New FSE wiki article: Motor vehicle fire (written by Claude Opus 5.5) |
FSE wiki: fact-check: correct crash-fire scope, historical rules and design-fire qualifiers (written by Claude Opus 5.5) |
||
| Line 1: | Line 1: | ||
A '''motor vehicle fire''' is a fire in a self-propelled road vehicle, such as a passenger car, van, bus or truck. Like any fire it needs a flammable substance, an ignition source and oxygen | A '''motor vehicle fire''' is a fire in a self-propelled road vehicle, such as a passenger car, van, bus or truck. Like any fire it needs a flammable substance, an ignition source and oxygen; petrol and diesel vehicles carry fuel, while upholstery, wiring insulation and plastic trim can burn regardless of power source.<ref name="Routhier-21-15">Routhier (2008), p. 21-15.</ref> In the United States, vehicle fires made up 20.1% of reported fires and 13.5% of civilian fire deaths in 2000–2004, excluding the 11 September 2001 deaths.<ref name="HallCote-3-21">Hall and Cote (2008), p. 3-21.</ref> In the cited US data, most highway vehicle fires started in the engine area, while fires following a collision caused a far larger share of the deaths.<ref name="Routhier-21-17">Routhier (2008), p. 21-17.</ref><ref name="Ahrens-3-78">Ahrens et al. (2008), p. 3-78.</ref><ref name="Long-21-6">Long et al. (2008), p. 21-6.</ref> Example values for a car are an energy content of 6,000 to 12,000 MJ and a peak heat release rate of 8.5 MW.<ref name="VR-4.4">Van Rossum (2027), §4.4.</ref><ref name="VR-4.5">Van Rossum (2027), §4.5.</ref> Car fires are used as design fires for indoor car parks and road tunnels.<ref name="NIPV-24">Van der Graaf et al. (2021/2023), p. 24.</ref><ref name="Bendelius-21-204">Bendelius (2008), p. 21-204.</ref> | ||
== Definition and classification == | == Definition and classification == | ||
Vehicle fire hazard depends on vehicle type, use, climate, age, condition and maintenance.<ref name="Routhier-21-15" /> It also depends on the construction standards for the fuel and electrical systems and on the fuel itself: petrol (gasoline in US sources), diesel, propane, natural gas or alcohol. Besides the fuel, upholstery, insulating and sound-deadening materials, wiring insulation and plastic body parts can feed the fire. Cargo carried in or on the vehicle, particularly by trucks, may also be flammable.<ref name="Routhier-21-15" /> Buses, trucks and tank vehicles are treated in [[Commercial vehicle fire]], and vehicles running on gaseous and other alternative fuels in [[Alternative fuel vehicle]]. | |||
Statistical systems draw the boundaries of the term in different ways. In the US National Fire Incident Reporting System (NFIRS), version 5.0, a vehicle burning inside a structure counts as a vehicle fire unless the structure itself becomes involved.<ref name="AhrensStewart-3-49">Ahrens and Stewart (2008), p. 3-49.</ref> Once the building is involved, the incident becomes a structure fire, and the vehicle is recorded as mobile property. Analyses of passenger vehicle fires differ in whether pickups, buses, motorcycles and trailers are counted, so their estimates differ.<ref name="Long-21-5">Long et al. (2008), p. 21-5.</ref> | Statistical systems draw the boundaries of the term in different ways. In the US National Fire Incident Reporting System (NFIRS), version 5.0, a vehicle burning inside a structure counts as a vehicle fire unless the structure itself becomes involved.<ref name="AhrensStewart-3-49">Ahrens and Stewart (2008), p. 3-49.</ref> Once the building is involved, the incident becomes a structure fire, and the vehicle is recorded as mobile property. Analyses of passenger vehicle fires differ in whether pickups, buses, motorcycles and trailers are counted, so their estimates differ.<ref name="Long-21-5">Long et al. (2008), p. 21-5.</ref> | ||
| Line 9: | Line 9: | ||
== Fire statistics in the United States == | == Fire statistics in the United States == | ||
