Skip to content
From Fire Safety Academy Wiki
Daan (talk | contribs)
Refine sentence flow and printed-page reference locators (written by GPT-6)
Mark (talk | contribs)
Add SVG figures fse-friction-loss-v1.svg, fse-friction-loss-v2.svg, fse-friction-loss-v3.svg (list-5 visual plan)
Line 5: Line 5:
== Distributed and local losses ==
== Distributed and local losses ==
[[Hydraulic calculation]] separates friction from the other terms in the energy balance; [[Turbulence|turbulence]] and interaction with the pipe wall contribute to distributed resistance. Bends, entries, valves and section changes add local losses. Calling these local contributions minor losses describes their modelling category, not a guarantee that their combined effect is small. <ref name="T_4-49_4-56" />
[[Hydraulic calculation]] separates friction from the other terms in the energy balance; [[Turbulence|turbulence]] and interaction with the pipe wall contribute to distributed resistance. Bends, entries, valves and section changes add local losses. Calling these local contributions minor losses describes their modelling category, not a guarantee that their combined effect is small. <ref name="T_4-49_4-56" />
[[File:fse-friction-loss-v1.svg|thumb|upright=1.5|alt=Friction loss: functional relationships. Measurement and water paths are distinct.|Friction loss: functional relationships. Schematic explanation; dimensions are not installation instructions.]]


The [[Hazen-Williams formula]] and [[Darcy-Weisbach equation]] provide different means of representing distributed loss; their input quantities and limitations need to remain visible. A [[Fire hose|fire hose]] also forms part of a delivery route whose resistance reduces the pressure available at the nozzle. A pressure suitable at the supply connection is therefore not necessarily the pressure delivered after the complete hose and pipe route. <ref name="T_4-50_4-56">Titus (2002), ch. 4-2, pp. 4-50–4-56.</ref><ref name="H_16_10_16-195">Cote (2008), ch. 16.10, pp. 16-195.</ref>
The [[Hazen-Williams formula]] and [[Darcy-Weisbach equation]] provide different means of representing distributed loss; their input quantities and limitations need to remain visible. A [[Fire hose|fire hose]] also forms part of a delivery route whose resistance reduces the pressure available at the nozzle. A pressure suitable at the supply connection is therefore not necessarily the pressure delivered after the complete hose and pipe route. <ref name="T_4-50_4-56">Titus (2002), ch. 4-2, pp. 4-50–4-56.</ref><ref name="H_16_10_16-195">Cote (2008), ch. 16.10, pp. 16-195.</ref>
Line 12: Line 13:
== Pipe resistance and internal condition ==
== Pipe resistance and internal condition ==
Moving water loses mechanical energy through interaction with pipe walls and through changes in direction or section; turbulent mixing contributes to this dissipation. The resistance depends on the actual internal bore and its condition, not simply the name printed on the pipe. Valves, elbows, entries and other fittings introduce additional local losses. <ref name="T_4-49_4-56" />
Moving water loses mechanical energy through interaction with pipe walls and through changes in direction or section; turbulent mixing contributes to this dissipation. The resistance depends on the actual internal bore and its condition, not simply the name printed on the pipe. Valves, elbows, entries and other fittings introduce additional local losses. <ref name="T_4-49_4-56" />
[[File:fse-friction-loss-v2.svg|thumb|upright=1.5|alt=Distributed and local resistance. Measurement and water paths are distinct.|Distributed and local resistance. Schematic explanation; dimensions are not installation instructions.]]


The Darcy-Weisbach equation expresses distributed loss through a dimensionless friction factor; that factor depends on the flow regime and, for turbulent flow, on relative roughness. The Hazen-Williams formula instead uses an empirical coefficient for water service. These methods describe related hydraulic behaviour, but their coefficients do not have interchangeable meanings. <ref name="T_4-50_4-53">Titus (2002), ch. 4-2, pp. 4-50–4-53.</ref>
The Darcy-Weisbach equation expresses distributed loss through a dimensionless friction factor; that factor depends on the flow regime and, for turbulent flow, on relative roughness. The Hazen-Williams formula instead uses an empirical coefficient for water service. These methods describe related hydraulic behaviour, but their coefficients do not have interchangeable meanings. <ref name="T_4-50_4-53">Titus (2002), ch. 4-2, pp. 4-50–4-53.</ref>
Line 25: Line 27:
== Applying the Darcy-Weisbach relation ==
== Applying the Darcy-Weisbach relation ==
The Darcy-Weisbach relation describes distributed pipe loss using mean velocity and a friction factor; the factor represents the effect of the flow regime and pipe condition. Reynolds number connects velocity and diameter with the fluid's kinematic viscosity. Relative roughness compares the wall's characteristic roughness with the internal diameter. <ref name="T_4-49_4-52">Titus (2002), ch. 4-2, pp. 4-49–4-52.</ref>
The Darcy-Weisbach relation describes distributed pipe loss using mean velocity and a friction factor; the factor represents the effect of the flow regime and pipe condition. Reynolds number connects velocity and diameter with the fluid's kinematic viscosity. Relative roughness compares the wall's characteristic roughness with the internal diameter. <ref name="T_4-49_4-52">Titus (2002), ch. 4-2, pp. 4-49–4-52.</ref>
[[File:fse-friction-loss-v3.svg|thumb|upright=1.5|alt=Selecting a friction factor. Measurement and water paths are distinct.|Selecting a friction factor. Schematic explanation; dimensions are not installation instructions.]]


