Skip to content
From Fire Safety Academy Wiki
Revision as of 21:58, 7 November 2026 by Peter (talk | contribs) (New FSE wiki article: Burning velocity (written by Claude Opus 5.5))
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Contents
  1. 1Definition and related quantities
  2. 2Flame structure and physical basis
  3. 3Typical values
  4. 4Effects of temperature, pressure and turbulence
  5. 5Use in closed-vessel explosion calculations
  6. 6Use in explosion protection design
    1. 6.1Worked example
  7. 7Flame acceleration and detonation
  8. 8Limitations and uncertainty
  9. 9See also
  10. 10Notes
  11. 11References

Burning velocity is the speed at which a flame moves into the unburned gas directly ahead of it, measured relative to that gas.[1] It is a property of a premixed flame, in which fuel and air are mixed before ignition.[2] The fundamental burning velocity (Su), also called the laminar burning velocity, is the value for a smooth laminar flame under stated conditions of composition, temperature and pressure.[1][3] Most hydrocarbons burning in air have values of about 40 to 47 cm/s, while hydrogen reaches about 3.1 m/s.[4][5] Burning velocity differs from flame speed, which is measured from a fixed point and also includes the motion of the expanding gas.[1]

In a deflagration, the burning velocity and the area of the flame together set the rate at which the pressure rises in an enclosure.[6][7] For that reason the 2007 edition of NFPA 68, the American standard on deflagration venting, used it to size vents for low-strength enclosures.[8] Tabulated values describe quiet laminar flames, and turbulence in real equipment can multiply the effective burning velocity several times.[9] Laboratories also report somewhat different values for the same gas.[9]

Definition and related quantities

The Fire Protection Handbook defines burning velocity as the rate of flame propagation relative to the unburned gas ahead of the flame. The fundamental burning velocity is that of a laminar flame under stated conditions of composition, temperature and pressure of the unburned gas.[1] The SFPE Handbook describes the same quantity as the velocity with which a premixed flame moves normal to its surface through the adjacent unburnt mixture.[10] The glossary of NUREG-1805 adds that it is measured at constant pressure and depends on mixture composition, temperature and pressure.[3] All three definitions describe the speed of the flame front with respect to the gas it consumes.

A flat flame on a burner shows what this means. Such a flame is stable only when the flow velocity of the incoming mixture equals its burning velocity.[10] If the flow is too fast the flame is blown off, and if it is too slow the flame flashes back.[10] The conical flame of a Bunsen burner is stable over a much wider range of flows, because its inner cone changes its area until the two velocities balance again.[10]

Flame speed is the speed of the flame front relative to a fixed reference point.[1] When a flame burns outwards from an ignition point, the hot products expand and push the unburned gas ahead of the front. The minimum flame speed therefore equals the fundamental burning velocity multiplied by the expansion factor, the ratio of unburned to burned gas density:[1]

Sf,min=ESu,E=ρuρb

For many hydrocarbons near the stoichiometric concentration, this flame speed is 350 to 440 cm/s.[4] Beyler gives a maximum laminar burning velocity of 0.45 m/s and an expansion ratio of 7.4 for methane, and 0.52 m/s and 7.6 for propane.[11] The products, 3.3 and 4.0 m/s, are close to the laminar flame speeds of 3.5 and 4.0 m/s that he reports.[11] Flame speed also rises with turbulence caused by obstructions, the volume of the enclosure, the ignition energy and the mixture temperature. It therefore cannot be determined from the properties of the mixture alone.[1]

A flame travelling along a duct away from an open end moves at first at a fairly uniform linear speed V, set by the burning velocity and the area of the flame front:[12]

V=SuAfAd

The curved flame front is typically two to three times larger than the duct cross-section.[12] A propane flame with a burning velocity of 0.46 m/s therefore moves along a duct at about 0.9 to 1.4 m/s before it accelerates.[5] Simmons notes that this distinction matters when automatic protection is designed.[12]

