FSE wiki: Scoped fire-alarm requirements, historical adoption and Dutch law; clarified GFCI exceptions and gas grouping after source check (written by Claude Opus 5.5) |
Correct errors identified in the editorial review of 9 November 2026 |
||
| Line 6: | Line 6: | ||
The National Institute of Standards and Technology (NIST) investigated the World Trade Center disaster. Its report on fire alarm systems calls the NEC the universal U.S. baseline code for power cabling and hard wiring, including fire alarm wiring. For fire alarms, the NEC specifies how to install supporting cable and hardware, while the building code of the jurisdiction determines which devices and equipment a building needs, and where.<ref name="KeoughGrill-2" /> | The National Institute of Standards and Technology (NIST) investigated the World Trade Center disaster. Its report on fire alarm systems calls the NEC the universal U.S. baseline code for power cabling and hard wiring, including fire alarm wiring. For fire alarms, the NEC specifies how to install supporting cable and hardware, while the building code of the jurisdiction determines which devices and equipment a building needs, and where.<ref name="KeoughGrill-2" /> | ||
Neighbouring codes cover other parts of the electrical system. The National Electrical Safety Code, first | Neighbouring codes cover other parts of the electrical system. The National Electrical Safety Code, first issued in 1914 and now published by the Institute of Electrical and Electronics Engineers (IEEE), covers overhead and underground supply and communication lines of public utilities. In Canada, the Canadian Electrical Code of CSA International sets the minimum requirements and was prepared with due regard for the NEC.<ref name="Milatovich-8-137" /> The ''National Electrical Code Handbook'', published by NFPA with each edition, contains the full text with explanations, but it is not itself a code and has no force of law.<ref name="Milatovich-8-137" /> | ||
== History and development == | == History and development == | ||
The code was first issued under its present name in 1897.<ref name="Milatovich-8-137" /> The American Engineering Standards Committee, the forerunner of the American National Standards Institute (ANSI), first met | The code was first issued under its present name in 1897.<ref name="Milatovich-8-137" /> The American Engineering Standards Committee, the forerunner of the American National Standards Institute (ANSI), first met on 19 October 1918. The 1920 edition of NFPA 70 was one of the first documents it accepted and registered as an "American Standard". NFPA is accredited by ANSI, which requires every American National Standard to be reviewed at least every five years.<ref name="CoteGrant-1-62">Cote and Grant (2008), p. 1-62.</ref> The NEC itself is revised every three years by the National Electrical Code Committee, and it carries the joint designation ANSI/NFPA 70.<ref name="Milatovich-8-137" /> | ||
The code is written by volunteer committees. According to the 2008 handbook, NFPA had about 80,000 members and about 250 consensus technical committees responsible for about 300 safety documents.<ref name="CoteGrant-1-64">Cote and Grant (2008), p. 1-64.</ref> Such committees have a balanced representation of all affected interests, including users, manufacturers, labour, testing laboratories, enforcers and government officials. The handbook sees this as a strength of the U.S. voluntary consensus system, because it lets diverse factors be weighed before a requirement is agreed.<ref name="CoteGrant-1-57">Cote and Grant (2008), p. 1-57.</ref> NFPA 70 has numbered code-making panels: the author of the handbook's electrical chapter, for example, was a principal member of Code Making Panel 17 and past chair of Code Making Panel 20.<ref name="Milatovich-8-127" /> | The code is written by volunteer committees. According to the 2008 handbook, NFPA had about 80,000 members and about 250 consensus technical committees responsible for about 300 safety documents.<ref name="CoteGrant-1-64">Cote and Grant (2008), p. 1-64.</ref> Such committees have a balanced representation of all affected interests, including users, manufacturers, labour, testing laboratories, enforcers and government officials. The handbook sees this as a strength of the U.S. voluntary consensus system, because it lets diverse factors be weighed before a requirement is agreed.<ref name="CoteGrant-1-57">Cote and Grant (2008), p. 1-57.</ref> NFPA 70 has numbered code-making panels: the author of the handbook's electrical chapter, for example, was a principal member of Code Making Panel 17 and past chair of Code Making Panel 20.<ref name="Milatovich-8-127" /> | ||
