Skip to content
From Fire Safety Academy Wiki
Daan (talk | contribs)
Refine sentence flow and printed-page reference locators (written by GPT-6)
Mark (talk | contribs)
Add SVG figures fse-fire-pump-performance-curve-v1.svg, fse-fire-pump-performance-curve-v2.svg, fse-fire-pump-performance-curve-v3.svg (list-5 visual plan)
Line 5: Line 5:
== Reading a performance curve ==
== Reading a performance curve ==
[[Hydraulic calculation]] uses the [[Fire pump|fire pump]] curve together with the system demand; the [[Fire water supply|fire water supply]] may already provide positive inlet pressure, which must be distinguished from the pump's added head. A [[Water supply curve|water supply curve]] describes the source at a stated reference point. The two curves are combined through the physical route rather than by adding nameplate pressures without reference to flow. <ref name="T_4-68_4-70" /><ref name="F_4-81_4-82">Fleming (2002), ch. 4-3, pp. 4-81–4-82.</ref>
[[Hydraulic calculation]] uses the [[Fire pump|fire pump]] curve together with the system demand; the [[Fire water supply|fire water supply]] may already provide positive inlet pressure, which must be distinguished from the pump's added head. A [[Water supply curve|water supply curve]] describes the source at a stated reference point. The two curves are combined through the physical route rather than by adding nameplate pressures without reference to flow. <ref name="T_4-68_4-70" /><ref name="F_4-81_4-82">Fleming (2002), ch. 4-3, pp. 4-81–4-82.</ref>
[[File:fse-fire-pump-performance-curve-v1.svg|thumb|upright=1.5|alt=Fire pump performance curve: functional relationships. Measurement and water paths are distinct.|Fire pump performance curve: functional relationships. Schematic explanation; dimensions are not installation instructions.]]


A [[Hydrant flow test|hydrant flow test]] can provide evidence about the incoming supply; it does not directly measure the differential performance of the installed pump. Pump observations need suction and discharge conditions, speed and a measured flow. [[Net positive suction head]] provides another limit that can become more demanding as the operating flow increases. <ref name="H_15_6_15-89_15-92">Cote (2008), ch. 15.6, pp. 15-89–15-92.</ref><ref name="F_4-81_4-82" />
A [[Hydrant flow test|hydrant flow test]] can provide evidence about the incoming supply; it does not directly measure the differential performance of the installed pump. Pump observations need suction and discharge conditions, speed and a measured flow. [[Net positive suction head]] provides another limit that can become more demanding as the operating flow increases. <ref name="H_15_6_15-89_15-92">Cote (2008), ch. 15.6, pp. 15-89–15-92.</ref><ref name="F_4-81_4-82" />
Line 12: Line 13:
== Pump operation and selection ==
== Pump operation and selection ==
A centrifugal pump transfers shaft energy to water through a rotating impeller; its performance varies with flow, speed and pump geometry. The selected duty belongs on a curve showing this relationship, rather than being defined by a single pressure reading. The complete operating point also depends on the resistance and supply conditions of the connected installation. <ref name="H_15_6_15-85_15-89_15-92">Cote (2008), ch. 15.6, pp. 15-85,15-89–15-92.</ref><ref name="T_4-67_4-69">Titus (2002), ch. 4-2, pp. 4-67–4-69.</ref>
A centrifugal pump transfers shaft energy to water through a rotating impeller; its performance varies with flow, speed and pump geometry. The selected duty belongs on a curve showing this relationship, rather than being defined by a single pressure reading. The complete operating point also depends on the resistance and supply conditions of the connected installation. <ref name="H_15_6_15-85_15-89_15-92">Cote (2008), ch. 15.6, pp. 15-85,15-89–15-92.</ref><ref name="T_4-67_4-69">Titus (2002), ch. 4-2, pp. 4-67–4-69.</ref>
[[File:fse-fire-pump-performance-curve-v2.svg|thumb|upright=1.5|alt=Pump and installed system. Measurement and water paths are distinct.|Pump and installed system. Schematic explanation; dimensions are not installation instructions.]]