Flame structure and physical basis

Introduction to Fire Safety Engineering divides flames into premixed flames and diffusion flames. In a premixed flame, air and fuel are already mixed before ignition, as in a gas burner or a Bunsen burner.[13] Drysdale illustrates the difference with power densities of 100 to 200 MW/m³ for premixed flames and 0.5 to 1 MW/m³ for diffusion flames.[2] In real fires premixed combustion is relatively unimportant, because the flames above burning materials are diffusion flames.[14] NUREG-1805 places turbulent premixed flames in boilers, furnaces, gas burners, oxyacetylene torches, petrol engines and cooking ranges.[15] Burning velocity is therefore mainly a quantity for gas and vapour explosions, burners and the ignition of flammable mixtures.

The flame advances because it heats and activates the fresh mixture in front of it. In the preheating zone the temperature rises by heat conducted back from the hotter parts of the flame, and chemical reaction starts only at about 700 K.[16] Free radicals that diffuse back from the hot zone then start the primary reaction.[16] The conservation equations for mass, energy and species can be solved numerically for the burning velocity, given a detailed reaction mechanism.[16]

Because heat release drives the process, hotter flames have higher burning velocities.[9] A premixed flame cannot propagate unless it can produce a flame temperature above about 1300 °C (about 1600 K).[2] Inert gases such as nitrogen, argon and carbon dioxide lower the flame temperature, and if they lower the burning velocity far enough, the flame is extinguished.[17] Yu and Newman describe one mechanism: once dilution reduces the burning velocity below the buoyant motions around the flame, the burning surface is strained and disrupted.[18] The flammability limits mark the range of compositions within which a self-sustaining flame can propagate at all.[9]

Premixed burning also occurs in building fires. Introduction to Fire Safety Engineering describes a smoke gas explosion as the very rapid burning of pyrolysis gases that are reasonably premixed with air, at a concentration between the lower and upper explosion limits.[19] Benedetti notes that flames travel through premixed mixtures at more than a metre per second, and that the process is then virtually impossible to interrupt.[20]

Typical values

The handbook chapter on deflagration venting lists fundamental burning velocities in air for a long list of gases and vapours. The table gives a selection, from the slowest to the fastest.[5] Most common fuels fall in a narrow band, and all saturated hydrocarbons have about the same maximum burning velocity.[9]

Fundamental burning velocity of selected gases and vapours in air[5]
Gas or vapour Su (cm/s) Gas or vapour Su (cm/s)
Methane 40 Benzene 48
Gasoline (100-octane) 40 Acetone 54
Toluene 41 Methyl alcohol 56
Isopropyl alcohol 41 Carbon disulfide 58
n-Butane 45 1,3-Butadiene 64
Propane 46 Ethylene 80
n-Hexane 46 Propylene oxide 82
Carbon monoxide 46 Ethylene oxide 108
Ethane 47 Acetylene 166
Diethyl ether 47 Hydrogen 312

The alcohols, ketones and aromatic compounds in the table lie between 41 and 56 cm/s. A few reactive gases stand out: ethylene oxide reaches 108 cm/s, acetylene 166 cm/s and hydrogen 312 cm/s.[5] The handbook and NUREG-1805 both describe hydrogen as having the highest burning velocity of any gas.[21][22] Its value is almost seven times that of propane.