| Line 73: | Line 73: | ||
| General purpose || UL 1581 vertical cable tray || 20 kW burner, grouped cables || Fire does not reach the top of a 2.4 m tray | | General purpose || UL 1581 vertical cable tray || 20 kW burner, grouped cables || Fire does not reach the top of a 2.4 m tray | ||
|- | |- | ||
| Riser (shaft or floor to floor) || UL 1666 || | | Riser (shaft or floor to floor) || UL 1666 || 154.5 kW burner, grouped cables, two-storey rig || Prevents the carrying of fire from floor to floor | ||
|- | |- | ||
| Plenum (ducts, air-handling spaces) || NFPA 262 (Steiner tunnel) || 88 kW burner, horizontal || Flame travel ≤ 1.52 m; peak optical density ≤ 0.5; average ≤ 0.15 | | Plenum (ducts, air-handling spaces) || NFPA 262 (Steiner tunnel) || 88 kW burner, horizontal || Flame travel ≤ 1.52 m; peak optical density ≤ 0.5; average ≤ 0.15 | ||
Revision as of 16:08, 9 November 2026
The National Electrical Code (NEC) is NFPA 70, the United States code for the installation of electrical wiring and equipment, published by the National Fire Protection Association (NFPA).[1] Its purpose is the practical safeguarding of persons and property from hazards arising from the use of electricity, chiefly fire caused by arcing or overheating and electric shock.[1][2] First issued under its present name in 1897 and revised every three years, it was described in the 2008 handbook as the world's most widely adopted code.[1][3] For fire alarm systems, building codes specify which systems are required, while the NEC governs their supporting cable and hardware.[4] The Fire Protection Handbook (2008) names its widespread use and enforcement as probably the primary reason why electrical systems are not among the leading causes of U.S. fires.[5] The provisions described here are those of the 2005 edition, as reproduced in that handbook.[6]
Scope and purpose
The 20th edition of the Fire Protection Handbook states that all electrical installations in the United States should be made, used and maintained in accordance with the NEC. Other NFPA standards apply in special situations, such as NFPA 70E for electrical safety in the workplace, NFPA 75 for information technology equipment, NFPA 79 for industrial machinery and NFPA 99 for health care facilities.[1] All standards for electrical equipment aim to prevent fires caused by arcing and overheating and to prevent accidental contact with live parts.[2] Electricity can cause a fire if an arc occurs or if equipment overheats, the two mechanisms of electrical ignition that the code addresses.[6]
The National Institute of Standards and Technology (NIST) investigated the World Trade Center disaster. Its report on fire alarm systems calls the NEC the universal U.S. baseline code for power cabling and hard wiring, including fire alarm wiring. For fire alarms, the NEC specifies how to install supporting cable and hardware, while the building code of the jurisdiction determines which devices and equipment a building needs, and where.[4]
Neighbouring codes cover other parts of the electrical system. The National Electrical Safety Code, first issued in 1914 and now published by the Institute of Electrical and Electronics Engineers (IEEE), covers overhead and underground supply and communication lines of public utilities. In Canada, the Canadian Electrical Code of CSA International sets the minimum requirements and was prepared with due regard for the NEC.[1] The National Electrical Code Handbook, published by NFPA with each edition, contains the full text with explanations, but it is not itself a code and has no force of law.[1]
History and development
The code was first issued under its present name in 1897.[1] The American Engineering Standards Committee, the forerunner of the American National Standards Institute (ANSI), first met on 19 October 1918. The 1920 edition of NFPA 70 was one of the first documents it accepted and registered as an "American Standard". NFPA is accredited by ANSI, which requires every American National Standard to be reviewed at least every five years.[7] The NEC itself is revised every three years by the National Electrical Code Committee, and it carries the joint designation ANSI/NFPA 70.[1]
