FSE wiki: Fact-check: clarify radiant thresholds, injury endpoint, FED steps and window scope (written by Claude Opus 5.5) |
Add 5 watermarked NFPA SVG illustrations |
||
| Line 18: | Line 18: | ||
== Degrees of burn and survival == | == Degrees of burn and survival == | ||
First-degree burns affect only the outer layer of the skin and show abnormal redness, pain and sometimes a little fluid under that layer.<ref name="GB-6-26" /> Second-degree burns penetrate more deeply; the area is moist and pink and the skin blisters. Third-degree burns are usually dry, charred or pearly white.<ref name="GB-6-26" /> Beyler stresses that severity is a continuous range, from a burn that barely damages the skin to destruction of all skin layers and the tissue below.<ref name="Bey-3-308">Beyler (2002a), pp. 3-308–3-309.</ref> Other scales exist. Purser describes a scale of six degrees, in which fourth-degree burns need skin grafts and the fifth and sixth degrees destroy muscle and bone. A simpler scheme separates partial-thickness burns, which heal, from full-thickness burns, which need grafts.<ref name="Pur-2-128" /> | First-degree burns affect only the outer layer of the skin and show abnormal redness, pain and sometimes a little fluid under that layer.<ref name="GB-6-26" /> Second-degree burns penetrate more deeply; the area is moist and pink and the skin blisters. Third-degree burns are usually dry, charred or pearly white.<ref name="GB-6-26" /> Beyler stresses that severity is a continuous range, from a burn that barely damages the skin to destruction of all skin layers and the tissue below.<ref name="Bey-3-308">Beyler (2002a), pp. 3-308–3-309.</ref> Other scales exist. Purser describes a scale of six degrees, in which fourth-degree burns need skin grafts and the fifth and sixth degrees destroy muscle and bone. A simpler scheme separates partial-thickness burns, which heal, from full-thickness burns, which need grafts.<ref name="Pur-2-128" /> | ||
[[File:fse-burn-injury-v1.svg|thumb|upright=1.5|alt=Cross-section of skin with epidermis and dermis; three brackets show the depth reached by first-, second- and third-degree burns.|Depth of first-, second- and third-degree burns in the two main layers of the skin, with the skin temperatures for pain and blistering. Based on Beyler (2002a), pp. 3-308–3-309 and Gann and Bryner (2008), p. 6-26.]] | |||
The area burned matters as much as the depth. Beyler (2002a) reported that healthy adults and teenagers could normally be expected to survive if less than 20 % of the body surface had second- and third-degree burns. With more than 50 % covered by full-thickness burns, survivors were unlikely even with intensive care.<ref name="Bey-3-309" /> Purser (2002) reported survivals with burns of up to 80 % of the body surface, but low chances at 35 % or more. He gave young adults about a 50 % chance of surviving a burn of half the body surface, and elderly people the same chance for a burn covering 20 %.<ref name="Pur-2-128" /> Mortality is higher under 1 year and over 40 years of age, and [[smoke inhalation]] raises it further.<ref name="Nolan-F11" /> | The area burned matters as much as the depth. Beyler (2002a) reported that healthy adults and teenagers could normally be expected to survive if less than 20 % of the body surface had second- and third-degree burns. With more than 50 % covered by full-thickness burns, survivors were unlikely even with intensive care.<ref name="Bey-3-309" /> Purser (2002) reported survivals with burns of up to 80 % of the body surface, but low chances at 35 % or more. He gave young adults about a 50 % chance of surviving a burn of half the body surface, and elderly people the same chance for a burn covering 20 %.<ref name="Pur-2-128" /> Mortality is higher under 1 year and over 40 years of age, and [[smoke inhalation]] raises it further.<ref name="Nolan-F11" /> | ||
| Line 31: | Line 32: | ||
The first equation gives seconds and the second minutes, both with the flux in kW/m².<ref name="Bey-3-309" /><ref name="GB-6-26" /> Purser expresses the same effects as a radiant dose, the flux to the power 4/3 multiplied by time. Pain occurs at about 1.33 to 1.67 (kW/m²)<sup>4/3</sup>·min, second-degree burns at 4 to 12.2 and third-degree burns at about 16.7 (kW/m²)<sup>4/3</sup>·min.<ref name="Pur-2-129" /> | The first equation gives seconds and the second minutes, both with the flux in kW/m².<ref name="Bey-3-309" /><ref name="GB-6-26" /> Purser expresses the same effects as a radiant dose, the flux to the power 4/3 multiplied by time. Pain occurs at about 1.33 to 1.67 (kW/m²)<sup>4/3</sup>·min, second-degree burns at 4 to 12.2 and third-degree burns at about 16.7 (kW/m²)<sup>4/3</sup>·min.<ref name="Pur-2-129" /> | ||
