NFPA wiki: fact-check corrections (written by Claude Opus 5.5) |
Add watermarked Fire Safety Academy illustration at the location specified in the visual plan |
||
| Line 58: | Line 58: | ||
== Use in fire protection and emergency response == | == Use in fire protection and emergency response == | ||
Sheets are a basic input to [[pre-incident planning]]. Serapiglia advises that pre-incident plans for industrial sites review the sheets for hazardous materials. The plan should record where the files are kept and who on site is responsible for them, for example in a lockbox shown on the facility drawing. For large chemical inventories, electronic copies on discs, portable drives or laptops can be considered.<ref name="Ser-12-295" /> In plastics plants, Ouellette recommends that personnel be trained in the sheets for each plastic, additive and solvent they use, because the sheet explains the hazards of each material in a fire.<ref name="Ou-9-64">Ouellette (2008), p. 9-64.</ref> | Sheets are a basic input to [[pre-incident planning]]. Serapiglia advises that pre-incident plans for industrial sites review the sheets for hazardous materials. The plan should record where the files are kept and who on site is responsible for them, for example in a lockbox shown on the facility drawing. For large chemical inventories, electronic copies on discs, portable drives or laptops can be considered.<ref name="Ser-12-295" /> In plastics plants, Ouellette recommends that personnel be trained in the sheets for each plastic, additive and solvent they use, because the sheet explains the hazards of each material in a fire.<ref name="Ou-9-64">Ouellette (2008), p. 9-64.</ref> | ||
[[File:fse-safety-data-sheet-v4.jpg|thumb|upright=1.5|alt=Wall-mounted emergency information box opened to show data sheet binders, site plan and contact list|An emergency information box at a facility entrance holds data sheets, the site plan and contact numbers for the fire department. Based on Serapiglia (2008), p. 12-295, and Whitford (2008), p. 6-236.]] | |||
At community level, the US local emergency planning committee obtains and distributes information on the hazardous materials stored and used in its area. The chemical name or the sheet gives the product name, its hazards and the control methods for routine and emergency situations.<ref name="Jen-12-48">Jenaway (2008), p. 12-48.</ref> Jenaway notes that this information can show, for example, that a fire department needs large quantities of foam concentrate or extensive spill control equipment.<ref name="Jen-12-48" /> Under Section 311 of SARA Title III, a facility must submit the sheet for each hazardous chemical covered by OSHA rules to three bodies. These are the local emergency planning committee, the state emergency response commission and the fire department. It may submit a list of the chemicals instead, and a revised sheet is due within three months of significant new information.<ref name="HN-13-86" /> | At community level, the US local emergency planning committee obtains and distributes information on the hazardous materials stored and used in its area. The chemical name or the sheet gives the product name, its hazards and the control methods for routine and emergency situations.<ref name="Jen-12-48">Jenaway (2008), p. 12-48.</ref> Jenaway notes that this information can show, for example, that a fire department needs large quantities of foam concentrate or extensive spill control equipment.<ref name="Jen-12-48" /> Under Section 311 of SARA Title III, a facility must submit the sheet for each hazardous chemical covered by OSHA rules to three bodies. These are the local emergency planning committee, the state emergency response commission and the fire department. It may submit a list of the chemicals instead, and a revised sheet is due within three months of significant new information.<ref name="HN-13-86" /> | ||
Revision as of 08:18, 8 November 2026
A safety data sheet is a document, prepared by the manufacturer or importer of a chemical product, that describes the physical and health hazards of the product and the recommended emergency action.[1][2] In US practice up to at least 2008 it was called a material safety data sheet (MSDS).[1][3] In the United States the sheet was required by the Hazard Communication Standard of the Occupational Safety and Health Administration (OSHA), 29 CFR 1910.1200.[3] It gives the composition, physical and chemical properties, health and safety hazards, emergency response and waste disposal information for a material.[3]
For fire protection, the sheet is a typical source of data such as the flash point, ignition temperature and flammable range of a product.[4] Fire departments use it in pre-incident plans, and under US law in 2008 facilities had to submit it to local emergency planners and the fire department.[5][6] The sheet has limits. Much of its data applies at atmospheric temperature and pressure rather than at process conditions, and sheets for single products are of little use when several products burn together.[7][8]
Definition and legal basis
A US Nuclear Regulatory Commission report gives a glossary definition of the material safety data sheet. It reads: "a document, prepared in accordance with DOL 29 CFR, that contains information regarding the physical and health hazards associated with a given product or substance and a recommended emergency action".[1] Wright describes the sheet as a facility document, as opposed to the shipping papers that travel with a load in transport.[3] Davenport, describing US practice in 2008, adds that all manufacturers were required by law to prepare and distribute such sheets for all the products they made.[9]