The code is written by volunteer committees. According to the 2008 handbook, NFPA had about 80,000 members and about 250 consensus technical committees responsible for about 300 safety documents.[8] Such committees have a balanced representation of all affected interests, including users, manufacturers, labour, testing laboratories, enforcers and government officials. The handbook sees this as a strength of the U.S. voluntary consensus system, because it lets diverse factors be weighed before a requirement is agreed.[9] NFPA 70 has numbered code-making panels: the author of the handbook's electrical chapter, for example, was a principal member of Code Making Panel 17 and past chair of Code Making Panel 20.[6]
Requirements change from edition to edition, often after field experience. Ground-fault protection of equipment on large 480Y/277 V services was first required in the 1971 edition, because of an unusually high number of burndowns.[10] The Class B ground-fault circuit interrupter, which trips above 20 mA, may be used only for underwater pool lighting installed before local adoption of the 1965 edition.[11] The 2008 edition raised the fire resistance required for fire pump circuits routed through buildings from 1 to 2 hours, to match the 2-hour circuit survivability of NFPA 72.[12]
Adoption and enforcement
A model code is only a representation of possible regulations and does not become law until a state or municipal legislature enacts it.[3] The 2008 handbook reported NEC adoption in virtually every U.S. state, Mexico and several other countries.[3] In June 2005, NIST found that the NEC was used in virtually all U.S. jurisdictions. The federal government's role in setting specific codes is mandatory only for federally owned, leased, regulated or financed facilities, apart from manufactured housing.[13] NFPA codes are also referenced in federal regulations, including those of the U.S. Nuclear Regulatory Commission, the General Services Administration and the Occupational Safety and Health Administration.[14] Other codes refer to it as well: the elevator code ASME A17.1/CSA B44 requires elevator wiring to conform to NFPA 70, or in Canada to the Canadian Electrical Code.[15]
Adoption can be partial and lag behind publication. In its 2005 study of New York City fire alarm systems, NIST reported that the city's building code adopted sections of the NEC as a reference standard, not its full content. It referenced editions that were not the latest; the study noted that the code in effect when an alarm system was designed was generally applied through that system's life.[4] The same building code referred to the NEC for transformer vaults above 35,000 V, which required 3-hour fire resistance in both its 1968 and 2003 versions.[16]
Enforcement is in the hands of government agencies such as building departments and electrical inspectors.[8] The code leaves some decisions to this authority having jurisdiction (AHJ). For example, the code sets no maximum distance between the point where service conductors enter a building and the service disconnecting means, so the AHJ decides how far they may run inside.[17] Equipment is listed or labelled by testing laboratories such as Underwriters Laboratories (UL), Intertek, Factory Mutual and CSA. They test it for actual field use in accordance with the NEC and other American National Standards.[1]
Other countries use other systems. The NEC itself recognises a zone method of classifying hazardous locations, consistent with the rules of the International Electrotechnical Commission (IEC), in Article 505.[18] A 2021 Dutch study described Article 6.8 of the 2012 Building Decree as requiring electricity supplies to comply with NEN 1010, the Dutch standard for low-voltage installations; it also discussed charging points for electric vehicles.[19] The 2008 handbook reported that many countries had adopted NFPA 70 without adopting the NFPA fire pump standard, NFPA 20.[20]
Structure and main articles
The NEC is divided into chapters, articles and sections, followed by annexes such as Annex D. Chapter 4, "Equipment for General Use", covers flexible cords, which the code does not accept as a wiring method or as a substitute for fixed wiring.[21] Chapter 5 contains the special requirements for hazardous (classified) locations.[22] Annex D gives worked examples of branch-circuit and feeder calculations, and fine print notes (FPNs) add guidance, for example on ground-fault protection at lower currents.[23][10] The table lists articles that the handbook cites in its electrical chapter.
