-2, pp. 4-52.
- ↑ Titus (2002), ch. 4-2, pp. 4-56.
- ↑ Titus (2002), ch. 4-2, pp. 4-52–4-54.
- ↑ Cote (2008), ch. 15.3, pp. 15-53.
- ↑ Cote (2008), ch. 15.5, pp. 15-79–15-81.
- ↑ Cote (2008), ch. 16.11, pp. 16-212.
- ↑ Titus (2002), ch. 4-2, pp. 4-45–4-48.
- ↑ 21.0 21.1 Titus (2002), ch. 4-2, pp. 4-47–4-50.
- ↑ Titus (2002), ch. 4-2, pp. 4-47–4-52.
- ↑ Cote (2008), ch. 16.3, pp. 16-41–16-42.
- ↑ Fleming (2002), ch. 4-3, pp. 4-75–4-81.
- ↑ Hopkins et al. (2005), pp. xxxvii–xxxviii.
- ↑ Cote (2008), ch. 15.4, pp. 15-63–15-67.
- ↑ Cote (2008), ch. 15.2, pp. 15-23–15-29.
- ↑ Fleming (2002), ch. 4-3, pp. 4-74–4-81.
- ↑ 29.0 29.1 Cote (2008), ch. 15.4, pp. 15-63–15-65.
- ↑ 30.0 30.1 Cote (2008), ch. 15.1, pp. 15-3–15-5.
- ↑ Cote (2008), ch. 15.4, pp. 15-63–15-64.
- ↑ Cote (2008), ch. 15.2, pp. 15-27–15-30.
- ↑ Cote (2008), ch. 16.10, pp. 16-200–16-201.
- ↑ Cote (2008), ch. 15.6, pp. 15-98–15-99.
- ↑ Cote (2008), ch. 13.4, pp. 13-40–13-44.
- ↑ Cote (2008), ch. 16.11, pp. 16-208–16-209,16-221.
References
- Cote, A. E. (Ed.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
- Fleming, R. P. (2002). Automatic sprinkler system calculations. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-72–4-87). National Fire Protection Association.
- Hopkins, M., Schoenrock, J., & Budnick, E. (2005). Fire suppression systems (NIST NCSTAR 1-4B). National Institute of Standards and Technology.
- Titus, J. J. (2002). Hydraulics. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-44–4-71). National Fire Protection Association.