The pump head is the energy added across the pump; discharge pressure alone is not that quantity when suction pressure, elevation or velocity differ between measuring points. Horizontal pumps and vertical turbine arrangements require appropriate references for their respective configurations. A test comparison can be misleading if the water level or suction reference has changed without being recorded. <ref name="H_15_6_15-89_15-90">Cote (2008), ch. 15.6, pp. 15-89–15-90.</ref>
The pump head is the energy added across the pump; discharge pressure alone is not that quantity when suction pressure, elevation or velocity differ between measuring points. Horizontal pumps and vertical turbine arrangements require appropriate references for their respective configurations. A test comparison can be misleading if the water level or suction reference has changed without being recorded. <ref name="H_15_6_15-89_15-90">Cote (2008), ch. 15.6, pp. 15-89–15-90.</ref>
Line 25: Line 27:
== Comparing supply and demand ==
== Comparing supply and demand ==
Supply and demand curves answer complementary questions; a supply curve gives the pressure available at different flows under stated conditions. A demand calculation gives the pressure needed to deliver the selected flow through the protection system. Their comparison is meaningful only at a common reference point and for compatible operating assumptions. <ref name="F_4-81_4-83">Fleming (2002), ch. 4-3, pp. 4-81–4-83.</ref>
Supply and demand curves answer complementary questions; a supply curve gives the pressure available at different flows under stated conditions. A demand calculation gives the pressure needed to deliver the selected flow through the protection system. Their comparison is meaningful only at a common reference point and for compatible operating assumptions. <ref name="F_4-81_4-83">Fleming (2002), ch. 4-3, pp. 4-81–4-83.</ref>
[[File:fse-fire-pump-performance-curve-v3.svg|thumb|upright=1.5|alt=Recalculated pressure-flow example. Measurement and water paths are distinct.|Recalculated pressure-flow example. Schematic explanation; dimensions are not installation instructions.]]


A common water-supply approximation treats the pressure drop from the test's static value as proportional to flow raised to the power 1.85. The relation can interpolate a measured pressure-flow pair and supports the traditional transformed-axis graph. It is an empirical representation of a network, not a physical guarantee at every extrapolated flow. <ref name="F_4-81">Fleming (2002), ch. 4-3, pp. 4-81.</ref><ref name="T_4-52_4-53">Titus (2002), ch. 4-2, pp. 4-52–4-53.</ref>
A common water-supply approximation treats the pressure drop from the test's static value as proportional to flow raised to the power 1.85. The relation can interpolate a measured pressure-flow pair and supports the traditional transformed-axis graph. It is an empirical representation of a network, not a physical guarantee at every extrapolated flow. <ref name="F_4-81">Fleming (2002), ch. 4-3, pp. 4-81.</ref><ref name="T_4-52_4-53">Titus (2002), ch. 4-2, pp. 4-52–4-53.</ref>

Revision as of 19:50, 12 November 2026

Fire pump performance curve is a graph relating a fire pump's delivered flow to its developed head under stated operating conditions. [1][2] The curve identifies how a pump behaves between shutoff and high-flow operation. Efficiency, shaft power and required suction head provide related but different information. The actual installed operating point also depends on available inlet pressure and the resistance of the connected system. [3]

The engineering assessment combines the source, pump, driver, controls and delivery route. Static pressure is only one observation within that chain. Flowing performance, maximum pressure and the capacity to continue for the required duration answer different questions. Records of the installed arrangement and suitable tests connect the calculated duty to the equipment that must operate during a fire. [4][5] Starting tests and flowing tests exercise different functions. [5]

Reading a performance curve

Hydraulic calculation uses the fire pump curve together with the system demand; the fire water supply may already provide positive inlet pressure, which must be distinguished from the pump's added head. A water supply curve describes the source at a stated reference point. The two curves are combined through the physical route rather than by adding nameplate pressures without reference to flow. [3][6]

Fire pump performance curve: functional relationships. Measurement and water paths are distinct.
Fire pump performance curve: functional relationships. Schematic explanation; dimensions are not installation instructions.