| Article | Subject | Source |
|---|---|---|
| 220 | Unit lighting loads and load calculation | [23] |
| 230 | Service entrance conductors and service disconnecting means | [1] |
| 240 | Overcurrent protection, including fixture wires, cords and taps | [22] |
| 250 | Grounding of electrical installations | [24] |
| 400 | Flexible cords: types, ampacities and intended use | [21] |
| 410 and 430 | Luminaires and motors | [25] |
| 424 | Fixed electric space heating, including duct heaters | [21] |
| 500 and 505 | Hazardous (classified) locations: class and division method; zone method | [18] |
| 511, 513–517 | Garages, aircraft hangars, motor fuel dispensing, bulk storage, spray application, health care | [26] |
| 620 | Elevators, escalators, dumbwaiters and lifts | [27] |
| 700, 701, 702 | Emergency, legally required standby and optional standby systems | [28] |
| 725, 760, 800 | Signalling, fire alarm and communications circuits | [29] |
Fire safety provisions
The core of the code is the matching of conductors and overcurrent protection. Ampacity tables give the maximum current each conductor may carry, and Article 240 requires overcurrent devices to be rated or set accordingly.[22] Article 250 requires the system and the exposed metal parts to be grounded, so that a fault current finds a low-impedance path and operates the fuse or breaker quickly.[24] Wiring installed in this way opens the circuit before the current overheats the conductor or its insulation, although devices can fail and partial ground faults can heat wiring without tripping it.[30]
Protection against shock and arcing is added in specific places. Under the 2005 edition, 125 V receptacles of 15 A and 20 A in dwellings generally need ground-fault circuit interrupters in bathrooms, garages, outdoors, unfinished basements, crawl spaces and boathouses. The same applies at kitchen countertops and within 1.8 m (6 ft) of a wet-bar sink, subject to the edition's stated exceptions.[11] Arc-fault circuit interrupters detect the low, erratic currents of arcing faults that ordinary breakers miss, and the handbook notes that their requirements were being updated at the time of writing.[31]
The NEC also limits sources of ignition directly. In clothes closets, open, partially enclosed or pendant incandescent lampholders are not permitted.[32] Oil-insulated transformers with a total rating above 75 kVA must be placed in a fire-resistant vault.[33]
Low flame spread is a frequent requirement for electric cables. For signalling and communication wiring, the NEC sets rules for ducts, plenums and other air spaces because of the hazard of spreading products of combustion. Penetrations of fire-rated walls and floors must be sealed around the cables.[29] Fire alarm cables are marked by their use, for example NPLFP for non-power-limited cable in air-handling spaces, NPLFR for risers and NPLF for general use.[29] For electrical and optical fibre cables in general, the code defines four levels of performance.[34]
| Listing | Test | Exposure | Pass criterion |
|---|---|---|---|
| Dwellings and raceways | UL 1581 VW-1 (vertical wire) | Single cable, vertical | Resistant to flame spread |
| General purpose | UL 1581 vertical cable tray | 20 kW burner, grouped cables | Fire does not reach the top of a 2.4 m tray |
| Riser (shaft or floor to floor) | UL 1666 | 154.5 kW burner, grouped cables, two-storey rig | Prevents the carrying of fire from floor to floor |
| Plenum (ducts, air-handling spaces) | NFPA 262 (Steiner tunnel) | 88 kW burner, horizontal | Flame travel ≤ 1.52 m; peak optical density ≤ 0.5; average ≤ 0.15 |
The code also governs the power supplies of life safety systems. The NEC recognises emergency systems and standby systems, the latter divided into legally required and optional standby systems, in Articles 700, 701 and 702.[28] It accepts five sources for emergency and standby power: storage batteries, generator sets, uninterruptible power supplies, a separate service and unit equipment. NFPA 101 does not accept the separate service as an emergency source for the occupancies it covers.[35] A prime mover for emergency service must start automatically and reach full speed and power within 10 seconds, with on-site fuel for at least 2 hours at full output.[36] For fire pumps the NEC yields: NFPA 20 overrides its general electrical safety provisions so that the pump keeps running during a fire.[20]
In hazardous locations, flammable gases, vapours, dusts or fibres make special equipment and wiring methods necessary to prevent ignition. Article 500 divides such locations into three classes by the kind of material and two divisions by the likelihood of the hazard, a system of hazardous area classification.[18] For flammable gases, the NEC sets group designations and NFPA 497 gives the maximum experimental safe gap and minimum igniting current ratio values; NFPA 499 addresses combustible dusts.[37] In Class I, Division 1 locations, motors, luminaires, most switches and circuit breakers must be explosionproof or purged, or intrinsically safe circuits may be used.[38] The code defines explosionproof equipment as apparatus in a case that withstands an internal explosion of a specified gas, prevents ignition of the surrounding atmosphere and runs cool enough not to ignite it.[18]
