Skip to content
From Fire Safety Academy Wiki
Revision as of 22:29, 7 November 2026 by Mark (talk | contribs) (New FSE wiki article: Recreational vehicle fire (written by Claude Opus 5.5))
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Contents
  1. 1Definition and types
  2. 2Growth and use
  3. 3Fire hazards
  4. 4Standards and fire safety measures
  5. 5Smoke alarms and carbon monoxide
  6. 6Fire statistics and data limits
  7. 7Response
  8. 8See also
  9. 9Notes
  10. 10References

A recreational vehicle fire is a fire in a recreational vehicle (RV), such as a motor home, caravan (travel trailer), folding camping trailer or truck camper. An RV is a vehicle that combines transportation with temporary living quarters for travel, recreation and camping.[1] It therefore carries the hazards of a road vehicle, described in Motor vehicle fire, together with those of a small dwelling.

Many RVs contain propane appliances for cooking and heating, a 120 V AC electrical system, sleeping places and combustible interior finishes.[2] In the United States, the fire and life safety requirements for RVs are set out in NFPA 1192, Standard on Recreational Vehicles.[3] The standard requires portable fire extinguishers and, since the 1990s, propane detectors and, in RVs with an internal combustion engine, carbon monoxide detectors.[2] Smoke alarms have been addressed since the first fire safety provisions of 1982.[4] Nearly 8 million US households owned an RV around 2005, but reliable fire statistics for RVs are scarce, because RV fires are often recorded as fires in mobile homes or under brand names.[2]

Definition and types

The definition used in NFPA 1192, as refined by the Recreation Vehicle Industry Association (RVIA), covers three forms.[1] Motor homes have their own motor power, truck campers are mounted on a truck, and travel trailers, fifth-wheel trailers and folding camping trailers are towed by another vehicle. Conversion vehicles, off-road vehicles, emergency living units and manufactured housing for long-term residence, such as park trailers and mobile homes, are not RVs under this definition.

Motor homes are divided into three types. A Type A motor home is generally the largest, and its driving compartment is built by the RV manufacturer.[1] A Type B motor home, or van camper, is the smallest and is built inside a van whose shell comes from the chassis manufacturer. A Type C motor home has a cab supplied by the chassis manufacturer and falls in between in size. Type A motor homes sleep 2 to 6 people, Type B 2 to 4 and Type C 6 to 10.[5]

A towable RV is designed to be towed by a car, van or pickup truck without a special highway permit, and it needs no permanent connection on site.[6] A conventional travel trailer is 3.66 to 10.67 m (12–35 ft) long and sleeps 4 to 8 people.[5] Sport utility RVs contain a built-in garage for motorcycles, all-terrain vehicles or other sports equipment.

The RV differs from a Manufactured home, although the two share a history and were long covered by the same NFPA standards. US manufactured homes are built to the federal HUD Code and placed on piers, footings or a permanent foundation.[7] Their sections are typically 2.5 m (8 ft) or more wide and 12.2 to 24.4 m (40–80 ft) long. In US fire statistics, a fire in a motor home, camper or RV used as a fixed structure is coded as a structure fire.[8] A fire in an RV on the road falls among the vehicle fires.

Growth and use

RVs have existed since the beginning of motor travel in the early 1900s.[1] In the late 1940s and early 1950s, portable propane or butane cylinders allowed gas stoves and heaters to replace liquid-fuelled models.[9] Refrigerators, running hot water, toilets, showers and 110 V generators followed. With these comforts came concerns about the safe installation of plumbing, gas and electrical systems, and California introduced RV safety standards in the late 1950s.

The vehicles also grew larger. From the 1930s to the early 1960s, most units were shorter than 6.1 m (20 ft); today 9.14 to 12.19 m (30–40 ft) is common.[4] From the early 1980s, larger rigs offered living rooms, air-conditioning and other comforts of a home. Some retirees and families sold their houses and lived on the road full time, so an RV may be a permanent dwelling for some of its users. By about 2005, nearly 8 million US households, or one in twelve vehicle-owning households, owned at least one RV.[4] About 8.2 million RVs were on US roads, and annual shipments rose from 259,200 in 1994 to 390,500 in 2006, an increase of about half.[10]