A hydrant flow test can provide evidence about the incoming supply; it does not directly measure the differential performance of the installed pump. Pump observations need suction and discharge conditions, speed and a measured flow. Net positive suction head provides another limit that can become more demanding as the operating flow increases. [7][6]

The shape of the curve influences both minimum useful delivery and maximum system pressure; shutoff head matters when little or no water is discharged. A high-flow point matters when the fire demand approaches the available capacity. Driver power and suction adequacy must remain acceptable across the intended range, not merely where the rated point is marked. [8]

Pump operation and selection

A centrifugal pump transfers shaft energy to water through a rotating impeller; its performance varies with flow, speed and pump geometry. The selected duty belongs on a curve showing this relationship, rather than being defined by a single pressure reading. The complete operating point also depends on the resistance and supply conditions of the connected installation. [9][10]

Pump and installed system. Measurement and water paths are distinct.
Pump and installed system. Schematic explanation; dimensions are not installation instructions.

The pump head is the energy added across the pump; discharge pressure alone is not that quantity when suction pressure, elevation or velocity differ between measuring points. Horizontal pumps and vertical turbine arrangements require appropriate references for their respective configurations. A test comparison can be misleading if the water level or suction reference has changed without being recorded. [11]

A centrifugal pump normally develops its greatest head near shutoff and less head at higher flows; the closed-outlet condition therefore needs assessment for maximum system pressure. At the other end of the operating range, the remaining head must meet the required discharge pressure after losses. Driver capability and suction conditions can constrain operation even where the plotted head appears adequate. [8][1]

The handbook's account of United States NFPA 20 practice describes a rated point, a high-flow point and a shutoff limit. It reports at least 65% of rated head at 150% of rated flow, with shutoff head no greater than 140%. These are historical criteria reported in the 2008 handbook. They are not a substitute for a selected pump's actual curve or a statement of a current adopted standard. [12]

Connecting pumps in series adds their heads at a common flow; connecting them in parallel combines flow at a common head. Neither arrangement automatically doubles delivery through the installed network, because the operating intersection changes. Shared suction piping and power dependencies also remain part of the installation rather than disappearing through duplication. [13][14]

The water source must be assessed alongside the pump; a booster can overcome insufficient pressure but cannot create an absent water reserve. A powerful driver cannot correct an obstructed intake or inadequate suction conditions. Selection therefore brings together the source, suction route, performance curve, driver, controls and downstream demand. [15][1]

Comparing supply and demand

Supply and demand curves answer complementary questions; a supply curve gives the pressure available at different flows under stated conditions. A demand calculation gives the pressure needed to deliver the selected flow through the protection system. Their comparison is meaningful only at a common reference point and for compatible operating assumptions. [16]

Recalculated pressure-flow example. Measurement and water paths are distinct.
Recalculated pressure-flow example. Schematic explanation; dimensions are not installation instructions.

A common water-supply approximation treats the pressure drop from the test's static value as proportional to flow raised to the power 1.85. The relation can interpolate a measured pressure-flow pair and supports the traditional transformed-axis graph. It is an empirical representation of a network, not a physical guarantee at every extrapolated flow. [17][18]

p(Q)=ps−(ps−pr)(QQt)1.85

Symbol Description Unit
ps,pr Static and test residual pressures kPa
Qt Measured test discharge L/min
Q,p(Q) Investigated flow and predicted pressure L/min; kPa

Using the pressure and flow inputs in Fleming's printed example gives a useful arithmetic check; converted to SI, they are approximately 689 kPa static and 552 kPa residual at 3,785 L/min. At 1,703 L/min, the equation gives approximately 658 kPa. This recalculation uses the stated inputs; it does not reproduce the inconsistent intermediate answer printed in that example. [17]