The equation below gives head loss in metres of the flowing fluid; pressure loss follows by multiplying head loss by density and gravitational acceleration. The factor is the Darcy friction factor used in the cited handbook equation. Keeping its convention explicit prevents confusion with other friction-factor definitions. <ref name="T_4-50_4-52">Titus (2002), ch. 4-2, pp. 4-50–4-52.</ref>
The equation below gives head loss in metres of the flowing fluid; pressure loss follows by multiplying head loss by density and gravitational acceleration. The factor is the Darcy friction factor used in the cited handbook equation. Keeping its convention explicit prevents confusion with other friction-factor definitions. <ref name="T_4-50_4-52">Titus (2002), ch. 4-2, pp. 4-50–4-52.</ref>

Revision as of 19:41, 12 November 2026

Friction loss is the irreversible loss of fluid mechanical energy caused by resistance during flow through pipes and fittings. [1] It reduces the pressure available for useful discharge after elevation and velocity effects have been accounted for. Flow rate, internal diameter, wall condition and local geometry influence the loss. A pressure difference measured without those conditions cannot by itself identify deterioration or quantify useful outlet pressure. [2]

The underlying hydraulic assessment follows water from a defined source to its intended outlet. Elevation, velocity changes and irreversible losses must be distinguished. Observations also need the flow and network conditions under which they were obtained. A mathematically correct result can still be misleading if a source condition, connecting segment or component loss has been omitted from the description. [2][3] Static pressure and flowing pressure describe different conditions. [4]

Distributed and local losses

Hydraulic calculation separates friction from the other terms in the energy balance; turbulence and interaction with the pipe wall contribute to distributed resistance. Bends, entries, valves and section changes add local losses. Calling these local contributions minor losses describes their modelling category, not a guarantee that their combined effect is small. [1]

Friction loss: functional relationships. Measurement and water paths are distinct.
Friction loss: functional relationships. Schematic explanation; dimensions are not installation instructions.

The Hazen-Williams formula and Darcy-Weisbach equation provide different means of representing distributed loss; their input quantities and limitations need to remain visible. A fire hose also forms part of a delivery route whose resistance reduces the pressure available at the nozzle. A pressure suitable at the supply connection is therefore not necessarily the pressure delivered after the complete hose and pipe route. [5][6]

A water supply curve represents the available side of the comparison, while the distribution calculation represents the required side; each must use the same flow and pressure reference when compared. A favourable static pressure can fall substantially under discharge because resistance then becomes active. This is why both measurement conditions and the full hydraulic route matter. [3]

Pipe resistance and internal condition

Moving water loses mechanical energy through interaction with pipe walls and through changes in direction or section; turbulent mixing contributes to this dissipation. The resistance depends on the actual internal bore and its condition, not simply the name printed on the pipe. Valves, elbows, entries and other fittings introduce additional local losses. [1]

Distributed and local resistance. Measurement and water paths are distinct.
Distributed and local resistance. Schematic explanation; dimensions are not installation instructions.

