Contents
Community right-to-know is the US system of federal rules under which facilities must tell local emergency planners and fire departments which hazardous chemicals they hold and release. The information is then made available to the public on request.[1] Its legal basis is the Emergency Planning and Community Right-to-Know Act of 1986 (EPCRA), which is Title III of the Superfund Amendments and Reauthorization Act (SARA Title III).[2][3] The Act created state emergency response commissions and local emergency planning committees. It also set up four groups of duties: emergency planning, emergency release notification, community right-to-know reporting and a toxic chemical release inventory.[2]
In a narrow sense, the term refers to the reporting duties of Sections 311 and 312. Under these, facilities submit safety data sheets and chemical inventories to the planning committee, the state commission and the local fire department.[1] Fire departments are expected to use the reports in pre-incident planning and in budgeting for equipment.[3] The rules described here are those of the United States as summarised in the Fire Protection Handbook (20th edition, 2008), not current or international requirements.
Definition and scope
The handbook uses "community right-to-know" in two ways. Denlinger applies the name to the whole Act: the "Community Right-to-Know" provisions require facilities that hold chemicals above certain quantities to report what they have on the premises to the local fire department.[3] Hildebrand and Noll call the Act the Right-to-Know Act of 1986 and reserve the heading "community right-to-know reporting requirements" for Sections 311 and 312.[2]
Community right-to-know should be distinguished from the worker's right to know. The OSHA Hazard Communication Standard, 29 CFR 1910.1200, is also commonly called the right-to-know law, or HAZCOM.[4] That standard, issued by the Occupational Safety and Health Administration (OSHA), makes the sheets available to employees who ask for information about a chemical in the workplace.[4] Under EPCRA, the same sheets go to the LEPC, the SERC and the fire department, and members of the public can request them from the LEPC.[1] The two are linked, because Sections 311 and 312 apply to the chemicals for which OSHA requires a safety data sheet.[1]
The Environmental Protection Agency (EPA) sets the Section 312 thresholds and receives the Section 313 release reports.[1][5] Schmidt lists them in the Code of Federal Regulations as 40 CFR 355, Emergency Planning and Notification, and 40 CFR 370, Hazardous Chemical Reporting: Community Right-to-Know.[6] He places them among the federal regulations relevant to emergency management and business continuity.[6]
Origins
According to Hildebrand and Noll, Congress has enacted hazardous materials laws in response to specific catastrophes, such as Love Canal in New York, Bhopal in India and the terrorist attacks of 11 September 2001.[7] SARA, passed in 1986, amended and reauthorised the Superfund law of 1980 (CERCLA). Many of its amendments dealt with hazardous waste site cleanup, but SARA also set a national baseline for hazardous materials planning, preparedness, training and response.[2] Hildebrand and Noll consider it the law with the greatest impact on hazardous materials emergency planning and response.[2]
Title I of SARA led OSHA to develop the Hazardous Waste Operations and Emergency Response standard (HAZWOPER, 29 CFR 1910.120), covering worker groups who handle or respond to chemical emergencies, including at hazardous waste sites.[2] Title III is the part most familiar to the emergency response community.[2] Severson summarises SARA as a law that sets requirements in Title III for the public disclosure of chemical information and for the development of emergency response plans.[8]
| Sections | Subject | Main duty |
|---|---|---|
| 301–303 | Emergency planning | States appoint commissions; local committees prepare and update emergency response plans |
| 304 | Emergency release notification | Facilities notify the local committee and the state commission of off-site releases |
| 311–312 | Community right-to-know reporting | Facilities submit safety data sheets and annual chemical inventories |
| 313 | Toxic chemical release inventory | Certain facilities report annual releases of listed toxic chemicals to the EPA |
Emergency planning
Sections 301 to 303 required the governor of each state to appoint a state emergency response commission (SERC). The commission designates local emergency planning districts and appoints a local emergency planning committee (LEPC) for each.[2] The committee must include elected state and local officials and members of fire, police, civil defence and public health organisations. Environmental, hospital and transportation officials and representatives of industry, business, the community and the media are also required members.[2]
The main task of the committee is to prepare an emergency response plan and submit it to the state commission, which approves it or returns it with recommendations. The plan must be revised and updated every year.[2] It must identify the sites and transport corridors where extremely hazardous materials are stored, used or transported, and set out the response and notification procedures. It must name a community coordinator and facility coordinators. It must also describe how a release and its probable affected area and population are determined, list the response equipment and resources, and contain evacuation plans, a training programme and a schedule of exercises.[2]
Snyder describes the same committees from the industrial side. They were formed to develop pre-emergency plans and include representatives of every plant that falls under the reporting requirements. Each committee should have a pre-emergency plan for each covered facility, showing which agencies will respond.[9] The role of an industrial fire brigade depends partly on these plans.[9]
