Skip to content
From Fire Safety Academy Wiki
Peter (talk | contribs)
New FSE wiki article: Chlorine (written by Claude Opus 5.5)
 
Peter (talk | contribs)
FSE wiki: Fact-check: clarify NFPA 704 figure edition attribution (written by Claude Opus 5.5)
Line 20: Line 20:
Chlorine is one of the gases that the handbook describes as poisonous or irritating when inhaled or contacted. Such gases can complicate fire fighting by exposing fire fighters to a toxicity hazard, and they are labelled "poison gas" for shipment.<ref name="LE-6-167">Lemoff (2008), p. 6-167.</ref> Chlorine has been used in warfare as a poison gas, and liquid chlorine can burn the skin.<ref name="LE-6-180" /> In the classification of chemical warfare agents, chlorine and phosgene are choking or pulmonary agents. In sufficient concentrations their corrosive effect on the respiratory system causes pulmonary oedema, which fills the lungs with fluid.<ref name="MG-1-113">Meacham and Galioto (2008), p. 1-113.</ref>
Chlorine is one of the gases that the handbook describes as poisonous or irritating when inhaled or contacted. Such gases can complicate fire fighting by exposing fire fighters to a toxicity hazard, and they are labelled "poison gas" for shipment.<ref name="LE-6-167">Lemoff (2008), p. 6-167.</ref> Chlorine has been used in warfare as a poison gas, and liquid chlorine can burn the skin.<ref name="LE-6-180" /> In the classification of chemical warfare agents, chlorine and phosgene are choking or pulmonary agents. In sufficient concentrations their corrosive effect on the respiratory system causes pulmonary oedema, which fills the lungs with fluid.<ref name="MG-1-113">Meacham and Galioto (2008), p. 1-113.</ref>


NFPA 55 defines toxic and highly toxic gases by their median lethal concentration, the [[LC50]], measured on rats over one hour. A toxic gas has an LC50 of more than 200 ppm but not more than 2,000 ppm, and a highly toxic gas 200 ppm or less.<ref name="LE-6-167" /> The handbook places chlorine in the toxic class.<ref name="LE-6-180" /> The NFPA 704 marking shown for chlorine in the handbook has a health rating of 4, the highest, with zero for flammability and instability and "OX" in the special field.<ref name="LE-6-180" /> In the 2007 edition of NFPA 704, a health rating of 4 means a material that can be lethal under emergency conditions.<ref name="CW-13-123">C. J. Wright (2008a), p. 13-123.</ref>
NFPA 55 defines toxic and highly toxic gases by their median lethal concentration, the [[LC50]], measured on rats over one hour. A toxic gas has an LC50 of more than 200 ppm but not more than 2,000 ppm, and a highly toxic gas 200 ppm or less.<ref name="LE-6-167" /> The handbook places chlorine in the toxic class.<ref name="LE-6-180" /> The NFPA 704 marking shown for chlorine in the handbook has a health rating of 4, the highest, with zero for flammability and instability and "OX" in the special field.<ref name="LE-6-180" /> In the NFPA 704 scale reproduced by Wright (2008a), a health rating of 4 means a material that can be lethal under emergency conditions.<ref name="CW-13-123">C. J. Wright (2008a), p. 13-123.</ref>