A pump adds a further pressure-flow relationship; the available inlet pressure combines with the differential head developed by the pump, after appropriate elevation and velocity corrections. The resulting supply is not obtained by adding the rated pump pressure at every flow. Both high-flow delivery and low-flow maximum pressure need consideration. [3][19]

The calculation must also preserve the difference between capacity and duration; a source may meet a demand point initially while exhausting a finite reserve too soon. Two paths may appear redundant while sharing one vulnerable source or connecting segment. Pressure-flow agreement is therefore one part of demonstrating the performance of the complete supply arrangement. [20][21]

Suction conditions and cavitation

Water approaching an impeller must retain enough absolute pressure to avoid excessive vapour formation; pressure falls as flow accelerates through the inlet region. If local pressure reaches the water's vapour pressure, bubbles can form and subsequently collapse in higher-pressure regions. This cavitation can produce noise, vibration, loss of performance and material damage. [22][23]

Available net positive suction head describes the installation's suction energy above vapour-pressure head; required net positive suction head describes a pump characteristic supplied by the manufacturer for stated operating conditions. The two quantities must be compared at the relevant flow and speed. They are not two alternative names for a suction gauge reading. [2][23]

For a large open reservoir, the following form separates atmospheric pressure, water level and suction losses; the reservoir surface velocity is treated as negligible. A positive elevation difference means that the water surface is above the pump reference. A lower surface contributes a negative term. [23]

NPSHa=pa−pvρg+zs−zp−hs

Symbol Description Unit
NPSHa Available net positive suction head m
pa,pv Absolute atmospheric and vapour pressures Pa
ρ,g Water density and gravitational acceleration kg/m³; m/s²
zs,zp,hs Surface elevation, pump elevation and suction loss m

The lowest usable tank level can be more demanding than the initial full condition; a greater flow increases suction-pipe loss and can also increase the pump's required suction head. Warmer water increases vapour pressure, while atmospheric pressure varies with elevation. These effects explain why a universal maximum suction lift cannot represent every installation. [24][23]

The handbook illustrates a pump requiring approximately 3.05 m of suction head at 7,570 L/min and 5.49 m at 11,400 L/min. These are converted values from one illustrative manufacturer's-style curve, not general acceptance limits. Their significance is the changing requirement as flow rises. The appropriate comparison uses the actual pump data and the available head under the corresponding supply condition. [22]

Driver power and operating range

Hydraulic power is the rate at which energy is transferred to water; shaft power must also cover the pump's losses, so it exceeds hydraulic power whenever efficiency is below unity. The required driver rating depends on the relevant operating range. Selecting only from the nominal duty point can miss a greater shaft-power demand elsewhere on the curve. [25]

For flow expressed in litres per minute and differential pressure in kilopascals, the following equation gives shaft power in kilowatts; the conversion factor incorporates both the litre and minute conversions. Efficiency is a fraction, not a percentage inserted as a whole number. The equation assumes that the stated pressure represents the pump's added hydraulic energy consistently. [26][23]

Ps=QΔp60000η

Symbol Description Unit
Ps Required shaft power kW
Q Pump flow L/min
Δp Equivalent differential pressure kPa
η Pump efficiency dimensionless

The handbook gives an SI example based on a pump rated at 4,000 L/min and 700 kPa. It evaluates a higher-flow condition of 6,400 L/min at 385 kPa, with efficiency assumed to be 0.65. Substitution gives 63.2 kW of shaft power. This is a calculation at the stated illustrative condition, not a complete driver selection or an additional operating allowance. [26]

An electric installation must provide both starting and running capability; the controller, conductors and power arrangement therefore have duties beyond the motor's nominal output. A diesel installation avoids reliance on normal external electrical power for running, but needs fuel, starting capability, cooling and ventilation. Independence from one supply does not remove these other dependencies. [27][28]