[[File:fse-burn-injury-v2.svg|thumb|upright=1.5|alt=Log-log chart of time against radiant heat flux: curves for time to pain and time to a second-degree burn, with threshold lines at 1.7 and 2.5 kW/m².|Time to pain and to a second-degree burn on bare skin as a function of radiant heat flux. Based on Beyler (2002a), p. 3-309, Gann and Bryner (2008), p. 6-26 and Purser (2002), p. 2-129.]] | |||
For convected heat, the heating rate depends on the air temperature, air movement, humidity and clothing.<ref name="Pur-2-127">Purser (2002), p. 2-127.</ref> Tolerance data for unprotected skin suggest a limit of about 120 °C (248 °F), above which pain comes quickly and burns follow within a few minutes.<ref name="GB-6-26" /> Below it, a longer exposure can still cause hyperthermia. For air with less than 10 % water vapour, Purser gives the time to incapacitation in minutes as a function of the gas temperature:<ref name="Pur-2-129" /> | For convected heat, the heating rate depends on the air temperature, air movement, humidity and clothing.<ref name="Pur-2-127">Purser (2002), p. 2-127.</ref> Tolerance data for unprotected skin suggest a limit of about 120 °C (248 °F), above which pain comes quickly and burns follow within a few minutes.<ref name="GB-6-26" /> Below it, a longer exposure can still cause hyperthermia. For air with less than 10 % water vapour, Purser gives the time to incapacitation in minutes as a function of the gas temperature:<ref name="Pur-2-129" /> | ||
| Line 37: | Line 39: | ||
The handbook prints a similar equation, <math>t_\mathrm{I,conv} = 4.1 \times 10^{8}\, T^{-3.61}</math>, for the time to thermal collapse, with <math>T</math> described as the temperature at the skin surface.<ref name="GB-6-26" /> Moisture makes hot air much more harmful, because humid air transfers heat more efficiently and blocks cooling by sweat.<ref name="GB-6-26" /> Air saturated with water vapour can be breathed only up to about 60 °C, and steam at 100 °C destroyed the epidermis of dogs within a few seconds.<ref name="Pur-2-127" /> | The handbook prints a similar equation, <math>t_\mathrm{I,conv} = 4.1 \times 10^{8}\, T^{-3.61}</math>, for the time to thermal collapse, with <math>T</math> described as the temperature at the skin surface.<ref name="GB-6-26" /> Moisture makes hot air much more harmful, because humid air transfers heat more efficiently and blocks cooling by sweat.<ref name="GB-6-26" /> Air saturated with water vapour can be breathed only up to about 60 °C, and steam at 100 °C destroyed the epidermis of dogs within a few seconds.<ref name="Pur-2-127" /> | ||
[[File:fse-burn-injury-v3.svg|thumb|upright=1.5|alt=Chart of tolerance time against air temperature from 60 to 200 °C: two falling curves and five table points between them.|Time to incapacitation by convected heat in air with less than 10 % water vapour: two correlations and Purser's table values. Based on Purser (2002), p. 2-129 and Gann and Bryner (2008), p. 6-26.]] | |||
Contact with hot solids is a third route. Metal at 60 °C causes pain after 1 s and a burn after 10 s; at 80 °C, pain comes after 100 ms and a burn after 1 s.<ref name="Pur-2-126" /> What counts is the temperature at the contact surface. For skin at 35 °C touching bodies at 100 °C, it is 98 °C for mild steel, 82 °C for glass, 65 °C for wood and 46 °C for cork.<ref name="Pur-2-126" /> Purser therefore treats conducted heat as important in fires mainly where skin touches hot surfaces such as door handles.<ref name="Pur-2-129" /> | Contact with hot solids is a third route. Metal at 60 °C causes pain after 1 s and a burn after 10 s; at 80 °C, pain comes after 100 ms and a burn after 1 s.<ref name="Pur-2-126" /> What counts is the temperature at the contact surface. For skin at 35 °C touching bodies at 100 °C, it is 98 °C for mild steel, 82 °C for glass, 65 °C for wood and 46 °C for cork.<ref name="Pur-2-126" /> Purser therefore treats conducted heat as important in fires mainly where skin touches hot surfaces such as door handles.<ref name="Pur-2-129" /> | ||
| Line 101: | Line 104: | ||
The FED therefore reaches the design limit of 0.3 between the 75 s and 80 s calculation points. It is 0.273 at 75 s and 0.351 at 80 s; linear interpolation gives about 76.7 s. The last completed 5 s step below the limit is at 75 s. Here the radiant term brings the occupant to the limit. In Purser's example of a single armchair burning in a room, convected heat dominated instead. Incapacitation by skin pain and burns was predicted in the fourth minute, at an air temperature of 220 °C.<ref name="Pur-2-130">Purser (2002), p. 2-130.</ref> | The FED therefore reaches the design limit of 0.3 between the 75 s and 80 s calculation points. It is 0.273 at 75 s and 0.351 at 80 s; linear interpolation gives about 76.7 s. The last completed 5 s step below the limit is at 75 s. Here the radiant term brings the occupant to the limit. In Purser's example of a single armchair burning in a room, convected heat dominated instead. Incapacitation by skin pain and burns was predicted in the fourth minute, at an air temperature of 220 °C.<ref name="Pur-2-130">Purser (2002), p. 2-130.</ref> | ||