The Darcy-Weisbach equation expresses distributed loss through a dimensionless friction factor; that factor depends on the flow regime and, for turbulent flow, on relative roughness. The Hazen-Williams formula instead uses an empirical coefficient for water service. These methods describe related hydraulic behaviour, but their coefficients do not have interchangeable meanings. [7]

At fixed diameter and roughness coefficient, Hazen-Williams loss increases approximately with flow raised to the power 1.85; doubling flow therefore produces considerably more than twice the loss. Increasing bore has a strong opposite effect because diameter appears with an exponent of 4.87. This explains why a short restricted connection can materially influence an otherwise generous water supply. [8][9]

Fittings can be represented by local resistance coefficients or by equivalent pipe lengths where the selected method permits; equivalent length is a calculation device, not an extra measured length on the drawing. Its use must remain consistent with the pipe and friction assumptions behind the published value. A special valve's measured pressure-loss curve may provide a better representation than a generic fitting allowance. [10][11]

Age and deposits introduce further uncertainty; corrosion can increase roughness, reduce the effective bore and release material that later obstructs a smaller passage. These mechanisms are distinct, so changing a roughness coefficient does not necessarily represent a local blockage. Inspection findings and flow measurements help determine whether the calculation still describes the installation. [12][13]

A sound comparison keeps elevation, flow and valve state consistent between observations; a high static pressure can coexist with poor flowing performance because frictional loss emerges when water moves. Conversely, a pressure difference caused by elevation does not establish pipe deterioration. The interpretation depends on the physical route and the condition under which each reading was taken. [14][4]

Applying the Darcy-Weisbach relation

The Darcy-Weisbach relation describes distributed pipe loss using mean velocity and a friction factor; the factor represents the effect of the flow regime and pipe condition. Reynolds number connects velocity and diameter with the fluid's kinematic viscosity. Relative roughness compares the wall's characteristic roughness with the internal diameter. [15]

Selecting a friction factor. Measurement and water paths are distinct.
Selecting a friction factor. Schematic explanation; dimensions are not installation instructions.

The equation below gives head loss in metres of the flowing fluid; pressure loss follows by multiplying head loss by density and gravitational acceleration. The factor is the Darcy friction factor used in the cited handbook equation. Keeping its convention explicit prevents confusion with other friction-factor definitions. [16]

hf=fLDv22g,Re=vDν

Symbol Description Unit
hf,L,D Head loss, length and internal diameter m
f,Re Darcy friction factor and Reynolds number dimensionless
v,g Mean velocity and gravitational acceleration m/s; m/s²
ν Kinematic viscosity m²/s

For laminar pipe flow below a Reynolds number of about 2,000, Titus gives the factor as 64 divided by Reynolds number; transitional flow does not have the same simple certainty. In turbulent flow, roughness and Reynolds number determine the appropriate factor through correlations or a Moody diagram. A constant factor cannot be assumed valid through every change of flow or liquid condition. [7]

Titus's comparison example uses approximately 1,893 L/min in a 102.26 mm internal bore over 30.48 m. With the stated friction factor of 0.0188, recalculation gives approximately 4.21 m of head loss. These values are converted from the example's original customary units. The result differs from its Hazen-Williams example because the selected assumptions represent resistance differently. [10]

The method still requires a defensible pipe model; deposits, local restrictions and uncertain internal diameter can dominate uncertainty even when the formula is correct. Local fitting losses are added through appropriate coefficients or compatible equivalent lengths. Elevation changes remain energy terms rather than being counted as friction. [2][17]

Applying the Hazen-Williams relation

The Hazen-Williams relation represents pipe friction through an empirical water-flow equation; Titus explains that its coefficient is fitted to flow behaviour rather than derived from a complete fluid-property model. Water temperature and the range of pipe conditions therefore matter to its interpretation. It is not a general-purpose equation for every liquid used in fire protection. [8]

The following form expresses the pressure loss through a straight length in kilopascals; it is obtained by converting Titus's bar-per-metre form and multiplying by pipe length. Flow is in litres per minute and actual internal diameter is in millimetres. Changing those units without changing the constant produces a different and incorrect calculation. [18]

Δp=6.05×107LQ1.85C1.85D4.87

Symbol Description Unit
Δp,L Frictional pressure loss and pipe length kPa; m
Q,D Water flow and actual internal diameter L/min; mm
C Empirical Hazen-Williams coefficient dimensionless

Titus compares methods using a flow of approximately 1,893 L/min through 30.48 m of pipe with a 102.26 mm internal diameter. Using a C-factor of 100 gives approximately 69.4 kPa loss by this formula. The example demonstrates the method with stated inputs; it does not prescribe that coefficient for every steel pipe. Different condition assumptions produce different predictions for the same nominal pipe. [10]

Sensitivity can be illustrated without selecting another installation. Doubling flow at fixed diameter and C-factor multiplies the calculated loss by approximately 3.61. Reducing C from 120 to 80 multiplies loss by approximately 2.12 at unchanged flow. These recalculated ratios follow directly from the exponents and help explain why condition and demand assumptions matter. Titus cautions that Hazen-Williams becomes unsuitable for coefficients appreciably below 100, particularly for very rough pipes. The C-factor comparison therefore illustrates equation sensitivity rather than validating a severely deteriorated installation. [19][20]