Fire hazards

The main fire hazards of an RV come from its fuels, its electrical system and its interior. Motor homes carry petrol or diesel for the engine, and NFPA 1192 contains separate provisions for these fuel systems and for propane engines.[3] Many RVs also carry liquefied petroleum gas (propane) for appliances, and gas-fired heaters are popular in RVs.[11] Liquefied petroleum gas vapour is about 1.5 times as heavy as air, so it spreads along the floor or ground, and the ignitable mixture extends beyond the visible fog of a leak.[12] The gas is odorised so that it can be smelled at less than one fifth of its lower flammable limit. Odorants can fade, however, and the sense of smell weakens with age.[13]

In vehicles that use it as engine fuel, propane is stored as a liquid at about 827 to 1,379 kPa (120–200 psig).[14] A gas container exposed to flames can weaken and rupture. The handbook advises cooling such a container to avoid a BLEVE, a boiling liquid expanding vapour explosion, and leaving the area at once if no hose streams are available.[15] At any road accident involving a travel trailer or motor home, the presence of propane is assumed, smoking is prohibited and open flames and lights are kept well away.[16]

The electrical system adds a second group of hazards. An RV combines a low-voltage vehicle system with a 120 V AC system, supplied through a power supply assembly or by a generator.[2] NFPA 1192 therefore sets minimum insulation ratings for low-voltage wiring and limits the number of branch circuits on a 30 A supply. Heating appliances that burn liquid fuel or gas have their own UL standards, UL 307(a) and UL 307(b), for mobile homes and RVs.[17] RVs also offer little shelter in thunderstorms. Enclosed vehicles with metal tops and bodies protect their occupants against lightning, but RVs that are open or not made of metal offer little or no protection.[18]

The interior combines kitchen, sleeping and bathroom facilities within one vehicle.[1] NFPA 1192 has regulated interior finishes and textile and film materials since 1982.[4] It uses the ASTM E162 radiant panel test for cabinet door and drawer faces, exposed cabinet bottoms and end panels, and tub and shower walls. A radiant panel index of 200 is required for these surfaces.[19] Sport utility RVs carry motorcycles or all-terrain vehicles with internal combustion engines inside, so NFPA 1192 requires a ventilated transport area with a vapour-tight separation from the living area.[2]

Standards and fire safety measures

NFPA work on trailers began with a Committee on Trailers and Trailer Camps in 1937.[10] Its first standard of 1939 was followed in 1940 by a standard for trailer coaches and trailer coach camps. The first Standard for Recreational Vehicles, NFPA 501C, appeared in 1970 and defined motor homes, travel trailers, camping trailers and truck campers.[4] Fire safety requirements were first added in 1982, covering interior finish, textile and film flammability, exits, fire detection equipment and smoke alarms. From 1987 to 2005 the standard was updated every three years.[4] It was renumbered NFPA 1192 in 1999, and in 2005 the requirements of the separate ANSI A119.2 standard were merged into it.[3]

Several changes from the 1993 edition onwards may explain fewer RV fire deaths, according to the handbook author.[2] The minimum portable extinguisher for towable RVs was raised from 4B:C to 5B:C, and motorised RVs were required to carry a 10B:C extinguisher. Carbon monoxide detectors became mandatory in all RVs with an internal combustion engine, and propane detectors in all RVs with propane appliances and a 120 V AC system. Emergency exits were enlarged and marked, and propane containers had to be shielded from exhaust parts and other hot surfaces.

The electrical changes were equally specific. Low-voltage wiring must have an insulation rating of at least 90 °C for interior use and 125 °C in an engine area.[2] A 30 A power supply may serve at most five branch circuits, and an RV may have only one power supply assembly. Low-voltage light fittings must be listed to limit heat build-up at their mounting surfaces, and countertop sockets near sinks need ground-fault circuit interrupters.