[[File:fse-burn-injury-v4.svg|thumb|upright=1.5|alt=Heat FED rises over two minutes; the radiant share carries it above 0.3 between 75 and 80 s.|Build-up of the fractional effective dose of heat in the worked example, split into convective and radiant parts. Based on Ministry of Business, Innovation and Employment (2013), p. 47 and Purser (2002), p. 2-129.]] | |||
== Burns in fire and injury statistics == | == Burns in fire and injury statistics == | ||
| Line 117: | Line 121: | ||
Protective clothing is tested against predicted skin burns. The Thermal Protective Performance (TPP) test exposes a fabric to a combined convective and radiant flux of 84 kW/m² (7.4 Btu/ft²·s), simulating a flash fire.<ref name="SC-6-93">Stull and Chines (2008), p. 6-93.</ref> A copper calorimeter behind the fabric measures the heat passing through, and its temperature rise is compared with human skin tolerance data. This predicts the time to pain and to a second-degree burn. In the manikin test of ASTM F1930, a clothed manikin with more than 100 sensors is exposed to propane flames for 3 to 12 seconds. The sensors show where second- and third-degree burns would occur.<ref name="SC-6-93" /> | Protective clothing is tested against predicted skin burns. The Thermal Protective Performance (TPP) test exposes a fabric to a combined convective and radiant flux of 84 kW/m² (7.4 Btu/ft²·s), simulating a flash fire.<ref name="SC-6-93">Stull and Chines (2008), p. 6-93.</ref> A copper calorimeter behind the fabric measures the heat passing through, and its temperature rise is compared with human skin tolerance data. This predicts the time to pain and to a second-degree burn. In the manikin test of ASTM F1930, a clothed manikin with more than 100 sensors is exposed to propane flames for 3 to 12 seconds. The sensors show where second- and third-degree burns would occur.<ref name="SC-6-93" /> | ||
[[File:fse-burn-injury-v5.svg|thumb|upright=1.5|alt=Schematic of the TPP test: burners and quartz tubes below a horizontal fabric specimen, with a copper calorimeter on top.|Principle of the Thermal Protective Performance (TPP) test: a fabric is exposed to 84 kW/m² and a copper calorimeter measures the heat that passes through it. Based on Stull and Chines (2008), p. 6-93.]] | |||
For workers exposed to flash fires, early studies found that the main injuries came from clothing that kept burning, not from the flash fire itself.<ref name="SC-6-87" /> For structural firefighters, Veghte estimated tolerance times of 10 to 20 minutes in routine conditions, 3 to 5 minutes in ordinary conditions and 10 to 30 seconds in emergencies.<ref name="SC-6-87" /> Skin begins to burn at about 57 °C (135 °F) after a short exposure, so bare skin is not a practical heat sensor.<ref name="Tee-12-147">Teele (2008), p. 12-147.</ref> The Fire Department of New York required protective trousers as well as coats from 1995 and hoods from 1996. Its recorded burn injuries fell from 1,832 in 1993 to 442 in 2005, a drop of 76 %.<ref name="Tee-12-148">Teele (2008), p. 12-148.</ref> | For workers exposed to flash fires, early studies found that the main injuries came from clothing that kept burning, not from the flash fire itself.<ref name="SC-6-87" /> For structural firefighters, Veghte estimated tolerance times of 10 to 20 minutes in routine conditions, 3 to 5 minutes in ordinary conditions and 10 to 30 seconds in emergencies.<ref name="SC-6-87" /> Skin begins to burn at about 57 °C (135 °F) after a short exposure, so bare skin is not a practical heat sensor.<ref name="Tee-12-147">Teele (2008), p. 12-147.</ref> The Fire Department of New York required protective trousers as well as coats from 1995 and hoods from 1996. Its recorded burn injuries fell from 1,832 in 1993 to 442 in 2005, a drop of 76 %.<ref name="Tee-12-148">Teele (2008), p. 12-148.</ref> | ||
Revision as of 08:19, 8 November 2026
A burn injury is damage to the skin and the tissues below it caused by hot liquids, flames, radiant heat, contact with hot solids, caustic chemicals, electricity or nuclear radiation.[1] In fires, burns of the skin are one of three ways in which heat harms people, next to hyperthermia (heat stroke) and burns of the respiratory tract.[2] Burns are graded by depth, as first, second or third degree, and by the share of the body surface they cover.[3]
Fire safety engineers turn the onset of pain and burns into tenability limits for escape routes. The 2008 handbook describes fluxes below about 2.5 kW/m² as tolerable for 30 minutes or longer.[2] Burns are also common outside fires. In the United States, hot tap water, drinks, food, fats or cooking oil caused 67 % of the deaths due to hot objects in 1999–2002.[4] Clothing changes the risk strongly, through garments that ignite and through protective clothing that insulates the wearer.[5]