The formula describes distributed resistance, not every possible obstruction; a partially closed valve or a lodged object can create a concentrated restriction that needs separate representation. Corrosion may affect both roughness and bore, while internal debris can move during testing or operation. Treating all these effects as an arbitrary change to C can hide the physical defect being investigated. [12][13]

Pressure, flow and energy

Water pressure describes only one part of the energy available in a pipe; elevation contributes potential energy, while movement contributes velocity head. Titus describes these quantities using head, expressed as an equivalent height of water. A hydraulic calculation must therefore compare locations through a common energy balance, rather than subtracting unrelated gauge readings. [21]

For steady, incompressible flow, the energy balance adds pump head and subtracts irreversible losses between two sections; the following form assumes that section-average velocity adequately represents kinetic energy. It describes a defined flow path, with all elevations measured from the same datum. Sudden changes require a different, transient analysis. [22]

p1ρg+v122g+z1+Hp=p2ρg+v222g+z2+hL

Symbol Description Unit
p Pressure at the section Pa
ρ Water density kg/m³
g Gravitational acceleration m/s²
v Mean velocity m/s
z,Hp,hL Elevation, added pump head and head loss m

Pressure can decrease because water rises, because velocity increases, or because energy is dissipated; these effects have different physical meanings. An elevation change can be recovered on a descending route, whereas friction dissipates mechanical energy. A larger pipe can reduce friction but cannot remove the elevation difference between the source and the outlet. [14]

Continuity provides the corresponding flow constraint: volume flow equals cross-sectional area multiplied by mean velocity; the same flow moves faster through a smaller internal bore. At a junction, incoming and outgoing flows balance, while losses depend on the flow assigned to each connected segment. Nominal pipe size alone does not supply the internal diameter needed for this calculation. [22][23]

The pressure at a sprinkler is the pressure remaining after the complete upstream route has been considered; it is not the pressure indicated beside a remote pump or street hydrant. The route includes connecting mains, valves, elevation and distribution piping. Leaving out an inconvenient section creates an apparently favourable calculation without providing the corresponding water at the outlet. [9][24]

Comparing supply and demand

Supply and demand curves answer complementary questions; a supply curve gives the pressure available at different flows under stated conditions. A demand calculation gives the pressure needed to deliver the selected flow through the protection system. Their comparison is meaningful only at a common reference point and for compatible operating assumptions. [3]

A common water-supply approximation treats the pressure drop from the test's static value as proportional to flow raised to the power 1.85. The relation can interpolate a measured pressure-flow pair and supports the traditional transformed-axis graph. It is an empirical representation of a network, not a physical guarantee at every extrapolated flow. [4][8]

p(Q)=ps−(ps−pr)(QQt)1.85

Symbol Description Unit
ps,pr Static and test residual pressures kPa
Qt Measured test discharge L/min
Q,p(Q) Investigated flow and predicted pressure L/min; kPa

Using the pressure and flow inputs in Fleming's printed example gives a useful arithmetic check; converted to SI, they are approximately 689 kPa static and 552 kPa residual at 3,785 L/min. At 1,703 L/min, the equation gives approximately 658 kPa. This recalculation uses the stated inputs; it does not reproduce the inconsistent intermediate answer printed in that example. [4]

A pump adds a further pressure-flow relationship; the available inlet pressure combines with the differential head developed by the pump, after appropriate elevation and velocity corrections. The resulting supply is not obtained by adding the rated pump pressure at every flow. Both high-flow delivery and low-flow maximum pressure need consideration. [25][26]

The calculation must also preserve the difference between capacity and duration; a source may meet a demand point initially while exhausting a finite reserve too soon. Two paths may appear redundant while sharing one vulnerable source or connecting segment. Pressure-flow agreement is therefore one part of demonstrating the performance of the complete supply arrangement. [27][28]

Measuring the available supply

A supply test relates an observed discharge to the pressure remaining elsewhere in the connected system; the initial static reading describes the condition before the test discharge begins. The residual reading describes the pressure while the measured discharge is flowing. Both belong to the same test arrangement and must be recorded with its location and operating conditions. [4][29]

The flowing outlet and the pressure observation have different functions; a pitot measurement in an appropriate free jet supports an estimate of outlet flow. A gauge at the residual hydrant measures pressure in the distribution system during that discharge. Substituting jet pressure for residual system pressure confuses two different physical quantities. [29][4]