The statistics below are US data, mostly from around 2000. [[Fire statistics]] show that vehicle fires accounted for 20.1% of reported fires and 13.5% of civilian deaths in 2000–2004; the death share excludes 11 September 2001.<ref name="HallCote-3-21" /> They caused nearly three times as many fire deaths as all structures other than homes. The number of highway vehicle fires fell from 411,300 in 1980 to 281,600 in 2002, almost one third fewer.<ref name="Routhier-21-16">Routhier (2008), p. 21-16.</ref> The annual average for 1999–2002 was 269,900 fires, 380 civilian deaths and 1,310 civilian injuries. | |||
About 32,000 occupants of passenger vehicles died each year in traffic crashes in the United States.<ref name="Long-21-4">Long et al. (2008), p. 21-4.</ref> About 1.2% of these deaths, or 385 a year, were attributed to fires after a collision, and a further 40 a year to fires without a collision. Postcollision fires thus accounted for 90% of passenger vehicle fire deaths in 1999–2004.<ref name="Long-21-6" /> In about half of the deaths from unintentional fires without a collision, the occupant was asleep or impaired by alcohol or other drugs. | About 32,000 occupants of passenger vehicles died each year in traffic crashes in the United States.<ref name="Long-21-4">Long et al. (2008), p. 21-4.</ref> About 1.2% of these deaths, or 385 a year, were attributed to fires after a collision, and a further 40 a year to fires without a collision. Postcollision fires thus accounted for 90% of passenger vehicle fire deaths in 1999–2004.<ref name="Long-21-6" /> In about half of the deaths from unintentional fires without a collision, the occupant was asleep or impaired by alcohol or other drugs.<ref name="Long-21-6" /> Routhier reported approximately 6,200 collision-related highway vehicle fires a year.<ref name="Routhier-21-15" /> | ||
The risk has fallen over time. For cars and light trucks of model year 1978 and earlier, the risk of a fire death was 3.7 per million registered vehicles per year.<ref name="Long-21-7">Long et al. (2008), p. 21-7.</ref> For model years 1996–2004 it was 1.8, and per billion vehicle miles travelled it dropped from 0.42 to 0.13, almost 70% lower. This happened while vehicles contained more plastics: 7.6% of the weight of highway vehicles in 2004 against 5.0% in 1978, | The risk has fallen over time. For cars and light trucks of model year 1978 and earlier, the risk of a fire death was 3.7 per million registered vehicles per year.<ref name="Long-21-7">Long et al. (2008), p. 21-7.</ref> For model years 1996–2004 it was 1.8, and per billion vehicle miles travelled it dropped from 0.42 to 0.13, almost 70% lower. This happened while vehicles contained more plastics: 7.6% of the weight of highway vehicles in 2004 against 5.0% in 1978, and 117 kg in a typical passenger car.<ref name="Long-21-4" /> Older vehicles burn more often, and the median age of US passenger cars rose by 50% to almost 9 years between 1980 and 2004.<ref name="Long-21-3">Long et al. (2008), p. 21-3.</ref> | ||
These numbers have known limits. NFIRS captures only one third to one half of US fire incidents, so analysts scale it up with the NFPA annual survey.<ref name="Long-21-6" /> About half of all passenger vehicle fires in NFIRS have no factor contributing to ignition recorded. | These numbers have known limits. NFIRS captures only one third to one half of US fire incidents, so analysts scale it up with the NFPA annual survey.<ref name="Long-21-6" /> About half of all passenger vehicle fires in NFIRS have no factor contributing to ignition recorded. The NFPA/NFIRS estimate of passenger vehicle fire deaths is about 8% higher than the FARS estimate.<ref name="Long-21-6" /> | ||
== Causes and areas of origin == | == Causes and areas of origin == | ||