The oxidant matters as much as the fuel. At room temperature and atmospheric pressure, the SFPE Handbook gives maximum laminar burning velocities of 41 cm/s for propane–air and 360 cm/s for propane–oxygen.[9] The corresponding values are 175 and 1120 cm/s for acetylene, and 320 and 1180 cm/s for hydrogen.[9] The difference follows from the flame temperature, because nitrogen in air acts as a thermal sink. Drysdale gives about 2000 °C for a stoichiometric propane–air flame and about 4500 °C for propane with oxygen.[23]

Tabulated laminar values are usually measured at the worst-case concentration of each gas.[7] The maximum burning velocity lies on the fuel-rich side of the stoichiometric mixture, a shift that Beyler attributes to preferential diffusion of the reactants.[24] Near the flammability limits flames propagate slowly, which leaves time for heat losses to the walls of a vessel.[7]

Effects of temperature, pressure and turbulence

Preheating raises the burning velocity: when propane–air mixtures are heated from 300 to 480 K, the maximum burning velocity doubles.[9] The effect of pressure is often written as a power law, in which the ratio of burning velocities equals the ratio of pressures raised to an exponent n:[9]

Su,aSu,b=(papb)n

Reported values of n range from 0.25 for hot flames with oxygen to −0.33 for cooler flames supported by air.[9] With n = −0.33, doubling the pressure lowers the burning velocity of an air flame by about 20 %.

Turbulence has the largest effect. In a tube the flow is always laminar at a Reynolds number below 2300 and usually turbulent above 3200.[9] As the Reynolds number rises, local velocity fluctuations blur the flame front into a "brush" with a larger effective area.[9] For propane, ethene and acetylene flames in air, the burning velocity roughly doubles as the Reynolds number rises to 40,000. Theory suggests up to a fivefold increase at very high turbulence.[9]

Explosion calculations express this with a turbulence factor χ, the ratio of turbulent to laminar burning velocity.[7] Ural and Garzia note that pre-existing turbulence, flame-induced turbulence and enclosure geometry increase both the burning velocity and the flame area.[25] In an enclosure with large openings, the maximum explosion pressure also depends on the burning velocity and the maximum flame area.[25]

Use in closed-vessel explosion calculations

The closed-vessel theory in the SFPE Handbook assumes that the flame speed is small compared with the speed of sound, so the pressure is uniform at any moment.[7] It also assumes that the fractional pressure rise equals the fraction of mass burned, and that the unburned gas is compressed isentropically.[4] The mass burning rate is then the product of unburned gas density, turbulence factor, burning velocity and flame area:[7]

dmbdt=ρuχSuAf

For a spherical flame growing from the centre of a vessel, the early pressure rise grows with the cube of time, as long as it is small compared with the initial pressure:[4]

P−P0P0=(1γ+P0Pm−P0)2(Pm−P0P0)3(χSuta)3≪1

The Fire Protection Handbook states the same scaling: early in a deflagration the pressure rise varies as (Sut/a)³, where a is the radius of a sphere with the enclosure volume.[26] In the SFPE example, the approximation matches the full numerical solution below 2 psig (13.8 kPa) and differs by about 20 % up to 8 psig (55 kPa).[4] The flame has then reached half the vessel radius at 2 psig and 80 % at 16 psig, while the final pressure is 93 psig. Most of the pressure is therefore generated late, when the flame is close to the walls.[4][27]

The same model links burning velocity to the deflagration index KG, the maximum rate of pressure rise multiplied by the cube root of the vessel volume.[27] In theory the maximum rate occurs at the end of the explosion, which gives:[27]

KG=4.84χSu(PmP0)1/γ(Pm−P0)

Measured values of KG generally increase with Su, but not in direct proportion, because χ varies among gases in a way that cannot be predicted beforehand.[27] Zalosh derives χ = 1.10 for n-butane from its measured KG of 92 bar·m/s.[28] The same calculation with his data for other gases, taking 1 bar initial pressure and γ = 1.4, gives χ of about 0.90 for methane, 1.19 for propane and 1.23 for hydrogen.[7] Acetylene gives 2.89, so it develops a much faster pressure rise than its laminar burning velocity alone would predict.[7]