Chlorine is a sensory irritant. In the SFPE Handbook, Purser describes the mouse respiratory rate test, which measures the RD50, the concentration that halves the breathing rate. Chemicals that are highly irritant in humans, such as acrolein and chlorine, have low RD50 values in mice.<ref name="PU-2-113">Purser (2002), p. 2-113.</ref> ''Introduction to Fire Safety Engineering'' describes such an [[irritant gas]] as often acidic, typically a halogen compound of chlorine, fluorine or bromine. These gases irritate the eyes and airways and so hinder vision and breathing during escape.<ref name="VR-7.7">Van Rossum (2027), §7.7.</ref> In NUREG-1805, a table of halon decomposition products gives 50 ppm by volume as a dangerous concentration of chlorine in air.<ref name="IS-B-73">Iqbal and Salley (2004), p. B-73.</ref>
Chlorine is a sensory irritant. In the SFPE Handbook, Purser describes the mouse respiratory rate test, which measures the RD50, the concentration that halves the breathing rate. Chemicals that are highly irritant in humans, such as acrolein and chlorine, have low RD50 values in mice.<ref name="PU-2-113">Purser (2002), p. 2-113.</ref> ''Introduction to Fire Safety Engineering'' describes such an [[irritant gas]] as often acidic, typically a halogen compound of chlorine, fluorine or bromine. These gases irritate the eyes and airways and so hinder vision and breathing during escape.<ref name="VR-7.7">Van Rossum (2027), §7.7.</ref> In NUREG-1805, a table of halon decomposition products gives 50 ppm by volume as a dangerous concentration of chlorine in air.<ref name="IS-B-73">Iqbal and Salley (2004), p. B-73.</ref>
Line 71: Line 71:
The sources contain some inconsistencies. The mass of a one-ton container is given as both 1,016 kg and 907 kg. The wastewater chapter prints the lower cylinder size of 150 lb as "23 kg", although 150 lb equals 68.0 kg.<ref name="LE-6-180" /><ref name="WH-9-147" /> The gases chapter names "hypochlorous and hypochloric acids" in one place and hydrochloric acid in another as products of chlorine and water.<ref name="LE-6-180" /><ref name="LE-6-176" />
The sources contain some inconsistencies. The mass of a one-ton container is given as both 1,016 kg and 907 kg. The wastewater chapter prints the lower cylinder size of 150 lb as "23 kg", although 150 lb equals 68.0 kg.<ref name="LE-6-180" /><ref name="WH-9-147" /> The gases chapter names "hypochlorous and hypochloric acids" in one place and hydrochloric acid in another as products of chlorine and water.<ref name="LE-6-180" /><ref name="LE-6-176" />


The requirements and distances in this article come from United States documents as described in the 2008 handbook. They are NFPA 55 (2005 edition), the 2007 edition of NFPA 704, the DOT hazard classes and the 2004 ''Emergency Response Guidebook''.<ref name="LR-7-39" /><ref name="CW-13-123" /><ref name="CW-13-136" /> The release statistics come from a national United States study and may differ regionally.<ref name="CW-13-121" />
The requirements and distances in this article come from United States documents as described in the 2008 handbook. They are NFPA 55 (2005 edition), NFPA 704 marking scales reproduced in the handbook, the DOT hazard classes and the 2004 ''Emergency Response Guidebook''.<ref name="LR-7-39" /><ref name="CW-13-123" /><ref name="CW-13-136" /> The release statistics come from a national United States study and may differ regionally.<ref name="CW-13-121" />


== See also ==
== See also ==

Revision as of 04:14, 8 November 2026

Chlorine is a chemical element that, at normal temperatures, is a heavy, greenish-yellow, highly toxic gas with a sharp odour.[1][2] It is shipped and stored as a liquefied gas under pressure. The NFPA Fire Protection Handbook classifies it as reactive, nonflammable, liquefied, toxic and industrial.[2] Chlorine does not burn, but it is a strong oxidiser that reacts corrosively, and sometimes explosively, with many organic materials, fuel gases and finely divided metals.[2] Its main uses are chemical processing, bleaching, the purification of drinking water and swimming pools, and the disinfection of industrial and sewage wastes.[2]

When it is released, chlorine presents mainly toxicity and corrosion hazards. The gas is about two and a half times heavier than air and hugs the ground.[2] In a United States study of hazardous material releases cited in the handbook, chlorine accounted for 3.5 percent of releases but 9.6 percent of the associated deaths and injuries, the highest share in the table.[3] For a large spill, the 2004 Emergency Response Guidebook advises protecting people downwind for up to 6.76 km (4.2 mi) at night.[4]