Ignition sources in vehicles include electrical short circuits, sparks from the engine ignition system, hot exhaust parts and engine backfire.<ref name="Routhier-21-15" /> Overheated tyres, brakes and wheel bearings, friction sparks from a collision or from metal scraping on the road, and careless smoking add to the list.<ref name="Routhier-21-16" /> In NFIRS data for 1999–2002, mechanical failure or malfunction contributed to 48% of | Ignition sources in vehicles include electrical short circuits, sparks from the engine ignition system, hot exhaust parts and engine backfire.<ref name="Routhier-21-15" /> Overheated tyres, brakes and wheel bearings, friction sparks from a collision or from metal scraping on the road, and careless smoking add to the list.<ref name="Routhier-21-15-16">Routhier (2008), pp. 21-15–21-16.</ref> In NFIRS data for US highway vehicle fires in 1999–2002, mechanical failure or malfunction contributed to 48% of the fires but only 9% of the deaths.<ref name="Ahrens-3-78" /> Electrical failure contributed to 23% of the fires and 2% of the deaths. Collisions, knock-downs, run-overs and roll-overs contributed to only 3% of the fires but to 57% of the deaths. | ||
The area of origin shows the same pattern. In 1999–2003, the engine area, running gear or wheel area was the origin of 65% of US highway vehicle fires and 39% of the deaths.<ref name="Routhier-21-17" /> The operator or passenger area accounted for 17% of the fires and 20% of the deaths. Fires starting at the fuel tank or fuel line made up only 2% of the fires but 17% of the deaths. This corresponds to about 15 deaths per 1,000 fuel system fires, against about 1.4 per 1,000 for all highway vehicle fires. | The area of origin shows the same pattern. In 1999–2003, the engine area, running gear or wheel area was the origin of 65% of US highway vehicle fires and 39% of the deaths.<ref name="Routhier-21-17" /> The operator or passenger area accounted for 17% of the fires and 20% of the deaths. Fires starting at the fuel tank or fuel line made up only 2% of the fires but 17% of the deaths. This corresponds to about 15 deaths per 1,000 fuel system fires, against about 1.4 per 1,000 for all highway vehicle fires. | ||
Studies of postcollision fires show two main types: fuel-fed [[Pool fire|pool fires]] of petrol, and fires that start in the engine compartment.<ref name="Long-21-6" /> | Studies of postcollision fires show two main types: fuel-fed [[Pool fire|pool fires]] of petrol, and fires that start in the engine compartment.<ref name="Long-21-6" /> Of the US postcollision passenger vehicle fire deaths in 1999–2004, 63% involved fires in which petrol was ignited first, and 48% involved fires that began in the engine area, running gear or wheel area.<ref name="Long-21-7" /> In the United States in 1994–1998, fuel-fed fires made up 27% of highway vehicle fires but caused 56% of the vehicle fire deaths.<ref name="Long-21-9">Long et al. (2008), p. 21-9.</ref> Routhier (2008) identified rear-end collisions as a fuel-tank concern because most US-built vehicles had their tanks at the rear.<ref name="Routhier-21-20">Routhier (2008), pp. 21-20–21-21.</ref> The handbook’s separate review of postcollision fires reported that most fires in one crash sample followed front-end impacts and began in the engine compartment.<ref name="Long-21-9" /> | ||
Several other mechanisms recur. Diesel has a higher flashpoint than petrol, but diesel engines run hotter, so warm fuel leaking onto a hot surface can still ignite.<ref name="Routhier-21-21">Routhier (2008), p. 21-21.</ref> Catalytic converters can start wildland fires when cars are driven through dry grass, and overused brakes can overheat until they smoulder or burn. Vehicles are also the main fire risk at service stations: in 1994–1998, 62% of fires at US public service stations were classed as vehicle fires.<ref name="Rivkin-21-29">Rivkin (2008a), p. 21-29.</ref> | Several other mechanisms recur. Diesel has a higher flashpoint than petrol, but diesel engines run hotter, so warm fuel leaking onto a hot surface can still ignite.<ref name="Routhier-21-21">Routhier (2008), p. 21-21.</ref> Catalytic converters can start wildland fires when cars are driven through dry grass, and overused brakes can overheat until they smoulder or burn. Vehicles are also the main fire risk at service stations: in 1994–1998, 62% of fires at US public service stations were classed as vehicle fires.<ref name="Rivkin-21-29">Rivkin (2008a), p. 21-29.</ref> | ||