New York City offers an example. A 1996 Fire Department of New York document, reproduced in the NIST investigation of the World Trade Center disaster, lists the functions of the Mayor's Office of Emergency Management. One of them is to coordinate the operation of the local committee established under SARA Title III.[10]
Emergency release notification
Section 304 requires the owner or operator of a facility to notify the LEPC's community emergency coordinator and the SERC immediately of certain releases. These are releases of a listed hazardous substance that extend beyond the facility's property and may endanger the public. In most communities the first call goes to the 9-1-1 emergency number.[2] The term "facility" is defined broadly. It includes buildings, pipes and pipelines, wells, ponds, storage containers, motor vehicles, rolling stock and aircraft, but not consumer products or waterborne vessels.[2]
Releases that expose only people on the site itself need not be reported to the LEPC or SERC, although they may have to be reported to the National Response Center under CERCLA. The substances concerned are on two lists: about 360 extremely hazardous substances in 40 CFR 355 and about 725 substances under CERCLA Section 103(a).[2] The first notice must, as far as known, give the identity of the substance, whether it is extremely hazardous, the quantity released, the time and duration of the release and the medium affected. It must also state the known health risks, the precautions to take, such as evacuation, and a contact person.[2] A written follow-up describes the actions taken, the health risks and any medical advice.[1]
Hazardous chemical reporting
Section 311 requires a facility to prepare or have available a safety data sheet for each hazardous chemical covered by OSHA rules. It must submit the sheets to the LEPC, the SERC and the fire department with jurisdiction.[1] Instead of the sheets, the facility may submit a list of the chemicals grouped by OSHA health and physical hazard categories. A revised sheet is due within three months of significant new information. Members of the public can ask the LEPC for the sheet of any chemical submitted to it.[1]
Section 312 adds an annual emergency and hazardous chemical inventory, sent to the same three bodies. It covers every hazardous chemical present above the thresholds at any time in the previous calendar year.[1] The Tier I form gives, for each OSHA hazard category, the maximum and average daily amounts in ranges and the general location. The categories are fire, sudden release of pressure, reactivity, acute health hazard and chronic health hazard, and the form is due on or before 1 March.[1]
A Tier II form is required if the SERC, the LEPC or the fire department asks for it, and it replaces the Tier I form.[1] Tier II lists each chemical by name, with its maximum and average daily amounts, the manner of storage and its location at the facility. It also states whether the owner withholds the location from public disclosure.[11] On request, the owner must allow the fire department an on-site inspection and give it the specific locations of the hazardous chemicals.[5]
| Chemical group | Threshold (as printed) | SI value |
|---|---|---|
| Extremely hazardous substances | 500 lb, or the threshold planning quantity if lower | 227 kg, or lower |
| All other hazardous chemicals for which OSHA requires a safety data sheet | 10,000 lb | 4,536 kg |
A worked example shows how the thresholds apply. Consider three stores at one site during the previous year. A store of 300 kg of an extremely hazardous substance exceeds 227 kg and must be reported, whatever its threshold planning quantity, because the lower of the two values applies.[1] A store of 4,000 kg of an ordinary solvent covered by OSHA rules is below 4,536 kg and needs no Section 312 report. A warehouse holding 6,000 kg of a covered pesticide product is above the threshold and must be reported. Section 311 duties for the safety data sheets apply separately when chemicals are present at or above the established thresholds.[1]
Toxic chemical release inventory
Section 313 requires certain facilities to file an annual Toxic Chemical Release Inventory Form (Form R) with the EPA and with officials designated by the state governor, on or before 1 July.[5] A release is defined broadly, from spilling, leaking and emitting to dumping, disposing and the abandonment of closed containers. The section applies to facilities with 10 or more full-time employees in Standard Industrial Classification codes 20 to 39. These facilities must have manufactured or processed more than 11,340 kg (25,000 lb), or otherwise used more than 4,536 kg (10,000 lb), of a listed chemical in the previous year.[5][12]
A chemical can be added to the list if it can cause significant acute health effects beyond the site boundary, or chronic effects such as cancer, or significant environmental effects through toxicity, persistence or bioaccumulation.[5] According to Severson, the EPA used this programme, expanded under the Pollution Prevention Act of 1990, to collect data on more than 570 listed toxic chemicals and 30 chemical categories from over 23,000 companies. In 2003 the reporting facilities released 2.3 billion kg (5.0 billion lb) of listed chemicals on site and off site.[12] The resulting public database is intended to help answer questions about toxic chemical releases in a community. The EPA uses it to target pollution problem areas and as a screening tool in developing regulations, guidelines and standards, and researchers can access it.[5]
Use by fire departments