Load calculation and worked example
The NEC provides methods for calculating the expected branch-circuit and feeder loads and the number of branch circuits required. Article 220 gives minimum unit lighting loads in volt-amperes (VA) per unit of floor area, and the computed feeder load is then subject to demand factors. These factors are not applied where all the lighting is likely to be used at once.[23] For loads expected to run for at least 3 hours, such as store or office lighting, the 2005 NEC calculation increases the specified load by 25 %.[23] The procedure can be written in three steps:
| Symbol | Description | Unit |
|---|---|---|
| General lighting load | VA | |
| Unit lighting load per floor area (3 VA/ft² = 32.3 VA/m² for dwellings) | VA/m² | |
| Floor area, excluding open porches, garages and unused spaces | m² | |
| Portion of the load to which demand factor applies | VA | |
| Demand factor (handbook Table 8.13.15, from the 2005 NEC) | – | |
| Net computed load | VA | |
| System voltage | V | |
| Feeder or service current | A |
For dwelling units the demand factors are 100 % on the first 3000 VA, 35 % from 3001 to 120,000 VA and 25 % on the remainder. Hospitals, hotels and warehouses have their own factors; warehouses, for example, count the first 12,500 VA in full and the remainder at 50 %. The hospital and hotel factors do not apply to areas such as operating rooms, ballrooms or dining rooms.[23]
Worked example. The handbook presents an example from the NEC for a single-family dwelling of 1500 ft² (139 m²) with a 12 kW range and a 5 kW clothes dryer.[23] The general lighting load is 1500 ft² × 3 VA/ft² = 4500 VA, or 37.5 A at 120 V, which needs three 15 A or two 20 A circuits. Two 20 A small-appliance circuits and one laundry circuit add 1500 VA each, giving 9000 VA.[23] The first 3000 VA counts in full and the remaining 6000 VA at 35 %, or 2100 VA, so the net load is 5100 VA. The example counts the range at 8000 VA and the dryer at 5000 VA, giving 18,100 VA.[39]
On a 120/240 V system the feeder current is 18,100 VA ÷ 240 V ≈ 75.4 A, which the handbook rounds to 75 A. Because the net load exceeds 10 kVA, the service conductors must be rated at 100 A.[39] The demand factors thus cut the 9000 VA of lighting and small-appliance load to 5100 VA, a reduction of about 43 %.
Effect on fire losses and limits
U.S. fire statistics are consistent with this view. In 1999–2002, electrical distribution and lighting equipment caused an estimated 32,400 U.S. home fires a year, 9 % of the total, with 220 civilian deaths. The category ranked no higher than fourth for any measure of loss except property damage, where it ranked second.[5] The handbook chapter on one- and two-family dwellings states that the widespread and long-term use of NFPA 70 has reduced electrical fires to a lower-order problem. Such fires usually involve some failure to observe the code.[40]
The handbook states that nearly all fires involving electrically powered equipment stem from foreseeable or avoidable human error.[41] One benchmark study found that 61 % of home electrical fires involved code violations, particularly of the general workmanship provisions.[5] Failure to follow the NEC or the manufacturer's instructions can lead to overloading, damaged equipment or excessive heating of nearby combustibles. Mismatched wire sizes and oversized fuses are typical examples.[41] Even correct installations deteriorate with age, which is why the handbook calls for periodic inspection and maintenance of electrical equipment.[41]
The code also has deliberate limits. For fire alarms, it does not decide which devices and systems a building needs.[4] Its general protection philosophy is set aside for fire pumps, where NFPA 20 treats the equipment as sacrificial.[20] Because jurisdictions adopt particular editions and may apply them throughout the life of an alarm system, an existing installation may follow an older edition than the one currently published.[4]
See also
- Arc fault
- Arc-fault circuit interrupter
- Bonding and grounding
- Lightning protection system
- Purged and pressurised enclosure
Notes
- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 Milatovich (2008), p. 8-137.
- ↑ 2.0 2.1 Milatovich (2008), p. 8-134.
- ↑ 3.0 3.1 3.2 Cote and Grant (2008), p. 1-65.
- ↑ 4.0 4.1 4.2 4.3 4.4 Keough and Grill (2005), p. 2.
- ↑ 5.0 5.1 5.2 Hall and Cote (2008), p. 3-15.
- ↑ 6.0 6.1 6.2 Milatovich (2008), p. 8-127.
- ↑ Cote and Grant (2008), p. 1-62.
- ↑ 8.0 8.1 Cote and Grant (2008), p. 1-64.
- ↑ Cote and Grant (2008), p. 1-57.