Symbol Description Unit
Su fundamental (laminar) burning velocity m/s or cm/s
Sf,min minimum flame speed relative to a fixed point m/s
E expansion factor, ratio of unburned to burned gas density –
ρu, ρb density of the unburned and of the burned gas kg/m³
V linear flame velocity along a duct m/s
Af, Ad area of the flame front; cross-sectional area of the duct m²
pa, pb, n two pressures being compared; pressure exponent Pa; –
mb mass of burned gas in the enclosure kg
χ turbulence factor, ratio of turbulent to laminar burning velocity –
P, P0, Pm pressure at time t, initial pressure, closed-vessel deflagration pressure Pa or bar
γ ratio of specific heats of the unburned gas –
t time after ignition s
a radius of the vessel, or of a sphere with the same volume m
KG deflagration index of a gas bar·m/s
Av, AS vent area; internal surface area of the enclosure m²
C venting parameter bar1/2
Pred maximum pressure in the vented enclosure (gauge) bar

The value γ = 1.4 applies to most flammable hydrocarbon–air mixtures.[4] Continuing the calculation up to the final pressure requires a correlation for the change of Su as the unburned gas is compressed and heated.[27]

Use in explosion protection design

The rate of pressure rise is the most important parameter in the design of explosion venting. A rapid rise leaves only a short time for venting and, all other factors being equal, requires a larger vent.[29] In the United States, the 2007 edition of NFPA 68, as described by Schwab (2008b), sizes vents for low-strength enclosures from the burning velocity. Such an enclosure can withstand a reduced pressure of not more than 1.5 psi (0.1 bar gauge).[8] The vent area is proportional to the internal surface area and inversely proportional to the square root of the reduced pressure:[8]

Av=CASPred1/2

The venting parameter C, in bar1/2, follows from the fundamental burning velocity in cm/s, for burning velocities below 60 cm/s:[8]

C=1.57×10−5Su2+1.57×10−4Su+0.0109

According to Schwab, burning-velocity data now allowed venting parameters for more individual fuels than earlier editions. The designer should consider the material with the highest fundamental burning velocity that could be present.[30] The 1998 edition, as described in the SFPE Handbook, still used fixed constants: 0.037 bar1/2 for methane and 0.045 bar1/2 for gases with burning velocities below 60 cm/s.[31] For high-strength enclosures the handbook gives a vent equation based on KG instead, valid up to 550 bar·m/s.[30] Ural and Garzia note that no standard test method for KG and burning velocity was yet available, and that Annex C of NFPA 68 (2007 edition) gave guidance.[32]

Burning velocity also sets the time available for active protection. In a handbook example, a 1 m radius enclosure with a burning velocity of 45 cm/s, typical of near-stoichiometric propane–air, reaches 2 psig (0.14 bar) in about 0.2 s.[26] If the enclosure fails at that pressure, venting or suppression must act within 0.2 s of ignition.[26] Flames in ducts accelerate as they travel. By 2008 no universally accepted method existed to predict flame speed in industrial pipes, so suppliers of explosion isolation systems used proprietary correlations.[33]

Worked example

The first part checks the handbook time. A compact enclosure has the volume of a sphere with a radius of 1 m, about 4.19 m³, and contains propane–air with Su = 0.45 m/s.[26] The flame is laminar (χ = 1), γ = 1.4, the initial pressure is 101.3 kPa, and the closed-vessel pressure is 640 kPa gauge, as in the SFPE example.[4] A damage threshold of 2 psig, or 13.8 kPa, means (P − P0)/P0 = 0.136. The first two factors of the early-stage equation equal (0.714 + 0.158)² × 6.32³ ≈ 192, so that:[4]

t=aχSu(0.136192)1/3=1.00.45×0.0892≈0.198 s

This agrees with the "about 0.2 s" in the handbook.[26] As an available time it is rounded down, to 0.19 s. For hydrogen–air at 3.0 m/s the time falls to about 0.029 s. Any turbulence (χ > 1) shortens both times in proportion.