== Fire development and heat release rate == | == Fire development and heat release rate == | ||
In full-scale tests after severe crash tests, the time to untenable conditions in the passenger compartment was strongly linked to the moment flames entered it.<ref name="Long-21-9" /> Flames from an engine compartment fire entered through the failed windshield, the heating and air-conditioning vents or openings in the bulkhead. In the pool fire tests, flames entered through gaps around deformed doors or underbody seams, and conditions became untenable after 1.6 to 4.0 minutes. In pool fires, [[Tenability criteria|untenable conditions]] can thus arise much faster than emergency personnel can respond.<ref name="Long-21-10">Long et al. (2008), p. 21-10.</ref> The | In full-scale tests after severe crash tests, the time to untenable conditions in the passenger compartment was strongly linked to the moment flames entered it.<ref name="Long-21-9" /> Flames from an engine compartment fire entered through the failed windshield, the heating and air-conditioning vents or openings in the bulkhead. In the pool fire tests, flames entered through gaps around deformed doors or underbody seams, and conditions became untenable after 1.6 to 4.0 minutes. In pool fires, [[Tenability criteria|untenable conditions]] can thus arise much faster than emergency personnel can respond.<ref name="Long-21-10">Long et al. (2008), p. 21-10.</ref> The power output of the initial pool fire is set by the size of the fuel pool rather than by the flammability of the vehicle materials.<ref name="Long-21-9" /> | ||
The interior adds its own fuel. Because the US interior materials test is lax, seating in cars is commonly easily ignitable and produces rapidly growing fires with a high heat release.<ref name="Babrauskas-6-116">Babrauskas (2008b), p. 6-116.</ref> Major parts of newer vehicles are plastic, and these materials can cause severe fires with copious amounts of smoke.<ref name="Moore-20-169">J. Moore (2008), pp. 20-168–20-169.</ref> A Dutch | The interior adds its own fuel. Because the US interior materials test is lax, seating in cars is commonly easily ignitable and produces rapidly growing fires with a high heat release.<ref name="Babrauskas-6-116">Babrauskas (2008b), p. 6-116.</ref> Major parts of newer vehicles are plastic, and these materials can cause severe fires with copious amounts of smoke.<ref name="Moore-20-169">J. Moore (2008), pp. 20-168–20-169.</ref> A Dutch report on indoor car parks states that modern cars, with their high plastic content, have a greater fire load and a higher heat release rate than older steel models.<ref name="NIPV-11">Van der Graaf et al. (2021/2023), p. 11.</ref> | ||
The [[Heat release rate]] of single cars varies widely. In tests at the | The [[Heat release rate]] of single cars varies widely. In tests at the Fire Research Station (FRS), a 1982 Austin Maestro reached a peak of 8.5 MW and a 1986 Citroën BX a peak of 4.5 MW.<ref name="Babrauskas-3-27">Babrauskas (2002b), p. 3-27.</ref> Three cars from the late 1970s tested at VTT each peaked at about 1.5–2.0 MW. The reason for this spread is not fully clear, but it is not the share of polymers in the cars. In the published curves, both FRS cars peaked roughly 15 minutes into the test. | ||
A literature review summarised in a report of the Netherlands Institute for Public Safety (NIPV) found a typical peak of about 6 MW for cars with combustion engines.<ref name="NIPV-25">Van der Graaf et al. (2021/2023), p. 25.</ref> The average times to reach the peak ranged from 6 to 35 minutes, and the total heat released was 3.3 to 10 GJ. This | A literature review summarised in a report of the Netherlands Institute for Public Safety (NIPV) found a typical peak of about 6 MW for cars with combustion engines.<ref name="NIPV-25">Van der Graaf et al. (2021/2023), p. 25.</ref> The average times to reach the peak ranged from 6 to 35 minutes, and the total heat released was 3.3 to 10 GJ. This matches the order of the 6,000 to 12,000 MJ example for a car.<ref name="VR-4.4" /> A typical car fire burns for just over half an hour, with a maximum of about 5 MW after about 10–15 minutes.<ref name="NIPV-26">Van der Graaf et al. (2021/2023), p. 26.</ref> With petrol at about 32 MJ/litre, a full 50 litre tank holds about 1.6 GJ, or roughly 13–27% of that energy content.<ref name="NIPV-25" /> | ||