The Hazard Communication Standard (HCS) was first issued by OSHA in November 1983. At the time of the 2008 handbook its most recent revision dated from 11 March 1994, and it covered manufacturers, importers, distributors and users of hazardous chemicals.[10] The standard is commonly called the right-to-know law or HAZCOM. It requires manufacturers and handlers of hazardous materials to develop written sheets for specific types of hazardous chemicals and to make them available to employees who ask for information about a chemical in the workplace.[10] Hildebrand and Noll note that OSHA requires a sheet for more than 500,000 chemicals and mixtures.[6]
The sheet sits beside two other routes for hazard information. Containers carry labels, and in transport the shipping papers carry the emergency response information for the commodity.[2][3] At the community level, the community right-to-know provisions of the Superfund Amendments and Reauthorization Act of 1986 (SARA Title III) use the same sheets as the basis for reporting chemicals to local planners.[6]
Content
Under the US standard as summarised in 2008, each sheet had to be in English. It had to give the specific chemical identity and the common names, and the physical and chemical characteristics of the hazardous chemical. It also had to state the known acute and chronic health effects, the exposure limits and whether the chemical is considered a carcinogen. Precautionary measures, emergency and first aid procedures and the organisation that prepared the sheet completed the list.[11] The regulation did not require a specific form. OSHA published a model form (OSHA form 174) with nine sections, and many manufacturers used the ANSI Z400.1 standard as a uniform format.[11]
| No. | Section | No. | Section |
|---|---|---|---|
| 1 | Chemical identity | 6 | Health-hazard information |
| 2 | Hazardous ingredients | 7 | Precautions for safe handling |
| 3 | Physical and chemical characteristics | 8 | Use of the material |
| 4 | Fire and explosion hazard data | 9 | Control measures |
| 5 | Reactivity details |
Wright gives a similar list from the responder's point of view. Sheets typically describe the physical and chemical characteristics, the physical hazards, the health hazards and the signs and symptoms of exposure. They also give the routes of entry, the permissible exposure limits, the responsible party, the precautions for safe handling and spill cleanup, the control measures including personal protective equipment, and emergency and first aid procedures.[12] Davenport summarises the content as information on toxicity, flammability, reactivity and stability, with safe handling and storage practices.[9]
A cross-reference of common response guides in the handbook shows which physical and fire data are typically found on a sheet. The fire-related items are the flash point, the ignition temperature, the flammable range, the vapour pressure, the vapour density, the boiling point and the toxic products of combustion.[4] The same table marks the sheet as a typical source for what the material is reactive to, in other words its chemical incompatibilities. It also covers health limits such as the IDLH concentration, LD50 and LC50 values and exposure limits, together with extinguishing agents, protective equipment, decontamination and first aid.[4]
| Group | Items typically found on the sheet | Not marked for the sheet |
|---|---|---|
| Identity | DOT identification number, synonyms, hazard class, form, colour, odour, chemical formula, molecular weight | STCC number, NFPA 704 marking |
| Physical data | Boiling point, melting point, vapour pressure, specific gravity, vapour density, solubility | Expansion ratio |
| Fire data | Flash point, ignition temperature, flammable range, toxic products of combustion, extinguishing agents | |
| Reactivity and health | Reactive to what, odour threshold, IDLH, LD50, LC50, threshold limit values, PEL, route of entry | Toxicity rating |
| Response | Evacuation distances, first aid, personal protective equipment, decontamination, neutralising agents |
Duties under the Hazard Communication Standard
The standard as described in 2008 divides the work among three groups. Chemical manufacturers and importers determine the hazards of each product. Manufacturers, importers and distributors pass the hazard information and protective measures downstream to customers through labels and sheets. Employers list all hazardous chemicals in the workplace, obtain the labels and sheets, run a written hazard communication programme and train their employees.[2]
Hazard determination comes first. Manufacturers and importers must review the scientific information on the chemicals they produce or import and report what they find to their employees and to the employers who use the products. Downstream employers can rely on these evaluations.[10] Each chemical must be evaluated for adverse health effects and for physical hazards such as flammability, and suspected or confirmed carcinogens must be reported as such.[2] The sheet must be supplied automatically with the first shipment of a hazardous chemical to a downstream distributor or user, and distributors must pass it on in turn.[2]
In the workplace, copies of the sheets for the hazardous chemicals in a work area must be readily accessible to the employees there.[11] The employer's written programme covers container labelling, the collection and availability of the sheets, employee training and a list of the hazardous chemicals present. It also covers non-routine tasks and chemicals in unlabelled pipes, and on sites with several employers the information must be shared between them.[2] Training must cover how a release can be detected, for example by monitoring or by the appearance or odour of the chemical, the physical and health hazards and the protective measures employees can take.[11] Under HAZCOM, health exposure information should also be given to emergency responders when an incident is closed down, and all exposures should be documented.[10]