Changes in speed also change pump behaviour; for the same impeller under affinity-law assumptions, flow scales with speed, head with its square and power with its cube. A small speed change can therefore alter power more strongly than flow. These relationships support interpretation, while the selected equipment's permitted operating envelope remains a separate constraint. [2]

Pressure, flow and energy

Water pressure describes only one part of the energy available in a pipe; elevation contributes potential energy, while movement contributes velocity head. Titus describes these quantities using head, expressed as an equivalent height of water. A hydraulic calculation must therefore compare locations through a common energy balance, rather than subtracting unrelated gauge readings. [29]

For steady, incompressible flow, the energy balance adds pump head and subtracts irreversible losses between two sections; the following form assumes that section-average velocity adequately represents kinetic energy. It describes a defined flow path, with all elevations measured from the same datum. Sudden changes require a different, transient analysis. [30]

p1ρg+v122g+z1+Hp=p2ρg+v222g+z2+hL

Symbol Description Unit
p Pressure at the section Pa
ρ Water density kg/m³
g Gravitational acceleration m/s²
v Mean velocity m/s
z,Hp,hL Elevation, added pump head and head loss m

Pressure can decrease because water rises, because velocity increases, or because energy is dissipated; these effects have different physical meanings. An elevation change can be recovered on a descending route, whereas friction dissipates mechanical energy. A larger pipe can reduce friction but cannot remove the elevation difference between the source and the outlet. [31]

Continuity provides the corresponding flow constraint: volume flow equals cross-sectional area multiplied by mean velocity; the same flow moves faster through a smaller internal bore. At a junction, incoming and outgoing flows balance, while losses depend on the flow assigned to each connected segment. Nominal pipe size alone does not supply the internal diameter needed for this calculation. [30][32]

The pressure at a sprinkler is the pressure remaining after the complete upstream route has been considered; it is not the pressure indicated beside a remote pump or street hydrant. The route includes connecting mains, valves, elevation and distribution piping. Leaving out an inconvenient section creates an apparently favourable calculation without providing the corresponding water at the outlet. [33][34]

Measuring the available supply

A supply test relates an observed discharge to the pressure remaining elsewhere in the connected system; the initial static reading describes the condition before the test discharge begins. The residual reading describes the pressure while the measured discharge is flowing. Both belong to the same test arrangement and must be recorded with its location and operating conditions. [17][35]

The flowing outlet and the pressure observation have different functions; a pitot measurement in an appropriate free jet supports an estimate of outlet flow. A gauge at the residual hydrant measures pressure in the distribution system during that discharge. Substituting jet pressure for residual system pressure confuses two different physical quantities. [35][17]

The discharge estimate depends on outlet geometry and the coefficient representing its losses; a disturbed or nonuniform jet makes a single point reading less representative. Probe alignment and position also influence the measurement. For some discharge devices, a calibrated nozzle or suitable flowmeter provides a more appropriate method than applying a simple pitot relation. [35]

Test results describe a network state, rather than an unlimited promise of future supply; domestic demand, pumps, source levels and closed valves can change that state. The pressure reference must also be carried correctly to the building calculation. A test performed at a different elevation or upstream of additional resistance needs hydraulic interpretation before comparison with system demand. [36][16]

A main-drain test provides a different kind of evidence; the handbook uses changes from previous static and flowing readings to identify possible deterioration or obstruction. This is useful for detecting change, but it does not independently establish the full sprinkler demand. Test opening, supply state and instrument condition affect whether successive observations are comparable. [37]

Pump testing likewise separates a start test from a flow-performance test; running successfully without substantial discharge demonstrates some operating functions but does not establish the entire pump curve. Flowing observations across the relevant operating range give evidence about delivery capability. The handbook describes retaining records so that deterioration and the ability to meet system demand can be assessed. [5]