- ↑ 10.0 10.1 Milatovich (2008), p. 8-140.
- ↑ 11.0 11.1 Milatovich (2008), p. 8-147.
- ↑ Nasby and Kovacik (2008), p. 15-114.
- ↑ National Institute of Standards and Technology (2005), p. 201.
- ↑ Iqbal and Salley (2004), p. E-1.
- ↑ Donoghue (2008), p. 10-63.
- ↑ Razza and Grill (2005c), p. 16.
- ↑ Milatovich (2008), p. 8-138.
- ↑ 18.0 18.1 18.2 18.3 Milatovich (2008), p. 8-164.
- ↑ Van der Graaf et al. (2021/2023), pp. 14, 61.
- ↑ 20.0 20.1 20.2 Nasby and Kovacik (2008), p. 15-106.
- ↑ 21.0 21.1 21.2 Milatovich (2008), p. 8-153.
- ↑ 22.0 22.1 22.2 Milatovich (2008), p. 8-145.
- ↑ 23.0 23.1 23.2 23.3 23.4 23.5 23.6 Milatovich (2008), p. 8-152.
- ↑ 24.0 24.1 Milatovich (2008), p. 8-142.
- ↑ Milatovich (2008), p. 8-146.
- ↑ Milatovich (2008), p. 8-172.
- ↑ Milatovich (2008), p. 8-161.
- ↑ 28.0 28.1 Chisholm (2008), p. 10-3.
- ↑ 29.0 29.1 29.2 Milatovich (2008), p. 8-163.
- ↑ McDaniel (2008), p. 20-184.
- ↑ Milatovich (2008), p. 8-148.
- ↑ Milatovich (2008), p. 8-154.
- ↑ Milatovich (2008), p. 8-159.
- ↑ 34.0 34.1 Hirschler (2008a), p. 6-45.
- ↑ Chisholm (2008), p. 10-4.
- ↑ Chisholm (2008), p. 10-6.
- ↑ Ural and Garzia (2008), p. 17-151.
- ↑ Milatovich (2008), p. 8-169.
- ↑ 39.0 39.1 Milatovich (2008), p. 8-153.
- ↑ Lathrop (2008b), p. 20-58.
- ↑ 41.0 41.1 41.2 Milatovich (2008), p. 8-135.
References
- Chisholm, D., Sr. (2008). Emergency and standby power supplies. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 10-3–10-8). National Fire Protection Association.
- Cote, A. E., & Grant, C. C. (2008). Codes and standards for the built environment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 1-51–1-71). National Fire Protection Association.
- Donoghue, E. A. (2008). Building transportation systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 10-57–10-68). National Fire Protection Association.
- Hall, J. R., Jr., & Cote, A. E. (2008). An overview of the fire problem and fire protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-3–3-30). National Fire Protection Association.
- Hirschler, M. M. (2008a). Concepts and protocols of fire testing. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-35–6-60). National Fire Protection Association.
- Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
- Keough, R. J., & Grill, R. A. (2005). Fire alarm systems (NIST NCSTAR 1-4C). National Institute of Standards and Technology.
- Lathrop, J. K. (2008b). One- and two-family dwellings. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 20-55–20-61). National Fire Protection Association.
- McDaniel, D. L. (2008). Library and museum collections. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 20-179–20-202). National Fire Protection Association.
- Milatovich, R. M. (2008). Electrical systems and appliances. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-127–8-173). National Fire Protection Association.
- Nasby, J. S., & Kovacik, J. R. (2008). Fire pump controllers and power supply arrangements for motor-driven fire pumps. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 15-105–15-145). National Fire Protection Association.
- National Institute of Standards and Technology. (2005). Final report on the collapse of the World Trade Center towers (NIST NCSTAR 1).
- Razza, J. C., & Grill, R. A. (2005c). Comparison of the 1968 and current (2003) New York City Building Code provisions (NIST NCSTAR 1-1F). National Institute of Standards and Technology.
- Ural, E. A., & Garzia, H. W. (2008). Explosion prevention and protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-141–17-165). National Fire Protection Association.
- Van der Graaf, J., Hessels, T., & Rosmuller, N. (2023). Fire safety of indoor car parks accommodating electrically powered vehicles. Nederlands Instituut Publieke Veiligheid. (Original work published 2021)