How heat damages skin
The heat released by a burning material has a convective part, carried by hot gases, and a radiative part, each measured as a heat flux in kW/m².[2] The body removes heat by sweating and by the circulation of blood, and these defences must be overcome before the skin temperature rises. Up to a critical exposure, excess heat can be tolerated, but above it the tolerance decreases exponentially.[2] The wider subject, including heat stroke, is treated in Effects of heat on people.
According to measurements by Buettner, pain starts when the skin temperature at a depth of 0.1 mm reaches 44.8 °C.[6] Pain is soon followed by burns, which can cause incapacitation, severe injury or death. The effect is essentially the same whether the heat arrives by conduction from a hot body, by convection from hot air or by radiation. A skin temperature of 43 °C causes pain and some damage to cells, while 60 °C coagulates the proteins of the tissue.[6]
The skin has two main layers: the outer epidermis, 0.05 to 0.1 mm thick, and the inner dermis, 1 to 2 mm thick.[7] The simplest model treats skin and the tissue below it as a solid with constant properties, heated by conduction only. Under a constant heat flux, its surface temperature rises in proportion to the flux and to the square root of time:[7]
Here is the skin surface temperature, the initial temperature and the thermal inertia of the skin.[7] By this equation, doubling the flux cuts the time to a given temperature rise to a quarter. Measured pain times deviate somewhat from it, which Beyler attributes to a slightly higher skin temperature at pain onset under higher fluxes.[7]
Mehta and co-workers found that the severity of a burn depends on the energy absorbed after the skin surface has reached 55 °C.[7] An absorbed energy of 41.8 kJ/m² gives pain or a mild second-degree burn, and a further 83.6 kJ/m² gives a blister or severe second-degree burn. More than 162.2 kJ/m² produces severe third-degree burns with permanent tissue damage.[7] A glossary entry quoted in NUREG-1805 gives slightly different skin temperatures: about 48 °C for a first-degree burn, 55 °C for a second-degree burn and 72 °C for instantaneous destruction of the skin.[1]
Degrees of burn and survival
First-degree burns affect only the outer layer of the skin and show abnormal redness, pain and sometimes a little fluid under that layer.[2] Second-degree burns penetrate more deeply; the area is moist and pink and the skin blisters. Third-degree burns are usually dry, charred or pearly white.[2] Beyler stresses that severity is a continuous range, from a burn that barely damages the skin to destruction of all skin layers and the tissue below.[8] Other scales exist. Purser describes a scale of six degrees, in which fourth-degree burns need skin grafts and the fifth and sixth degrees destroy muscle and bone. A simpler scheme separates partial-thickness burns, which heal, from full-thickness burns, which need grafts.[3]
The area burned matters as much as the depth. Beyler (2002a) reported that healthy adults and teenagers could normally be expected to survive if less than 20 % of the body surface had second- and third-degree burns. With more than 50 % covered by full-thickness burns, survivors were unlikely even with intensive care.[7] Purser (2002) reported survivals with burns of up to 80 % of the body surface, but low chances at 35 % or more. He gave young adults about a 50 % chance of surviving a burn of half the body surface, and elderly people the same chance for a burn covering 20 %.[3] Mortality is higher under 1 year and over 40 years of age, and smoke inhalation raises it further.[1]
Burns harm the whole body. Fluid lost into the burn can cause circulatory failure, a fall in blood pressure and loss of consciousness.[3] Victims who survive this shock may die within weeks from effects on the brain, heart, lungs, liver and kidneys; fluid in the lungs (pulmonary oedema) is the most common cause.[3] The glossary in NUREG-1805 names infection as the most common cause of death after extensive burns.[1] It adds that burns of up to 15 % of the body surface are usually treated in emergency rooms, and burns of more than 25 % in specialised burn centres.[1]
Thresholds and correlations
For radiant heat there is a threshold flux below which significant heating of the skin is prevented. The 2008 Fire Protection Handbook describes fluxes below about 2.5 kW/m² as tolerable for 30 minutes or longer; above that approximate threshold, time to burning falls quickly.[2] Purser (2002) says fluxes below 2.5 kW/m² can be tolerated for more than 5 minutes, but his table gives only 30 seconds at exactly 2.5 kW/m².[9] Beyler reports that no pain was observed below 1.7 kW/m², whatever the exposure time. For comparison, the solar flux on a clear summer day is about 1 kW/m².[7]