The discharge estimate depends on outlet geometry and the coefficient representing its losses; a disturbed or nonuniform jet makes a single point reading less representative. Probe alignment and position also influence the measurement. For some discharge devices, a calibrated nozzle or suitable flowmeter provides a more appropriate method than applying a simple pitot relation. [29]

Test results describe a network state, rather than an unlimited promise of future supply; domestic demand, pumps, source levels and closed valves can change that state. The pressure reference must also be carried correctly to the building calculation. A test performed at a different elevation or upstream of additional resistance needs hydraulic interpretation before comparison with system demand. [30][3]

A main-drain test provides a different kind of evidence; the handbook uses changes from previous static and flowing readings to identify possible deterioration or obstruction. This is useful for detecting change, but it does not independently establish the full sprinkler demand. Test opening, supply state and instrument condition affect whether successive observations are comparable. [31]

Pump testing likewise separates a start test from a flow-performance test; running successfully without substantial discharge demonstrates some operating functions but does not establish the entire pump curve. Flowing observations across the relevant operating range give evidence about delivery capability. The handbook describes retaining records so that deterioration and the ability to meet system demand can be assessed. [32]

See also

Notes

  1. ↑ 1.0 1.1 1.2 Titus (2002), ch. 4-2, pp. 4-49–4-56.
  2. ↑ 2.0 2.1 2.2 Titus (2002), ch. 4-2, pp. 4-47–4-56.
  3. ↑ 3.0 3.1 3.2 3.3 Fleming (2002), ch. 4-3, pp. 4-81–4-83.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 4.5 Fleming (2002), ch. 4-3, pp. 4-81.
  5. ↑ Titus (2002), ch. 4-2, pp. 4-50–4-56.
  6. ↑ Cote (2008), ch. 16.10, pp. 16-195.
  7. ↑ 7.0 7.1 Titus (2002), ch. 4-2, pp. 4-50–4-53.
  8. ↑ 8.0 8.1 8.2 Titus (2002), ch. 4-2, pp. 4-52–4-53.
  9. ↑ 9.0 9.1 Fleming (2002), ch. 4-3, pp. 4-75–4-81.
  10. ↑ 10.0 10.1 10.2 Titus (2002), ch. 4-2, pp. 4-56.
  11. ↑ Cote (2008), ch. 15.3, pp. 15-59.
  12. ↑ 12.0 12.1 Cote (2008), ch. 15.5, pp. 15-79–15-81.
  13. ↑ 13.0 13.1 Cote (2008), ch. 16.11, pp. 16-212.
  14. ↑ 14.0 14.1 Titus (2002), ch. 4-2, pp. 4-47–4-52.
  15. ↑ Titus (2002), ch. 4-2, pp. 4-49–4-52.
  16. ↑ Titus (2002), ch. 4-2, pp. 4-50–4-52.
  17. ↑ Cote (2008), ch. 15.5, pp. 15-80–15-81.
  18. ↑ Titus (2002), ch. 4-2, pp. 4-52.
  19. ↑ Titus (2002), ch. 4-2, pp. 4-52–4-54.
  20. ↑ Cote (2008), ch. 15.3, pp. 15-53.
  21. ↑ Titus (2002), ch. 4-2, pp. 4-45–4-48.
  22. ↑ 22.0 22.1 Titus (2002), ch. 4-2, pp. 4-47–4-50.
  23. ↑ Cote (2008), ch. 16.3, pp. 16-41–16-42.
  24. ↑ Hopkins et al. (2005), pp. xxxvii–xxxviii.
  25. ↑ Titus (2002), ch. 4-2, pp. 4-68–4-70.
  26. ↑ Cote (2008), ch. 15.6, pp. 15-89–15-94.
  27. ↑ Fleming (2002), ch. 4-3, pp. 4-83–4-84.
  28. ↑ Hopkins et al. (2005), pp. xxxvii–xlii.
  29. ↑ 29.0 29.1 29.2 Cote (2008), ch. 15.3, pp. 15-46–15-47.
  30. ↑ Cote (2008), ch. 15.2, pp. 15-23–15-24.
  31. ↑ Cote (2008), ch. 16.11, pp. 16-210–16-211.
  32. ↑ Cote (2008), ch. 16.11, pp. 16-220.

References

  • Cote, A. E. (Ed.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
  • Fleming, R. P. (2002). Automatic sprinkler system calculations. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-72–4-87). National Fire Protection Association.
  • Hopkins, M., Schoenrock, J., & Budnick, E. (2005). Fire suppression systems (NIST NCSTAR 1-4B). National Institute of Standards and Technology.
  • Titus, J. J. (2002). Hydraulics. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-44–4-71). National Fire Protection Association.