Properties

Chlorine belongs to the halogens, together with fluorine, bromine and iodine. These elements are chemically active, and their activity decreases in that order, so chlorine is less reactive than fluorine but more reactive than bromine.[1] The normal boiling point of chlorine is about −34.4 °C (−30 °F). At 0 °C (32 °F) the liquid has a density of 1,469 kg/m³ (91.7 lb/ft³) and the gas a density of 3.20 kg/m³ (0.2 lb/ft³). The latent heat of vaporisation at the boiling point is 287.7 kJ/kg (123.7 Btu/lb).[2] One cubic metre of liquid produces about 458 m³ of gas at 0 °C.[2]

Like all liquefied gases, liquid chlorine is stored above its normal boiling point and stays under pressure only as long as the container remains closed.[5] The handbook notes that chlorine gas liquefies fairly easily, so a process designed for gaseous chlorine can become difficult to control if liquid forms.[6] Most noncryogenic liquefied gases evaporate so fast on release that they do not form a pool. Chlorine and butane, with their lower vapour pressures, are exceptions and can form a liquid pool.[7]

Chlorine is one of the few common gases that can be seen and smelled. The handbook names it as an example of a coloured gas and of a gas with a strong odour, both of which help people notice a leak.[8] Its sharp odour serves as a warning.[2] In contact with water, chlorine forms acids that are corrosive to most metals.[2][7]

Uses

Chlorine is used mainly in chemical processing, bleaching, the purification of drinking water and swimming pools, and the sanitation of industrial and sewage wastes.[2] It is also given off in some manufacturing processes and by bleaching powder, especially in the presence of strong acids.[1] Mixing strong oxidising agents with hydrochloric acid releases chlorine gas, and so does a mixture of nitric and hydrochloric acids.[1] Calcium hypochlorite releases chlorine freely when it meets acids or moisture.[9]

In a wastewater treatment plant, disinfection destroys pathogenic bacteria, viruses and amoebic cysts. Chemical disinfection with chlorine is the most widely used method, and the chlorine is generally delivered as a gas or a liquid.[10] Smaller plants use cylinders holding from 68 kg (150 lb) up to 907 kg (1 ton). Larger plants may take chlorine in bulk from a tank truck or a railroad tank car.[10] Many plants also dechlorinate the effluent, usually with sulfur dioxide or activated carbon, to protect aquatic life from residual chlorine.[10] Chlorine is used in sludge stabilisation as well.[11]

The handbook's table of gases commonly found in wastewater plants lists chlorine as nonflammable and heavier than air. It names disinfection processes and storage tanks as its sources and marks it as a gas that accelerates combustion.[12] The same chapter notes that specialty gases such as chlorine can create flammable or explosive conditions, alone or when mixed with other chemicals.[13]

Toxicity

Chlorine is one of the gases that the handbook describes as poisonous or irritating when inhaled or contacted. Such gases can complicate fire fighting by exposing fire fighters to a toxicity hazard, and they are labelled "poison gas" for shipment.[14] Chlorine has been used in warfare as a poison gas, and liquid chlorine can burn the skin.[2] In the classification of chemical warfare agents, chlorine and phosgene are choking or pulmonary agents. In sufficient concentrations their corrosive effect on the respiratory system causes pulmonary oedema, which fills the lungs with fluid.[15]

NFPA 55 defines toxic and highly toxic gases by their median lethal concentration, the LC50, measured on rats over one hour. A toxic gas has an LC50 of more than 200 ppm but not more than 2,000 ppm, and a highly toxic gas 200 ppm or less.[14] The handbook places chlorine in the toxic class.[2] The NFPA 704 marking shown for chlorine in the handbook has a health rating of 4, the highest, with zero for flammability and instability and "OX" in the special field.[2] In the NFPA 704 scale reproduced by Wright (2008a), a health rating of 4 means a material that can be lethal under emergency conditions.[16]