Above the threshold, two correlations are widely quoted. Beyler gives the time to pain from Buettner's tests, in which volunteers exposed their forearms to thermal radiation.[7] The handbook gives the time to a second-degree burn under radiant flux:[2]
The first equation gives seconds and the second minutes, both with the flux in kW/m².[7][2] Purser expresses the same effects as a radiant dose, the flux to the power 4/3 multiplied by time. Pain occurs at about 1.33 to 1.67 (kW/m²)4/3·min, second-degree burns at 4 to 12.2 and third-degree burns at about 16.7 (kW/m²)4/3·min.[9]
For convected heat, the heating rate depends on the air temperature, air movement, humidity and clothing.[10] Tolerance data for unprotected skin suggest a limit of about 120 °C (248 °F), above which pain comes quickly and burns follow within a few minutes.[2] Below it, a longer exposure can still cause hyperthermia. For air with less than 10 % water vapour, Purser gives the time to incapacitation in minutes as a function of the gas temperature:[9]
The handbook prints a similar equation, , for the time to thermal collapse, with described as the temperature at the skin surface.[2] Moisture makes hot air much more harmful, because humid air transfers heat more efficiently and blocks cooling by sweat.[2] Air saturated with water vapour can be breathed only up to about 60 °C, and steam at 100 °C destroyed the epidermis of dogs within a few seconds.[10]
Contact with hot solids is a third route. Metal at 60 °C causes pain after 1 s and a burn after 10 s; at 80 °C, pain comes after 100 ms and a burn after 1 s.[6] What counts is the temperature at the contact surface. For skin at 35 °C touching bodies at 100 °C, it is 98 °C for mild steel, 82 °C for glass, 65 °C for wood and 46 °C for cork.[6] Purser therefore treats conducted heat as important in fires mainly where skin touches hot surfaces such as door handles.[9]
| Mode of heat transfer | Exposure | Tolerance time |
|---|---|---|
| Radiation | below 2.5 kW/m² | more than 5 min |
| Radiation | 2.5 kW/m² | 30 s |
| Radiation | 10 kW/m² | 4 s |
| Convection | below 60 °C, air saturated with water vapour | more than 30 min |
| Convection | 100 °C, less than 10 % water vapour | 12 min |
| Convection | 120 °C, less than 10 % water vapour | 7 min |
| Convection | 140 °C, less than 10 % water vapour | 4 min |
| Convection | 160 °C, less than 10 % water vapour | 2 min |
| Convection | 180 °C, less than 10 % water vapour | 1 min |
When conditions change during an escape, the heat dose is added up over time, as for toxic gases. This fractional effective dose (FED) sums the fractions of the incapacitating dose received in each time step. Incapacitation is expected when the sum reaches 1.[9]
| Symbol | Description | Unit |
|---|---|---|
| time to pain on bare skin | s | |
| time to a second-degree burn (incapacitation) by radiant heat | min | |
| time to incapacitation by convected heat | min | |
| incident radiant heat flux | kW/m² | |
| gas temperature (skin surface temperature in the handbook equation) | °C | |
| , | skin surface temperature and initial skin temperature | °C |
| thermal inertia of the skin (conductivity × density × specific heat) | W²·s/(m⁴·K²) | |
| exposure time | s | |
| time step of the dose calculation | min | |
| FED | fractional effective dose of heat | – |
Worked examples
The first example compares the correlations for bare skin at 5 kW/m². This is the acceptable level for people in the United States Federal Safety Standards for Liquefied Natural Gas Facilities (49 CFR Part 193, 1980), as described by Beyler (2002a).[11] The pain correlation gives s.[7] The handbook correlation gives min, or 33.6 s, for a second-degree burn.[2]
Purser's dose values give pain after 9.4 to 11.7 s and a second-degree burn after 28 to 85 s, since 5 to the power 4/3 is 8.55.[9] Beyler states that at this flux unbearable pain occurs after about 13 s and second-degree burns may occur after about 40 s.[11] The shortest calculated times are about 9 s to pain and 28 s to a second-degree burn; the latter does not establish when blisters form.[7]
The second example uses the dose method described in the 2013 commentary on the first edition of the New Zealand Verification Method C/VM2. It combines Purser's convective equation with the handbook equation for radiant heat.[12] An occupant walks for 2 minutes along a route where conditions worsen every 30 s; the calculation uses 5 s dose steps. The four conditions are 60 °C with 1.0 kW/m², 80 °C with 2.0 kW/m², 100 °C with 3.0 kW/m² and 120 °C with 4.0 kW/m².