In fire tests on electric and conventional cars, similar temperatures of about 800 ± 100 °C were measured for 5 to 30 minutes.<ref name="NIPV-23">Van der Graaf et al. (2021/2023), p. 23.</ref> Smoke from some plastic materials, such as the interior of a burning car, caused severe effects when only a small amount was inhaled.<ref name="Purser-2-112">Purser (2002), p. 2-112.</ref> Battery packs add [[Hydrogen fluoride|hydrogen fluoride]] to the smoke, as described in [[Electric vehicle fire]], but the plastic parts of any burning car already produce severely toxic smoke.<ref name="NIPV-26" /><ref name="NIPV-30">Van der Graaf et al. (2021/2023), p. 30.</ref> | In fire tests on electric and conventional cars, similar temperatures of about 800 ± 100 °C were measured for 5 to 30 minutes.<ref name="NIPV-23">Van der Graaf et al. (2021/2023), p. 23.</ref> Smoke from some plastic materials, such as the interior of a burning car, caused severe effects when only a small amount was inhaled.<ref name="Purser-2-112">Purser (2002), p. 2-112.</ref> Battery packs add [[Hydrogen fluoride|hydrogen fluoride]] to the smoke, as described in [[Electric vehicle fire]], but the plastic parts of any burning car already produce severely toxic smoke.<ref name="NIPV-26" /><ref name="NIPV-30">Van der Graaf et al. (2021/2023), p. 30.</ref> | ||
== Design fires and calculation == | == Design fires and calculation == | ||
Indoor car park design uses a [[Design fire|design fire]]: a heat release rate curve over time.<ref name="NIPV-24" /> In New Zealand, Verification Method C/VM2 (second edition, 2025) prescribes a pre-flashover growth of 0.0117''t''² kW for car parks without stacking systems.<ref name="CVM2-20">Ministry of Business, Innovation and Employment (2025b), p. 20.</ref> That car park design scenario grows to a peak of 20 MW, with a heat of combustion of 20 MJ/kg, a soot yield of 0.07 kg/kg and a radiative fraction of 0.35. In a computational fluid dynamics model the burning area follows from 500 to 1,000 kW/m², and in a zone model from 250 kW/m². The design [[Fire load|fire load]] energy density for car parks is 400 MJ/m².<ref name="CVM2-22">Ministry of Business, Innovation and Employment (2025b), p. 22.</ref> | |||
The commentary to the first edition of C/VM2 explains why car parks get their own growth rate. Car parks are one of the few risk groups in which the fuel can be bounded and its layout is controlled.<ref name="CVM2C-55">Ministry of Business, Innovation and Employment (2013), p. 55.</ref> A literature review showed that the early growth of car fires can be modelled as a medium [[t-squared fire]]. In the Netherlands, the standard NEN 6098 for smoke control in mechanically ventilated car parks uses a design curve based on a 1999 design fire by TNO.<ref name="VR-8.6">Van Rossum (2027), §8.6.</ref> In the underlying tests, the fire could spread to the neighbouring cars 10–15 minutes after the first car, depending on their spacing. The curve includes intervention by the fire brigade, and three cars | The commentary to the first edition of C/VM2 explains why car parks get their own growth rate. Car parks are one of the few risk groups in which the fuel can be bounded and its layout is controlled.<ref name="CVM2C-55">Ministry of Business, Innovation and Employment (2013), p. 55.</ref> A literature review showed that the early growth of car fires can be modelled as a medium [[t-squared fire]]. In the Netherlands, the standard NEN 6098 for smoke control in mechanically ventilated car parks uses a design curve based on a 1999 design fire by TNO.<ref name="VR-8.6">Van Rossum (2027), §8.6.</ref> In the underlying tests, the fire could spread to the neighbouring cars 10–15 minutes after the first car, depending on their spacing. The curve includes intervention by the fire brigade, and represents three cars burning 15 minutes after ignition. | ||