Trade secrets are a recognised gap. A manufacturer may withhold the specific chemical identity, meaning the chemical name, the Chemical Abstracts Service (CAS) registry number or any other information revealing the precise designation, but not the common names. The standard balances this against worker protection by allowing limited disclosure to health professionals under conditions of need and confidentiality. In a medical emergency, the identity must be disclosed immediately to the treating physician or nurse, and a written statement of need can follow later.[11]
Use in fire protection and emergency response
Sheets are a basic input to pre-incident planning. Serapiglia advises that pre-incident plans for industrial sites review the sheets for hazardous materials. The plan should record where the files are kept and who on site is responsible for them, for example in a lockbox shown on the facility drawing. For large chemical inventories, electronic copies on discs, portable drives or laptops can be considered.[5] In plastics plants, Ouellette recommends that personnel be trained in the sheets for each plastic, additive and solvent they use, because the sheet explains the hazards of each material in a fire.[13]

At community level, the US local emergency planning committee obtains and distributes information on the hazardous materials stored and used in its area. The chemical name or the sheet gives the product name, its hazards and the control methods for routine and emergency situations.[14] Jenaway notes that this information can show, for example, that a fire department needs large quantities of foam concentrate or extensive spill control equipment.[14] Under Section 311 of SARA Title III, a facility must submit the sheet for each hazardous chemical covered by OSHA rules to three bodies. These are the local emergency planning committee, the state emergency response commission and the fire department. It may submit a list of the chemicals instead, and a revised sheet is due within three months of significant new information.[6]
During an incident, the sheet is one of the sources used to identify a material at a fixed facility, together with the pre-emergency plan, markings and contact with the facility manager.[3] Sheets are available from facility managers and may also be found in transport. If none is available locally, the Chemical Transportation Emergency Center (CHEMTREC) held more than 500,000 sheets on file at the time of the handbook.[12] In Wright's cross-reference, however, the sheet is a secondary resource. The primary resources in that table are the Emergency Response Guidebook and the NIOSH Pocket Guide to Chemical Hazards.[15][4] Wright notes that no single printed source provides all the information, so in hazardous materials response more than one resource may have to be consulted.[12]
Use in hazard and risk analysis
Sheets are also a starting point for engineering analysis. In the process safety information that Snyder describes for industrial loss prevention, the material hazards documentation for each chemical must give flammability, thermal stability, reaction and toxicity data. In many cases the sheets satisfy this requirement, provided they contain the necessary details.[16] Barry lists material information from the sheets first in his checklist of data needed for quantitative risk assessment in chemical process industries.[8] He notes that only some of the required property data can be obtained from the sheet. The full list includes thermodynamic data, flammability, dust explosion data, toxicity, shock sensitivity and properties such as susceptibility to spontaneous ignition.[8]
Both Snyder and Barry warn that much of the published data, including that on the sheets, applies at atmospheric temperature and pressure. Experimental data for the actual process conditions will sometimes be needed.[8][16] In building fire risk analysis, Meacham describes safety reviews that may require review of the sheets. He also describes hazard and operability (HazOp) studies, which take a checklist, a sheet, or a flow chart of a process and systematically ask questions about the outcome of specific actions.[17]
Pesticides as an example
Pesticide storage shows both the value and the limits of the sheet. Whitford calls the sheet the best method for determining the hazards of a pesticide's active and inert ingredients. Sheets should be available in all emergencies, because they give quick access to product information and, through the emergency telephone number, to specialists who can help. Additional current sets should be kept off site and given to the fire department and local hospitals, for example in an emergency response information mailbox.[7] Whitford considers the emergency number on the sheet an excellent source of quick and reliable advice.[18] Adequate preplanning requires evaluation of the sheet for each formulation, and the response organisation must be able to interpret how the properties of the stored products change its approach.[19]
The same chapter shows the limits. Sheets and all the hazard data used to identify single products are of little use when multiple products are engulfed in a fire.[7] The inert ingredients of a formulation are not specifically identified on the product label or on the sheet, although some sheets list their hazards.[20] Information on the synergistic effects of a fire or of a release involving a mixture of pesticides is not available from any source.[21] Whitford nevertheless concludes that in many respects the sheet is the key source of information on any emergency involving pesticides.[22] These gaps are part of the wider subject of pesticide fire hazards.