The second part sizes a vent for the room of 4 m × 4 m × 3 m used in the SFPE examples. It has 80 m² of internal surface and a damage threshold of 1.0 psi (0.0689 bar).[31] For propane at 46 cm/s, the venting parameter of NFPA 68 (2007 edition) is:[5][8]

C=1.57×10−5×462+1.57×10−4×46+0.0109=0.0513 bar1/2

The vent area is 0.0513 × 80 / 0.06891/2 = 15.64 m², rounded up to 15.7 m² because it is a required value. Methane at 40 cm/s gives C = 0.0423 bar1/2 and 12.9 m².[5] With the fixed 1998 constant, the SFPE Handbook obtained 13.6 m² for butane in the same room.[31] A 15 % higher burning velocity, from 40 to 46 cm/s, thus increases the required vent area by about 21 %.

Flame acceleration and detonation

A flame that cannot vent its products accelerates. In a closed duct the expanding products push the flame and the unburned gas forward, and the turbulence ahead of the flame raises the burning velocity further.[12] In a long enough duct a shock wave forms, and the flame becomes a detonation, typically travelling at 1500 to 3000 m/s.[12] A deflagration, by contrast, travels more slowly than sound, about 335 m/s in a lean fuel–air mixture.[34] The handbook lists mixture reactivity, expressed as burning velocity, as the first factor that governs the distance to the deflagration-to-detonation transition in a pipe.[35]

Burning velocity also helps to rank gases for the hazard of a vapour cloud explosion. Damaging overpressures in a virtually unconfined cloud require flame speeds of the order of 100 m/s.[36] Gases with large laminar burning velocities, and those prone to flame acceleration, are more likely to be involved, such as propane, propylene, ethylene and aromatic hydrocarbons.[36] For dusts, the deflagration index KSt plays a role similar to that of burning velocity for gases.[35] It is in theory proportional to an equivalent turbulent burning velocity of the dust–air mixture.[32]

Limitations and uncertainty

Measured burning velocities scatter. Much of the difference between laboratories comes from how the position of the flame front is defined, and from quenching near the burner rim.[9] For propane–air, reported maximum values lie mainly between 37 and 45 cm/s, and most within 41 ± 2 cm/s.[9] The handbook table gives 46 cm/s for propane and 40 cm/s for methane, while Beyler gives 0.52 and 0.45 m/s.[5][11] The handbook row printed as "Ethane (ethylene)" gives 80 cm/s, where the SFPE Handbook lists 68 cm/s for ethene–air.[5][9]

A tabulated value describes a laminar flame in a mixture at room temperature and atmospheric pressure, usually at the worst-case composition.[9][7] In a real explosion the unburned gas is compressed, heated and turbulent. The turbulence factor that links laboratory and plant cannot be predicted beforehand, and it is especially hard to estimate for vented explosions with flame instabilities.[27][37] With extreme turbulence, as in a hammer mill, the recommended vent constants can underestimate the pressure.[31]

The design equations here are those of NFPA 68 (2007 edition) as described in the 2008 handbook, and of the 1998 edition as described in the 2002 SFPE Handbook.[8][31] The venting-parameter equation is limited to burning velocities below 60 cm/s and to low-strength enclosures, so it does not cover hydrogen or acetylene.[8] A common misconception is to treat burning velocity and flame speed as the same thing. The flame speed seen by an observer is several times larger, and it depends on the enclosure and its contents as well as on the gas.[1][4]