Compliance relies largely on the industry itself. The RVIA represents more than 550 manufacturers and suppliers that produce about 98% of all RVs built in the United States.[2] Its seal certifies compliance with more than 500 electrical, plumbing, heating and fire and life safety requirements of NFPA 1192, and members are subject to unannounced plant inspections. The state and federal programmes are self-certification schemes without oversight by an outside agency, but manufacturers must report safety defects and usually recall the affected vehicles. RV parks and campgrounds are covered by NFPA 1194, which includes fire detection and alarm services, posted emergency information and provisions for wildland/urban interface areas.[3]

Smoke alarms and carbon monoxide

Smoke alarms are the basic fire warning device in homes, and NFPA 1192 has addressed them in RVs since 1982.[20][4] Residential detection ranges from one single-station smoke alarm in an apartment, manufactured home or RV to large wired systems.[21] In US homes, having smoke detectors present cuts the chance of dying in a fire nearly in half.[20] About one third of home smoke alarms, however, do not work when a fire occurs, usually because of dead or missing batteries.[21]

Carbon monoxide (CO) is a colourless and odourless gas produced by incomplete combustion.[22] When inhaled, it replaces oxygen in the haemoglobin of the blood and forms carboxyhaemoglobin (COHb). Sources include improperly operating heating appliances, blocked or missing vents, idling vehicles in attached garages and portable equipment such as generators. In fires, CO is the most important asphyxiant: in one pathology study, 69% of fire victims had COHb levels that can cause incapacitation, at or above 30%.[23] Loss of consciousness is predicted at about 40% COHb, but can occur from 30%, and death at 50 to 70%. The first symptom, a headache, appears at about 15–20%.[24]

The effect of CO depends on the dose, the product of concentration and time.[25] Far from a fire, CO concentrations can be very high even where visibility exceeds 20 m. US guidance gives approximate effects for healthy adults. At 200 ppm, a mild headache follows after 2–3 hours; 400 ppm causes headache and nausea after 1–2 hours, and 1,000 ppm loss of consciousness after 1 hour.[26] Children, the elderly and people with heart or lung disease can be affected at lower levels.

The COHb level after a given exposure can be estimated with an uptake equation from the annex of NFPA 720. It combines the initial COHb level, which decays over time, with a growing term that depends on the CO concentration in the air.[26] The time constant depends on a factor B for work effort.

%COHbt=%COHb0e−t/(2398B)+218[1−e−t/(2398B)][0.0003+CCO1316]

Symbol Description Unit
%COHbt Carboxyhaemoglobin in the blood at time t %
%COHb0 Carboxyhaemoglobin at the start of the exposure %
t Exposure time min
B Factor for work effort, 0.0404 –
CCO Carbon monoxide concentration in the air ppm

As a worked example, assume that exhaust from an engine or generator raises the CO level in a closed RV to 400 ppm. The starting COHb of a non-smoker can be taken as 0.8%.[27] With B = 0.0404, the time constant 2398B is 96.9 minutes. After 30 minutes the equation gives 18% COHb, enough for a headache, and after 60 minutes 31%, enough to cause incapacitation.[26][23] The 30% level is reached after about 57 minutes, so on this conservative estimate less than one hour passes before incapacitation becomes possible. A second method, the fractional dose equation for light activity, gives incapacitation at 400 ppm after about 73 minutes.[28]

Both results are approximate. The equation assumes a working adult, while the US table of effects for healthy adults at 400 ppm lists only headache and nausea after 1–2 hours.[26] At concentrations above about 600 ppm and long exposures, the equation even predicts COHb levels above 100%, which is physically impossible. In dwellings, NFPA 720 places CO alarms outside each separate sleeping area, on the wall or ceiling, because CO mixes readily with air.[29] A carbon monoxide alarm sounds a distinct temporal 4 pattern, and the first response is to open windows and check the occupants.[30]

Fire statistics and data limits

The handbook reports that deaths from fire in RVs fell between 1993 and 2002, but gives no numbers.[2] The reasons are difficult to determine, because records are limited and police accident reports classify RVs inconsistently. RVs are sometimes reported as mobile homes or manufactured homes, and motor homes and trailers are often listed under brand names such as Airstream or Winnebago. All-terrain vehicles and dune buggies are also sometimes recorded as RVs, which further distorts the data.

National vehicle fire analyses do not always treat RVs the same way. One handbook analysis of passenger vehicle fires excluded off-road recreational vehicles and trailers, while an NFPA report on the same subject included them.[31] Because an RV used as a fixed structure is coded as a structure fire, its fires can also appear in the building statistics.[8] The source documents contain no heat release rate measurements or full-scale fire tests of motor homes or caravans.