For the fire service, the main value of community right-to-know lies in planning. Denlinger states that fire departments should receive the reports and use them for effective pre-incident plans and for budgeting for appropriate equipment.[3] He also advises fire departments to keep a close working relationship with the LEPC and other planning bodies.[13] Jenaway gives an example of how the information is used in needs assessment. The chemical names and safety data sheets distributed by the LEPC may show that large quantities of foam concentrate or extensive spill control and diking equipment are needed.[14] Under the hazardous waste rules, fire officials and LEPCs can also obtain from the EPA regional office a list of the hazardous waste generators in their area.[15]
Hildebrand and Noll describe the reporting duties as a bridge between planning and prevention. They note that many state regulations are similar in scope and often exceed the federal requirements.[7] LEPC plans also indicate which agencies will respond to each covered facility, which links the reports to hazardous materials response.[9]
Facility managers have matching duties. Whitford, writing about pesticide storage, advises checking the chemicals stored on site against the EPCRA list of reportable products. If a pesticide on the list is stored above its reportable quantity, the facility must report to the local fire department, the SERC and the LEPC.[16] Management should know the requirements, file all reports, complete an emergency response preplan with the local fire authorities and take an active part in the LEPC.[16] A consolidated EPA "List of Lists" brings together the chemicals regulated under CERCLA, SARA Title III, EPCRA and the Clean Water Act, with the quantities above which storage must be reported.[17]
Community right-to-know sits beside other US programmes based on risk. Barry notes that EPA regulations under the Clean Air Act Amendments of 1990 may require facilities with threshold amounts of hazardous materials to develop risk assessment and risk management programmes. State laws in California, New Jersey and Delaware increasingly required quantitative risk assessment, with an emphasis on risk reduction and emergency planning.[18] The same amendments required certain facilities to make information available to the public on how chemical risks are handled.[15]
Limits and common misconceptions
The rules are thresholds, not a full inventory. Chemicals below the Section 312 thresholds are not reported, and releases that expose only people on the site are not reported to the LEPC or SERC.[2][1] A Tier II report may also withhold the location of a specific chemical from public disclosure, although the fire department can still obtain it on request.[11][5]
A common confusion is between community right-to-know under EPCRA and the worker right-to-know of the OSHA Hazard Communication Standard. Both are called right-to-know laws, but they serve different audiences.[4] Hildebrand and Noll also warn that the overlapping federal laws produce no fewer than six legal definitions of a hazardous material, which makes code enforcement confusing.[19]
The handbook is not fully consistent in its metric conversions. Hildebrand and Noll print 10,000 lb as 4450 kg and 25,000 lb as 11,350 kg, whereas Severson gives 4536 kg and 11,340 kg, which agree with the exact conversion.[1][5][12] Finally, all values and duties in this article describe US federal law as summarised in 2008. They are not universal requirements.
See also
Notes
- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 Hildebrand and Noll (2008), p. 13-86.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 Hildebrand and Noll (2008), p. 13-85.
- ↑ 3.0 3.1 3.2 3.3 Denlinger (2008), p. 12-59.
- ↑ 4.0 4.1 4.2 Hildebrand and Noll (2008), p. 13-90.
- ↑ 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 Hildebrand and Noll (2008), p. 13-87.
- ↑ 6.0 6.1 Schmidt (2008), p. 1-139.
- ↑ 7.0 7.1 Hildebrand and Noll (2008), p. 13-83.
- ↑ Severson (2008), p. 7-59.
- ↑ 9.0 9.1 9.2 Snyder (2008), p. 12-197.
- ↑ Lawson and Vettori (2005), Appendix L.
- ↑ 11.0 11.1 Hildebrand and Noll (2008), pp. 13-86–13-87.
- ↑ 12.0 12.1 12.2 Severson (2008), pp. 7-57–7-58.
- ↑ Denlinger (2008), p. 12-78.
- ↑ Jenaway (2008), p. 12-48.
- ↑ 15.0 15.1 Hildebrand and Noll (2008), p. 13-84.
- ↑ 16.0 16.1 Whitford (2008), p. 6-243.
- ↑ Whitford (2008), pp. 6-235–6-236.
- ↑ Barry (2002), p. 5-176.
- ↑ Hildebrand and Noll (2008), p. 13-81.
References
- Barry, T. F. (2002). Quantitative risk assessment in chemical process industries. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 5-176–5-213). National Fire Protection Association; Society of Fire Protection Engineers.
- Denlinger, R. F. (2008). Managing fire-rescue departments. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-51–12-78). National Fire Protection Association.
- Hildebrand, M. S., & Noll, G. G. (2008). Public fire protection and hazmat management. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-81–13-98). National Fire Protection Association.
- Jenaway, W. F. (2008). Needs assessment and hazard analysis. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-41–12-50). National Fire Protection Association.
- Lawson, J. R., & Vettori, R. L. (2005). The emergency response operations (NIST NCSTAR 1-8). National Institute of Standards and Technology.
- Schmidt, D. L. (2008). Emergency management and business continuity. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 1-137–1-156). National Fire Protection Association.
- Severson, P. R. (2008). Hazardous waste control. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-57–7-69). National Fire Protection Association.
- Snyder, M. (2008). Industrial fire loss prevention. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-177–12-198). National Fire Protection Association.
- Whitford, F. (2008). Pesticides in the workplace. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-233–6-245). National Fire Protection Association.