Limits and common misconceptions
A sheet describes a product, not a situation. Much of its data applies at atmospheric temperature and pressure, while real incidents may involve process conditions or fires in which several products burn together.[8][7] For pesticides, Whitford notes that information on the synergistic effects of a fire or release involving a mixture of products is not available from any source, so the separate sheets cannot supply it.[21]
The nine-section layout shown above was a model, not a required format. Under the US rules described in 2008 no specific form was required; the OSHA model form and ANSI Z400.1 were formats that many manufacturers chose to use.[11] Sheets prepared under those rules could therefore arrange the information differently from one supplier to the next. The NFPA 704 hazard diamond is a separate system: Wright's cross-reference does not mark the NFPA 704 marking as typically found on the sheet.[4]
The sheet is also not a complete disclosure. A bona fide trade secret can keep the specific chemical identity off the sheet, with disclosure limited to health professionals.[11] Finally, the legal requirements summarised here are those of the United States as described in the 2008 handbook. They should not be taken as current rules or as the rules of other countries.[10]
See also
- Hazardous waste
- NFPA 704
- Hazardous materials placarding
- Flammable and combustible liquid classification
Notes
- ↑ 1.0 1.1 1.2 Iqbal and Salley (2004), p. F-41.
- ↑ 2.0 2.1 2.2 2.3 2.4 2.5 Hildebrand and Noll (2008), p. 13-91.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 C. J. Wright (2008a), p. 13-126.
- ↑ 4.0 4.1 4.2 4.3 4.4 C. J. Wright (2008a), p. 13-131.
- ↑ 5.0 5.1 Serapiglia (2008), p. 12-295.
- ↑ 6.0 6.1 6.2 6.3 Hildebrand and Noll (2008), p. 13-86.
- ↑ 7.0 7.1 7.2 7.3 Whitford (2008), p. 6-236.
- ↑ 8.0 8.1 8.2 8.3 8.4 Barry (2002), p. 5-178.
- ↑ 9.0 9.1 Davenport (2008), p. 7-43.
- ↑ 10.0 10.1 10.2 10.3 10.4 Hildebrand and Noll (2008), p. 13-90.
- ↑ 11.0 11.1 11.2 11.3 11.4 11.5 11.6 Hildebrand and Noll (2008), p. 13-92.
- ↑ 12.0 12.1 12.2 C. J. Wright (2008a), p. 13-127.
- ↑ Ouellette (2008), p. 9-64.
- ↑ 14.0 14.1 Jenaway (2008), p. 12-48.
- ↑ C. J. Wright (2008a), p. 13-130.
- ↑ 16.0 16.1 Snyder (2008), p. 12-184.
- ↑ Meacham (2002), p. 5-155.
- ↑ Whitford (2008), p. 6-240.
- ↑ Whitford (2008), p. 6-243.
- ↑ Whitford (2008), p. 6-237.
- ↑ 21.0 21.1 Whitford (2008), pp. 6-237–6-238.
- ↑ Whitford (2008), p. 6-238.
References
- Barry, T. F. (2002). Quantitative risk assessment in chemical process industries. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 5-176–5-213). National Fire Protection Association; Society of Fire Protection Engineers.
- Davenport, J. A. (2008). Storage and handling of chemicals. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-43–7-55). National Fire Protection Association.
- Hildebrand, M. S., & Noll, G. G. (2008). Public fire protection and hazmat management. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-81–13-98). National Fire Protection Association.
- Iqbal, N., & Salley, M. H. (2004). Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
- Jenaway, W. F. (2008). Needs assessment and hazard analysis. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-41–12-50). National Fire Protection Association.
- Meacham, B. J. (2002). Building fire risk analysis. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 5-153–5-175). National Fire Protection Association; Society of Fire Protection Engineers.
- Ouellette, G. (2008). Plastics industry and related process hazards. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-53–9-65). National Fire Protection Association.
- Serapiglia, M. J. (2008). Pre-Incident planning for industrial and municipal emergency response. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-289–12-298). National Fire Protection Association.
- Snyder, M. (2008). Industrial fire loss prevention. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 12-177–12-198). National Fire Protection Association.
- Whitford, F. (2008). Pesticides in the workplace. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-233–6-245). National Fire Protection Association.
- Wright, C. J. (2008a). Managing the response to hazardous material incidents. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-117–13-144). National Fire Protection Association.