See also

Notes

  1. ↑ 1.0 1.1 1.2 Titus (2002), ch. 4-2, pp. 4-68–4-69.
  2. ↑ 2.0 2.1 2.2 Cote (2008), ch. 15.6, pp. 15-91–15-92.
  3. ↑ 3.0 3.1 3.2 Titus (2002), ch. 4-2, pp. 4-68–4-70.
  4. ↑ Cote (2008), ch. 15.6, pp. 15-89–15-99.
  5. ↑ 5.0 5.1 5.2 Cote (2008), ch. 16.11, pp. 16-220.
  6. ↑ 6.0 6.1 Fleming (2002), ch. 4-3, pp. 4-81–4-82.
  7. ↑ Cote (2008), ch. 15.6, pp. 15-89–15-92.
  8. ↑ 8.0 8.1 Cote (2008), ch. 15.6, pp. 15-91–15-98.
  9. ↑ Cote (2008), ch. 15.6, pp. 15-85,15-89–15-92.
  10. ↑ Titus (2002), ch. 4-2, pp. 4-67–4-69.
  11. ↑ Cote (2008), ch. 15.6, pp. 15-89–15-90.
  12. ↑ Cote (2008), ch. 15.6, pp. 15-92.
  13. ↑ Titus (2002), ch. 4-2, pp. 4-70.
  14. ↑ Cote (2008), ch. 15.6, pp. 15-93–15-95.
  15. ↑ Cote (2008), ch. 15.6, pp. 15-91–15-99.
  16. ↑ 16.0 16.1 Fleming (2002), ch. 4-3, pp. 4-81–4-83.
  17. ↑ 17.0 17.1 17.2 17.3 Fleming (2002), ch. 4-3, pp. 4-81.
  18. ↑ Titus (2002), ch. 4-2, pp. 4-52–4-53.
  19. ↑ Cote (2008), ch. 15.6, pp. 15-89–15-94.
  20. ↑ Fleming (2002), ch. 4-3, pp. 4-83–4-84.
  21. ↑ Hopkins et al. (2005), pp. xxxvii–xlii.
  22. ↑ 22.0 22.1 Cote (2008), ch. 15.6, pp. 15-91.
  23. ↑ 23.0 23.1 23.2 23.3 23.4 Titus (2002), ch. 4-2, pp. 4-68.
  24. ↑ Cote (2008), ch. 15.6, pp. 15-91–15-95.
  25. ↑ Cote (2008), ch. 15.6, pp. 15-97–15-98.
  26. ↑ 26.0 26.1 Cote (2008), ch. 15.6, pp. 15-98.
  27. ↑ Cote (2008), ch. 15.7, pp. 15-106,15-113–15-115.
  28. ↑ Cote (2008), ch. 15.6, pp. 15-98–15-99.
  29. ↑ Titus (2002), ch. 4-2, pp. 4-45–4-48.
  30. ↑ 30.0 30.1 Titus (2002), ch. 4-2, pp. 4-47–4-50.
  31. ↑ Titus (2002), ch. 4-2, pp. 4-47–4-52.
  32. ↑ Cote (2008), ch. 16.3, pp. 16-41–16-42.
  33. ↑ Fleming (2002), ch. 4-3, pp. 4-75–4-81.
  34. ↑ Hopkins et al. (2005), pp. xxxvii–xxxviii.
  35. ↑ 35.0 35.1 35.2 Cote (2008), ch. 15.3, pp. 15-46–15-47.
  36. ↑ Cote (2008), ch. 15.2, pp. 15-23–15-24.
  37. ↑ Cote (2008), ch. 16.11, pp. 16-210–16-211.

References

  • Cote, A. E. (Ed.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
  • Fleming, R. P. (2002). Automatic sprinkler system calculations. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-72–4-87). National Fire Protection Association.
  • Hopkins, M., Schoenrock, J., & Budnick, E. (2005). Fire suppression systems (NIST NCSTAR 1-4B). National Institute of Standards and Technology.
  • Titus, J. J. (2002). Hydraulics. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-44–4-71). National Fire Protection Association.