In the t-squared model, the heat release rate grows with the square of the time since effective ignition. A growth coefficient sets how fast the fire grows, and the time to reach a given size follows by rearranging the equation. Integrating the curve over time gives the energy released so far, which can be compared with the energy content of a car. | In the t-squared model, the heat release rate grows with the square of the time since effective ignition. A growth coefficient sets how fast the fire grows, and the time to reach a given size follows by rearranging the equation. Integrating the curve over time gives the energy released so far, which can be compared with the energy content of a car. | ||
| Line 58: | Line 58: | ||
|} | |} | ||
As a worked example, take the C/VM2 coefficient of 0.0117 kW/s² and the guide value of 8,500 kW.<ref name="CVM2-20" /><ref name="VR-4.5" /> The time to reach this peak is the square root of 8,500/0.0117, which is 852 | As a worked example, take the C/VM2 coefficient of 0.0117 kW/s² and the guide value of 8,500 kW.<ref name="CVM2-20" /><ref name="VR-4.5" /> The time to reach this peak is the square root of 8,500/0.0117, which is about 852 s, or 14 minutes. The same curve reaches 5 MW after about 650 s, in line with the 10–15 minutes reported for a typical car fire.<ref name="NIPV-26" /> The energy released up to 852 s is 0.0117 × 852³/3 kJ, or about 2,400 MJ. That is 20–40% of the 6,000 to 12,000 MJ in a car, so much of the fuel is still left at the peak.<ref name="VR-4.4" /> With the fast coefficient of 0.0469 kW/s² used for most buildings, the fire would reach 8.5 MW after about 425 s, half the time.<ref name="CVM2-20" /> | ||
These models have clear limits. | These models have clear limits. According to the 2013 commentary, the growth curves ignore the incipient phase, so C/VM2 may slightly over-predict early growth.<ref name="CVM2C-55" /> Measured peaks from tests are widely spread, from 1.5 to 8.5 MW for single cars.<ref name="Babrauskas-3-27" /> Design curves based on tests from the 1990s may also be less conservative for modern cars, which contain more plastics.<ref name="VR-8.6" /> Fire load values also depend on their source and purpose: a Swiss survey from 1967–69 gave an average of 200 MJ/m² for a parking building, half the New Zealand design value.<ref name="IFEG-3.4">National Research Council of Canada et al. (2005), pp. 3.4-2, 3.4-6.</ref> | ||
== Regulation and vehicle design == | == Regulation and vehicle design == | ||
In the United States, the National Highway Traffic Safety Administration sets Federal Motor Vehicle Safety Standards (FMVSS) for the manufacture and sale of new vehicles.<ref name="Long-21-4" /> By 2008, only four fire-related standards had been issued for new vehicles, and none for vehicles in use.<ref name="Routhier-21-17" /> FMVSS 301, issued in 1968, limits fuel leakage after a crash for cars, trucks and buses with a gross vehicle weight rating up to 4,536 kg (10,000 lb).<ref name="Long-21-4" /><ref name="Long-21-5" /> In the crash tests, leakage may not exceed 28 g from impact until the vehicle stops, 142 g in the next 5 minutes, or 28 g per minute for 25 minutes.<ref name="Routhier-21-17" /> | In the United States, the National Highway Traffic Safety Administration sets Federal Motor Vehicle Safety Standards (FMVSS) for the manufacture and sale of new vehicles.<ref name="Long-21-4" /> By 2008, only four fire-related standards had been issued for new vehicles, and none for vehicles in use.<ref name="Routhier-21-17" /> FMVSS 301, issued in 1968, limits fuel leakage after a crash for cars, trucks and buses with a gross vehicle weight rating up to 4,536 kg (10,000 lb).<ref name="Long-21-4" /><ref name="Long-21-5" /> In the crash tests, leakage may not exceed 28 g (1 oz) from impact until the vehicle stops, 142 g (5 oz) in the next 5 minutes, or 28 g per minute for 25 minutes.<ref name="Routhier-21-17" /> | ||