See also

Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Schwab (2008b), p. 18-81.
  2. ↑ 2.0 2.1 2.2 Drysdale (2008), p. 2-13.
  3. ↑ 3.0 3.1 Iqbal and Salley (2004), p. F-10.
  4. ↑ 4.00 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 Zalosh (2002), p. 3-408.
  5. ↑ 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Schwab (2008b), p. 18-82, Table 18.6.3.
  6. ↑ Zalosh (2008), p. 2-98.
  7. ↑ 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 Zalosh (2002), p. 3-407.
  8. ↑ 8.0 8.1 8.2 8.3 8.4 8.5 8.6 Schwab (2008b), p. 18-84.
  9. ↑ 9.00 9.01 9.02 9.03 9.04 9.05 9.06 9.07 9.08 9.09 9.10 9.11 9.12 9.13 9.14 9.15 9.16 Simmons (2002), p. 1-146.
  10. ↑ 10.0 10.1 10.2 10.3 Simmons (2002), p. 1-144.
  11. ↑ 11.0 11.1 11.2 Beyler (2002a), p. 3-303.
  12. ↑ 12.0 12.1 12.2 12.3 12.4 Simmons (2002), p. 1-147.
  13. ↑ Van Rossum (2027), §4.3.
  14. ↑ Drysdale (2008), p. 2-19.
  15. ↑ Iqbal and Salley (2004), p. 3-12.
  16. ↑ 16.0 16.1 16.2 Simmons (2002), p. 1-148.
  17. ↑ Simmons (2002), p. 1-150.
  18. ↑ Yu and Newman (2008), p. 2-81.
  19. ↑ Van Rossum (2027), §4.10.
  20. ↑ Benedetti (2008), p. 6-4.
  21. ↑ Lemoff (2008), p. 6-181.
  22. ↑ Iqbal and Salley (2004), p. 16-2.
  23. ↑ Drysdale (2008), p. 2-16.
  24. ↑ Beyler (2002b), p. 2-179.
  25. ↑ 25.0 25.1 Ural and Garzia (2008), p. 17-143.
  26. ↑ 26.0 26.1 26.2 26.3 26.4 Zalosh (2008), p. 2-99.
  27. ↑ 27.0 27.1 27.2 27.3 27.4 27.5 Zalosh (2002), p. 3-409.
  28. ↑ Zalosh (2002), p. 3-410.
  29. ↑ Schwab (2008b), p. 18-83.
  30. ↑ 30.0 30.1 Schwab (2008b), p. 18-85.
  31. ↑ 31.0 31.1 31.2 31.3 31.4 Zalosh (2002), p. 3-416.
  32. ↑ 32.0 32.1 Ural and Garzia (2008), pp. 17-146–17-147.
  33. ↑ Ural and Garzia (2008), p. 17-162.
  34. ↑ Zalosh (2008), p. 2-94.
  35. ↑ 35.0 35.1 Zalosh (2008), p. 2-100.
  36. ↑ 36.0 36.1 Zalosh (2008), p. 2-104.
  37. ↑ Zalosh (2002), p. 3-415.

References

  • Benedetti, R. P. (2008). Fire hazards of materials. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-3–6-9). National Fire Protection Association.
  • Beyler, C. L. (2002a). Fire hazard calculations for large, open hydrocarbon fires. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-268–3-314). National Fire Protection Association; Society of Fire Protection Engineers.
  • Beyler, C. L. (2002b). Flammability limits of premixed and diffusion flames. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-172–2-187). National Fire Protection Association; Society of Fire Protection Engineers.
  • Drysdale, D. (2008). Physics and chemistry of fire. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-3–2-20). National Fire Protection Association.
  • Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
  • Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
  • Schwab, R. F. (2008b). Deflagration (explosion) venting. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 18-79–18-88). National Fire Protection Association.
  • Simmons, R. F. (2002). Premixed burning. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 1-144–1-154). National Fire Protection Association; Society of Fire Protection Engineers.
  • Ural, E. A., & Garzia, H. W. (2008). Explosion prevention and protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-141–17-165). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
  • Yu, H.-Z., & Newman, J. S. (2008). Theory of fire extinguishment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-79–2-92). National Fire Protection Association.
  • Zalosh, R. (2002). Explosion protection. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-402–3-421). National Fire Protection Association; Society of Fire Protection Engineers.
  • Zalosh, R. (2008). Explosions. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-93–2-106). National Fire Protection Association.