Chlorine is a sensory irritant. In the SFPE Handbook, Purser describes the mouse respiratory rate test, which measures the RD50, the concentration that halves the breathing rate. Chemicals that are highly irritant in humans, such as acrolein and chlorine, have low RD50 values in mice.[17] Introduction to Fire Safety Engineering describes such an irritant gas as often acidic, typically a halogen compound of chlorine, fluorine or bromine. These gases irritate the eyes and airways and so hinder vision and breathing during escape.[18] In NUREG-1805, a table of halon decomposition products gives 50 ppm by volume as a dangerous concentration of chlorine in air.[19]

Exposure assessment at an incident uses several limits. The handbook lists the immediately dangerous to life or health value (IDLH), the LC50, the lethal dose (LD50), the permissible exposure limit and three threshold limit values.[20] The Occupational Safety and Health Administration defines an IDLH atmosphere as one that poses an immediate hazard to life or causes immediate irreversible debilitating effects on health.[21] The sources consulted give no numerical IDLH, LC50 or exposure limit for chlorine.

Oxidiser and reactivity hazards

Although chlorine is nonflammable, it is a strong oxidiser. It can react corrosively, and in some cases explosively, with acetylene, turpentine, ether, gaseous ammonia, hydrocarbons, most fuel gases and finely divided metals.[2] Davenport adds that turpentine, phosphorus and finely divided metals ignite spontaneously in the presence of the halogens.[1] Combustion does not always need oxygen. Drysdale notes that hydrocarbons may "burn" in an atmosphere of chlorine.[22] NUREG-1805 adds that a flame can be sustained in pure chlorine, although the combustion cannot be complete.[23]

Metals can burn in chlorine as well. Mild steel ignites and burns in chlorine at 251 °C (484 °F).[1] Thin sections of steel and copper, such as the fins of heat transfer tubes, can ignite easily in hot chlorine.[24] In the chapter on oxygen-enriched atmospheres, chlorine is named among the other oxidants that may result in enhanced combustion.[25] The "OX" in the special field of the NFPA 704 marking identifies an oxidiser.[16]

Its reactivity also governs the choice of materials. Below 110 °C (230 °F), steel, copper, iron and lead are widely used for containers, piping and equipment.[2] Above about that temperature, steel is attacked rapidly, and leaks can develop when a container is exposed to fire.[2] With water, chlorine forms acids; the gases chapter names hydrochloric acid as the product.[7] The main practical problem is that the container metal reacts with the acid, which enlarges the leak.[7]

Containers, storage and transport

Chlorine is shipped in DOT and Transport Canada cylinders, in DOT-specification portable tanks known as "one-ton containers" and in insulated railroad tank cars.[2] The handbook gives the mass of a one-ton container as 1,016 kg in the gases chapter and as 907 kg in the storage and wastewater chapters.[2][8][10] A compressed gas cylinder or a ton container of chlorine is protected against overpressure by fusible plugs, and tank cars by pressure-relief valves.[2] Because the operation of a fusible plug depressurises the container completely, the probability of a BLEVE is low.[2]

Portable liquefied gas containers are normally stored upright, so that the relief device stays in contact with the vapour space. The relieving capacity of such devices is determined for vapour discharge and is severely restricted if liquid is discharged. One-ton chlorine containers are an exception to this rule.[8]

In the United States, NFPA 55 (2005 edition), as reproduced by Lemoff and Rivkin (2008), sets maximum allowable quantities per control area for liquefied toxic gases. The limit is 68 kg (150 lb) in an unsprinklered area without a gas cabinet, gas room or exhausted enclosure. It rises to 136 kg (300 lb) with either sprinklers or such an enclosure, and to 272 kg (600 lb) with both.[26] A single 907 kg container is thus about 13 times the smallest of these limits. NFPA 55 also requires toxic gases to be kept 6.1 m (20 ft) from pyrophoric, oxidising and flammable gases, unless a suitable barrier separates them.[27]