Response

The handbook steps for any vehicle fire also apply to RVs. The engine and electrical systems are shut off, everyone is moved well away, preferably uphill and upwind, and the fire department is called.[16] A fire is fought only if this can be done without danger. Many people keep extinguishers in vans and motor homes, and NFPA 1192 requires them in RVs.[2]

For fire fighters, the propane system shapes the response. Apparatus is placed upwind, because propane vapour stays heavier than air and can travel a long way downwind.[32] For propane-fuelled vehicles, the handbook adds that water streams can control the fire and disperse the vapour, and that the main shutoff valve of the container is closed where possible. A burning gas leak is left to burn until the flow is stopped, because putting out the flame could let unburned gas accumulate and explode later.[15] Fire-exposed containers are kept cool with water, while water on a pool of liquid gas is avoided because it increases the rate of evaporation.[12]

See also

Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 Hopkins (2008), p. 21-91.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 Hopkins (2008), p. 21-99.
  3. ↑ 3.0 3.1 3.2 3.3 Hopkins (2008), p. 21-98.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 4.6 Hopkins (2008), p. 21-96.
  5. ↑ 5.0 5.1 Hopkins (2008), p. 21-93.
  6. ↑ Hopkins (2008), p. 21-92.
  7. ↑ Paoletti (2008), pp. 20-63–20-64.
  8. ↑ 8.0 8.1 Ahrens et al. (2008), p. 3-67.
  9. ↑ Hopkins (2008), pp. 21-95–21-96.
  10. ↑ 10.0 10.1 Hopkins (2008), p. 21-97.
  11. ↑ Gore Willse (2008a), p. 10-16.
  12. ↑ 12.0 12.1 Lemoff (2008), p. 6-184.
  13. ↑ Rivkin (2008b), p. 21-60.
  14. ↑ Rivkin (2008b), p. 21-72.
  15. ↑ 15.0 15.1 Routhier (2008), p. 21-23.
  16. ↑ 16.0 16.1 Routhier (2008), p. 21-22.
  17. ↑ Routhier (2008), p. 21-19.
  18. ↑ Caloggero (2008), p. 11-80.
  19. ↑ Hirschler (2008b), p. 18-32.
  20. ↑ 20.0 20.1 Gottuk (2008), p. 14-79.
  21. ↑ 21.0 21.1 Gottuk (2008), p. 14-81.
  22. ↑ Black (2008), p. 14-113.
  23. ↑ 23.0 23.1 Purser (2002), p. 2-100.
  24. ↑ Purser (2002), p. 2-101.
  25. ↑ Van Rossum (2027), §6.1.
  26. ↑ 26.0 26.1 26.2 26.3 Black (2008), p. 14-114.
  27. ↑ Purser (2002), p. 2-164.
  28. ↑ Purser (2002), p. 2-103.
  29. ↑ Black (2008), p. 14-115.
  30. ↑ Black (2008), p. 14-116.
  31. ↑ Long et al. (2008), p. 21-5.
  32. ↑ Rivkin (2008b), p. 21-74.

References

  • Ahrens, M., Frazier, P., & Kelch, G. (2008). Use of fire incident data and statistics. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-61–3-92). National Fire Protection Association.
  • Black, A. (2008). Carbon monoxide detection in residential occupancies. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-113–14-117). National Fire Protection Association.
  • Caloggero, J. M. (2008). Lightning protection systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 11-69–11-81). National Fire Protection Association.
  • Gore Willse, P. J. (2008a). Heating systems and appliances. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 10-9–10-56). National Fire Protection Association.
  • Gottuk, D. T. (2008). Household fire-warning equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-79–14-87). National Fire Protection Association.
  • Hirschler, M. M. (2008b). Interior finish. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 18-23–18-42). National Fire Protection Association.
  • Hopkins, B. A. (2008). Recreational vehicles. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-91–21-100). National Fire Protection Association.
  • Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
  • Long, R. T., Jr., Colwell, J. D., Ray, R., Grossman, H. L., Thomas, B., & Strassburger, R. (2008). Passenger vehicle fires. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-3–21-14). National Fire Protection Association.
  • Paoletti, K. M. (2008). Manufactured housing. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 20-63–20-71). National Fire Protection Association.
  • Purser, D. A. (2002). Toxicity assessment of combustion products. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-83–2-171). National Fire Protection Association; Society of Fire Protection Engineers.
  • Rivkin, C. H. (2008b). Vehicle fueling using gaseous fuels. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-41–21-76). National Fire Protection Association.
  • Routhier, B. (2008). Fire safety in commercial vehicles. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-15–21-27). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.