The radiant term is left out below 2.5 kW/m², which the commentary describes as tolerable for 30 minutes or more.[12] The first minute adds only 0.041. At 100 °C, min and min, so the third 30 s condition adds 0.063 for convection and 0.40 for radiation.
The FED therefore reaches the design limit of 0.3 between the 75 s and 80 s calculation points. It is 0.273 at 75 s and 0.351 at 80 s; linear interpolation gives about 76.7 s. The last completed 5 s step below the limit is at 75 s. Here the radiant term brings the occupant to the limit. In Purser's example of a single armchair burning in a room, convected heat dominated instead. Incapacitation by skin pain and burns was predicted in the fourth minute, at an air temperature of 220 °C.[13]
Burns in fire and injury statistics
The Fire Protection Handbook lists burns from fire, hot surfaces, steam or other hot objects among the types of harm to people in the built environment.[14] United States in-home surveys estimated about 2,130,000 burn injuries a year in 1980–1981 and 1,129,000 a year in 1991–1993, a fall from 1.0 to 0.4 per 100 people.[4] The samples were small, so the estimates carry considerable uncertainty.
Most deaths from hot objects involve hot liquids or steam. In 1999–2002, 67 % involved hot tap water, drinks, food, fats or cooking oil, and 22 % involved steam or other hot liquids or vapours.[4] Such deaths numbered between 97 and 130 a year from 1993 to 2002.[15] For hot liquids and vapours, the very young and older adults are the high-risk age groups, with much higher risks for older adults.[4] In South African townships, an NFPA project of 2005 identified spilled hot liquids, tipped paraffin stoves and clothing set alight by open flames as common causes of burns to young children.[16]
Clothing fires are a classic source of fatal burns that fire statistics can miss. United States death certificates record fewer than 200 clothing-ignition deaths a year.[17] In 1983–1985, clothing-ignition burns caused about one fire death in 20 overall, but one in eight among people aged 65 and over. This gave older people five times the population rate of death from burns in clothing fires.[18] These numbers belong to the wider pattern described in High-risk populations.
Inside burning buildings, incapacitation and death are much more often caused by toxic gases than by direct burns.[19] Burns still dominate some events. Secondary dust deflagrations often occur in occupied parts of a building and cause severe burns to the occupants.[20] In the World Trade Center evacuation of 2001, a survivor from floor 88 of WTC 1 had burns over 77 % of her body. She reported that crowds in the stairwell parted to let her through.[21] In fire investigations, the location and severity of burns in hospital or autopsy reports help to reconstruct the fire.[22]
Clothing and protective clothing
Garments can cause burns as well as prevent them, a central topic of textile flammability. A nylon or polyester undergarment beneath a burning outer garment may not ignite, yet it may shrink, stick to the skin and cause injury.[23] Shrinkage onto the skin removes the insulating layer of air and greatly increases the heat reaching the skin. Fabrics that weaken by charring may split apart and expose the skin directly.[24] On an instrumented mannequin, pile fabrics such as terry cloth and cotton flannel gave much higher burn injury estimates than almost 60 other apparel fabrics.[25]
A United States standard for children's sleepwear in sizes 0 to 6x was issued in 1971 and extended to sizes 7 to 14 three years later.[18] Since then, burn deaths of children under 15 from ignition of any clothing have dropped to five or fewer a year. The history and tests are described in Children's sleepwear flammability.