Chlorine is a major rail commodity in the United States. In 2005 it ranked twelfth among hazardous materials in rail transport, with 36,475 shipments in Division 2.3.[28] Chlorine travels in insulated railroad tank cars, and the handbook shows the fittings of a liquid chlorine tank car grouped inside a protective housing.[2][29] Division 2.3 covers toxic gases. Without adequate human data, a gas is presumed toxic when its LC50 in laboratory animals is no more than 5,000 ppm.[30]

Hazardous materials placarding identifies chlorine in transport. Placards of 274 mm (10.8 in.) are required on some bulk packages, and labels of 102 mm (4 in.) or smaller are used on cylinders. They convey information by colour, symbol, hazard class or division number, and wording or a four-digit identification number.[31] The number for chlorine is UN 1017.[2] A square white background behind a Division 2.3 placard indicates special handling.[31] NFPA 704 markings, by contrast, are used within facilities and not on transport vehicles.[16]

Behaviour on release and emergency response

A chlorine release is mainly a "no fire" emergency, in which a toxic gas threatens people without burning.[32] Its spread is governed by the density of the gas. Because the gas is about two and a half times heavier than air, it stays close to the ground.[2] Liquid chlorine can form a pool rather than flash off completely.[7] Liquefied gases escaping as liquid can also form a visible cloud of condensed water vapour.[8] A gas detection system for chlorine usually relies on electrochemical cells, the predominant sensing method for this gas, and portable chlorine monitors use the same principle.[33][34]

Worked example: gas volume from a one-ton container

The handbook's physical data show why even one container can affect a large area. A container holding 907 kg (1 ton) of liquid chlorine contains 907 / 1,469 = 0.617 m³ of liquid. At 0 °C this produces 907 / 3.20 = 283 m³ of gas, which agrees with the expansion factor of 458.[2][10] To dilute this gas to the dangerous concentration of 50 ppm listed in NUREG-1805 would take 283 / 0.000050 = 5.7 million m³ of air.[19] That is roughly the air over 1.1 km² of ground to a height of 5 m.

This simple balance ignores wind, terrain and the uneven mixing of a real cloud, so it is only an order-of-magnitude illustration. For actual incidents, the handbook refers responders to the table of initial isolation and protective action distances in the Emergency Response Guidebook, to planning documents or to dispersion modelling. Wind speed, wind direction and topography must be considered.[20]

The 2004 guidebook values for chlorine (UN 1017) illustrate the scale. For a small spill, it advises isolating 30.5 m (100 ft) in all directions and protecting persons downwind for 0.32 km (0.2 mi) by day and 1.13 km (0.7 mi) by night. For a large spill, the values are 274 m (900 ft), 2.74 km (1.7 mi) and 6.76 km (4.2 mi).[4] The night distances are about two and a half to three and a half times the day distances.

Emergency response

The handbook's guidance for chlorine emergencies starts with water spray, which can control the gas. Fire fighters using hose streams should wear full protective clothing. Water should not be applied to liquid chlorine, because it speeds up evaporation.[2] Water should also not be applied directly to a leak, because acid corrosion may enlarge it.[2]

When a fire exposes a chlorine container, water should be applied to cool it, both against leaks from attacked steel and as protection against a BLEVE.[2] Chlorine and fluorine are not fire hazards in themselves, but toxic gas releases should be expected when their cylinders are involved in a fire. A self-contained breathing apparatus (SCBA) is mandatory in such fires.[35] In the United States, OSHA regulations and NFPA standards allow only positive-pressure SCBA in atmospheres that are, or may become, IDLH.[36]

The chlorine industry in the United States has set up a leak-control programme. It places trained emergency personnel at strategic locations and provides special kits for stopping the more common leaks in cylinders, ton containers and tank cars.[2] Train derailments in South Carolina and Texas in 2004 and 2005 spilled chlorine. The handbook notes that the fire departments along these railways lacked full hazardous materials response training to NFPA 472.[37] Accidental releases of common chemicals such as chlorine near buildings are also considered in planning for extreme events.[38]

Chlorine in fires and fire toxicity

Chlorine also appears as a product of fires. Fuels that contain chlorine, such as polyvinyl chloride (PVC), produce hydrogen chloride (HCl) and chlorine gas (Cl2) when they burn.[39] Most of the chlorine in PVC, however, is released as hydrogen chloride.[40] The CFAST zone model follows the same approach and assumes that all of the chlorine in the fuel is converted to HCl.[41]

For fire toxicity this means that chlorine in burning materials mainly matters through the irritant acid gases it forms. Van Rossum treats such irritant gases separately from the toxic gases assessed by fractional effective dose, because they act on the eyes and airways and hinder escape.[18] Chlorine itself is listed among the decomposition products of halon extinguishing agents. NUREG-1805 gives it a dangerous concentration of 50 ppm in that context.[19]

Limitations and misconceptions

It would be wrong to treat chlorine as harmless in a fire because it is nonflammable. As a strong oxidiser, it can cause fires or explosions with fuel gases, hydrocarbons, ammonia and powdered metals, and steel can burn in it at 251 °C.[2][1] Water also needs care. Spray controls the gas and cools exposed containers, but water on a leak or on liquid chlorine makes matters worse.[2]

The sources contain some inconsistencies. The mass of a one-ton container is given as both 1,016 kg and 907 kg. The wastewater chapter prints the lower cylinder size of 150 lb as "23 kg", although 150 lb equals 68.0 kg.[2][10] The gases chapter names "hypochlorous and hypochloric acids" in one place and hydrochloric acid in another as products of chlorine and water.[2][7]

The requirements and distances in this article come from United States documents as described in the 2008 handbook. They are NFPA 55 (2005 edition), NFPA 704 marking scales reproduced in the handbook, the DOT hazard classes and the 2004 Emergency Response Guidebook.[26][16][4] The release statistics come from a national United States study and may differ regionally.[3]

See also

Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Davenport (2008), p. 7-52.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25 2.26 2.27 2.28 2.29 2.30 2.31 Lemoff (2008), p. 6-180.
  3. ↑ 3.0 3.1 Industrial Economics, Inc., as cited in C. J. Wright (2008a), p. 13-121.
  4. ↑ 4.0 4.1 4.2 2004 Emergency Response Guidebook, as cited in C. J. Wright (2008a), p. 13-136.
  5. ↑ Lemoff (2008), p. 6-170.
  6. ↑ Schwab (2008a), p. 8-25.
  7. ↑ 7.0 7.1 7.2 7.3 7.4 7.5 Lemoff (2008), p. 6-176.
  8. ↑ 8.0 8.1 8.2 8.3 Lemoff and Rivkin (2008), p. 7-40.
  9. ↑ Davenport (2008), p. 7-47.
  10. ↑ 10.0 10.1 10.2 10.3 10.4 10.5 Wheeler (2008), p. 9-147.
  11. ↑ Wheeler (2008), p. 9-151.
  12. ↑ Wheeler (2008), p. 9-150.
  13. ↑ Wheeler (2008), p. 9-149.
  14. ↑ 14.0 14.1 Lemoff (2008), p. 6-167.
  15. ↑ Meacham and Galioto (2008), p. 1-113.
  16. ↑ 16.0 16.1 16.2 16.3 C. J. Wright (2008a), p. 13-123.
  17. ↑ Purser (2002), p. 2-113.
  18. ↑ 18.0 18.1 Van Rossum (2027), §7.7.
  19. ↑ 19.0 19.1 19.2 Iqbal and Salley (2004), p. B-73.
  20. ↑ 20.0 20.1 C. J. Wright (2008a), p. 13-134.
  21. ↑ Loflin (2008), p. 12-110.
  22. ↑ Drysdale (2008), p. 2-17.
  23. ↑ Iqbal and Salley (2004), p. 3-9.
  24. ↑ Schwab (2008a), p. 8-24.
  25. ↑ Rosales and Stoltzfus (2008), p. 9-227.
  26. ↑ 26.0 26.1 Lemoff and Rivkin (2008), p. 7-39.
  27. ↑ Lemoff and Rivkin (2008), p. 7-38.
  28. ↑ C. J. Wright (2008b), p. 21-113.
  29. ↑ C. J. Wright (2008b), p. 21-130.
  30. ↑ C. J. Wright (2008a), p. 13-120.
  31. ↑ 31.0 31.1 C. J. Wright (2008a), p. 13-124.
  32. ↑ Lemoff (2008), p. 6-175.
  33. ↑ Cholin (2008a), p. 14-104.
  34. ↑ Cholin (2008a), p. 14-111.
  35. ↑ Davenport (2008), p. 7-53.
  36. ↑ Teele (2008), p. 12-151.
  37. ↑ Laughlin (2008), p. 12-168.
  38. ↑ Meacham and Galioto (2008), p. 1-128.
  39. ↑ Custer and Milke (2008), p. 2-77.
  40. ↑ Benedetti and Colonna (2008), p. 6-222.
  41. ↑ Peacock et al. (2026), p. 12.