Protective clothing is tested against predicted skin burns. The Thermal Protective Performance (TPP) test exposes a fabric to a combined convective and radiant flux of 84 kW/m² (7.4 Btu/ft²·s), simulating a flash fire.[26] A copper calorimeter behind the fabric measures the heat passing through, and its temperature rise is compared with human skin tolerance data. This predicts the time to pain and to a second-degree burn. In the manikin test of ASTM F1930, a clothed manikin with more than 100 sensors is exposed to propane flames for 3 to 12 seconds. The sensors show where second- and third-degree burns would occur.[26]
For workers exposed to flash fires, early studies found that the main injuries came from clothing that kept burning, not from the flash fire itself.[5] For structural firefighters, Veghte estimated tolerance times of 10 to 20 minutes in routine conditions, 3 to 5 minutes in ordinary conditions and 10 to 30 seconds in emergencies.[5] Skin begins to burn at about 57 °C (135 °F) after a short exposure, so bare skin is not a practical heat sensor.[27] The Fire Department of New York required protective trousers as well as coats from 1995 and hoods from 1996. Its recorded burn injuries fell from 1,832 in 1993 to 442 in 2005, a drop of 76 %.[28]
Use in design and regulation
Burn criteria enter fire engineering mainly as tenability limits when available and required escape times are compared. The International Fire Engineering Guidelines (2005) list a limiting radiation that would cause skin burns as one possible acceptance criterion.[29] They refer to a guide of the Society of Fire Protection Engineers (SFPE) from 2000 that predicts the onset of pain and first- and second-degree burns.[29]
In New Zealand, the 2013 commentary on the first edition of Verification Method C/VM2 limits the heat FED of an escaping occupant to 0.3.[12] The second edition (2025) requires the thermal FED to be calculated with the procedures of ISO 13571, including radiative and convective effects.[30] For its single-window method, occupants passing a window or glazed panel in an exitway or on an external escape route must not be exposed to radiation that causes pain. The time to pain, from the same equation as above, must exceed the exposure time, and the method caps the radiation at 10 kW/m²; multiple windows need a more detailed analysis.[31]
For hazard zones around large hydrocarbon fires, Beyler (2002a) treats the 5 kW/m² level of 49 CFR Part 193 (1980) as a criterion for injury. He derives a fatality threshold of about 10 kW/m² for a 40 s exposure from analyses of nuclear weapon casualties.[11] In the Netherlands, fire safety engineering practice mostly uses 2.5 kW/m² for escape and 1 kW/m² for prolonged stay.[32] For non-enclosed spaces used for escape, the explanatory notes to the Dutch building decree (Bbl) take at most 2 kW/m² below the smoke layer.[32]
A hot smoke layer of about 200 °C overhead corresponds roughly to the 2.5 kW/m² limit.[9] Introduction to Fire Safety Engineering obtains this with a view factor of 1, an emissivity of 1 and a receiving temperature of 37 °C. The exact result is 2.3 kW/m², which the book deliberately rounds up.[32] For hot gases, it gives about 80 °C as bearable for a short escape and about 60 °C for more than ten minutes at high humidity.[32] The handbook reports that fire tests by the National Research Council of Canada took 149 °C (300 °F) as the maximum survivable temperature of breathing air.[2]
Limits and uncertainty
The correlations rest on tests with volunteers and on animal tests with pigs and dogs.[7][10] For fatal exposures they rest on analyses of nuclear weapon casualties, whose interpretation is somewhat subjective because the exposures were very short.[11] They describe bare skin. Clothing gives some protection above 120 °C, but at lower temperatures it can shorten tolerance by hindering cooling by sweat.[33] At 120 °C, Purser's equation gives 4.3 min, his table 7 min and the handbook equation 12.8 min, a spread of a factor of three.[9][2]
People also differ in their response. The handbook treats this as a statistical distribution, in which about 11.4 % of people would still be incapacitated at an FED of 0.3.[34] No criterion is low enough to be safe for everyone. Survival after a burn also depends on medical treatment, which the engineering models leave out.[3]
Two misconceptions are common. The first is that hot air alone burns the lungs. Thermal burns of the respiratory tract from air with less than 10 % water vapour do not occur without burns to the skin or face.[2] Limits that protect the skin should therefore also protect the airways, except for steam and humid smoke at about 100 °C.[9][3] The second is that firefighters should "feel the heat" through thinner clothing. The handbook rejects this, because every part of the body is sensitive to heat and skin burns at relatively low temperatures.[27]
See also
- Fire-based emergency medical services
- Structural firefighting protective clothing
- Tenability criteria
- Fractional effective dose
Notes
- ↑ 1.0 1.1 1.2 1.3 1.4 Nolan (2000), as cited in Iqbal and Salley (2004), p. F-11.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 Gann and Bryner (2008), p. 6-26.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 Purser (2002), p. 2-128.