References

  • Benedetti, R. P., & Colonna, G. R. (2008). Polymeric materials. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-209–6-231). National Fire Protection Association.
  • Cholin, J. M. (2008a). Gas and vapor detection systems and monitors. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-99–14-112). National Fire Protection Association.
  • Custer, R. L. P., & Milke, J. A. (2008). Fundamentals of fire detection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-75–2-78). National Fire Protection Association.
  • Davenport, J. A. (2008). Storage and handling of chemicals. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-43–7-55). National Fire Protection Association.
  • Drysdale, D. (2008). Physics and chemistry of fire. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-3–2-20). National Fire Protection Association.
  • Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
  • Laughlin, J. W. (2008). Training programs for fire and emergency service personnel. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-161–12-175). National Fire Protection Association.
  • Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
  • Lemoff, T. C., & Rivkin, C. H. (2008). Storage of gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-35–7-42). National Fire Protection Association.
  • Loflin, M. E. (2008). Safety, medical, and health issues and programs. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-107–12-125). National Fire Protection Association.
  • Meacham, B. J., & Galioto, C. (2008). Protecting against extreme events. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 1-109–1-136). National Fire Protection Association.
  • Peacock, R. D., McGrattan, K. B., Forney, G. P., & Reneke, P. A. (2026). CFAST – Consolidated Fire and Smoke Transport: Vol. 1. Technical reference guide (Version 7, NIST Technical Note 1889v1). National Institute of Standards and Technology. https://doi.org/10.6028/NIST.TN.1889v1
  • Purser, D. A. (2002). Toxicity assessment of combustion products. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-83–2-171). National Fire Protection Association; Society of Fire Protection Engineers.
  • Rosales, K., & Stoltzfus, J. M. (2008). Oxygen-Enriched atmospheres. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-225–9-243). National Fire Protection Association.
  • Schwab, R. F. (2008a). Chemical processing equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-17–8-29). National Fire Protection Association.
  • Teele, B. W. (2008). Fire and emergency services protective clothing and protective equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-143–12-160). National Fire Protection Association.
  • Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
  • Wheeler, J. F. (2008). Protection of wastewater treatment plants. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-141–9-155). National Fire Protection Association.
  • Wright, C. J. (2008a). Managing the response to hazardous material incidents. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-117–13-144). National Fire Protection Association.
  • Wright, C. J. (2008b). Rail transportation systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-109–21-134). National Fire Protection Association.