- ↑ 4.0 4.1 4.2 4.3 Hall and Twomey (2008), pp. 1-8–1-9.
- ↑ 5.0 5.1 5.2 Stull and Chines (2008), p. 6-87.
- ↑ 6.0 6.1 6.2 6.3 Purser (2002), p. 2-126.
- ↑ 7.00 7.01 7.02 7.03 7.04 7.05 7.06 7.07 7.08 7.09 7.10 7.11 7.12 Beyler (2002a), p. 3-309.
- ↑ Beyler (2002a), pp. 3-308–3-309.
- ↑ 9.00 9.01 9.02 9.03 9.04 9.05 9.06 9.07 9.08 9.09 Purser (2002), p. 2-129.
- ↑ 10.0 10.1 10.2 Purser (2002), p. 2-127.
- ↑ 11.0 11.1 11.2 11.3 Beyler (2002a), p. 3-310.
- ↑ 12.0 12.1 12.2 Ministry of Business, Innovation and Employment (2013), p. 47.
- ↑ Purser (2002), p. 2-130.
- ↑ Hall and Twomey (2008), p. 1-6.
- ↑ Hall and Twomey (2008), p. 1-9.
- ↑ Grant and Eksteen (2008), p. 5-26.
- ↑ Hall and Twomey (2008), p. 1-7.
- ↑ 18.0 18.1 Stull and Chines (2008), p. 6-86.
- ↑ Babrauskas (2008b), p. 6-124.
- ↑ Cholin (2008d), p. 9-21.
- ↑ Kugler (2002), as cited in Fahy and Proulx (2005), p. 20.
- ↑ Custer et al. (2008), p. 3-115.
- ↑ Stull and Chines (2008), p. 6-83.
- ↑ Stull and Chines (2008), p. 6-84.
- ↑ Stull and Chines (2008), p. 6-89.
- ↑ 26.0 26.1 Stull and Chines (2008), p. 6-93.
- ↑ 27.0 27.1 Teele (2008), p. 12-147.
- ↑ Teele (2008), p. 12-148.
- ↑ 29.0 29.1 National Research Council of Canada et al. (2005), p. 2.2-2.
- ↑ Ministry of Business, Innovation and Employment (2025b), p. 17.
- ↑ Ministry of Business, Innovation and Employment (2025b), pp. 34–35.
- ↑ 32.0 32.1 32.2 32.3 Van Rossum (2027), §7.7.
- ↑ Purser (2002), p. 2-125.
- ↑ Gann and Bryner (2008), p. 6-25.
References
- Babrauskas, V. (2008b). Upholstered furniture and mattresses. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-103–6-128). National Fire Protection Association.
- Beyler, C. L. (2002a). Fire hazard calculations for large, open hydrocarbon fires. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-268–3-314). National Fire Protection Association; Society of Fire Protection Engineers.
- Cholin, J. M. (2008d). Woodworking facilities and processes. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-3–9-25). National Fire Protection Association.
- Custer, R. L. P., Sheppard, D. T., & Wood, C. B. (2008). Applying models to fire protection engineering problems and fire investigations. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-111–3-120). National Fire Protection Association.
- Fahy, R. F., & Proulx, G. (2005). Analysis of published accounts of the World Trade Center evacuation (NIST NCSTAR 1-7A). National Institute of Standards and Technology.
- Gann, R. G., & Bryner, N. P. (2008). Combustion products and their effects on life safety. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-11–6-34). National Fire Protection Association.
- Grant, E., & Eksteen, R. (2008). Fire and life safety education messages. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 5-21–5-27). National Fire Protection Association.
- Hall, J. R., Jr., & Twomey, E. R. (2008). Challenges to safety in the built environment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 1-3–1-29). National Fire Protection Association.
- Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
- Ministry of Business, Innovation and Employment. (2013). Commentary for Building Code clauses C1–C6 and Verification Method C/VM2.
- Ministry of Business, Innovation and Employment. (2025b). Verification Method C/VM2: Framework for fire safety design (2nd ed.).
- National Research Council of Canada, International Code Council, Department of Building and Housing, & Australian Building Codes Board. (2005). International fire engineering guidelines (2005 ed.). Australian Building Codes Board.
- Purser, D. A. (2002). Toxicity assessment of combustion products. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-83–2-171). National Fire Protection Association; Society of Fire Protection Engineers.
- Stull, J. O., & Chines, S. A. (2008). Fibers and textiles. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-75–6-102). National Fire Protection Association.
- Teele, B. W. (2008). Fire and emergency services protective clothing and protective equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-143–12-160). National Fire Protection Association.
- Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.