FMVSS 302, issued in 1972, covers materials in the passenger compartment, such as seat cushions, headlining, trim panels and floor coverings.<ref name="Routhier-21-17" /> A horizontal sample may not burn or spread a flame faster than 102 mm/min (4 in./min).<ref name="Long-21-5" /> The standard was aimed at interior fires caused by matches and cigarettes, and one handbook author calls it remarkable for its laxness.<ref name="Routhier-21-17" /><ref name="Babrauskas-6-116" /> FMVSS 303 and 304 cover the fuel system and the containers of vehicles running on compressed natural gas.<ref name="Long-21-5" /> | FMVSS 302, issued in 1972, covers materials in the passenger compartment, such as seat cushions, headlining, trim panels and floor coverings.<ref name="Routhier-21-17" /> A horizontal sample may not burn or spread a flame faster than 102 mm/min (4 in./min).<ref name="Long-21-5" /><ref name="Routhier-21-18">Routhier (2008), p. 21-18.</ref> The standard was aimed at interior fires caused by matches and cigarettes, and one handbook author calls it remarkable for its laxness.<ref name="Routhier-21-17" /><ref name="Babrauskas-6-116" /> FMVSS 303 and 304 cover the fuel system and the containers of vehicles running on compressed natural gas.<ref name="Long-21-5" /> | ||
Research shows that better test results for a single material do not always make a car safer. | Research shows that better test results for a single material do not always make a car safer. For engine-compartment materials, a study found the [[Cone calorimeter|cone calorimeter]] the most suitable bench-scale test.<ref name="Long-21-10" /> In such tests, a fire-retarded heating and air-conditioning unit released about 5 kW/m², against more than 200 kW/m² for untreated polypropylene.<ref name="Long-21-11">Long et al. (2008), p. 21-11.</ref> In full-scale burns of two otherwise identical crashed cars, however, the heat release rates and times to untenable conditions were essentially the same. The fire-retarded unit even produced higher levels of toxic gases. For this reason, the authors argue for a systems approach that weighs fire performance against crash protection, durability and toxicity.<ref name="Long-21-12">Long et al. (2008), p. 21-12.</ref> | ||
== Fires in car parks and tunnels == | == Fires in car parks and tunnels == | ||
Parked cars can spread fire to their neighbours, which makes the [[Car park fire]] a design problem of its own. In the Scranton Fire Test of 1972, three cars with 38 litres of petrol each stood in an open multi-storey car park with exposed steel.<ref name="Holmes-20-220">Holmes (2008b), p. 20-220.</ref> The centre car was gutted 48 minutes after newspapers on its rear seat were lit, but the fire did not spread and the steel stayed far below critical temperatures. These results do not necessarily apply to enclosed or underground car parks. Full-scale tests on cars in car parks in the United Kingdom, the United States and Australia provide further data for determining fire severity.<ref name="IFEG-3.6-2">National Research Council of Canada et al. (2005), p. 3.6-2.</ref> | Parked cars can spread fire to their neighbours, which makes the [[Car park fire]] a design problem of its own. In the US Scranton Fire Test of 1972, three cars with 38 litres of petrol each stood in an open multi-storey car park with exposed steel.<ref name="Holmes-20-220">Holmes (2008b), p. 20-220.</ref> The centre car was gutted 48 minutes after newspapers on its rear seat were lit, but the fire did not spread and the steel stayed far below critical temperatures. These results do not necessarily apply to enclosed or underground car parks. Full-scale tests on cars in car parks in the United Kingdom, the United States and Australia provide further data for determining fire severity.<ref name="IFEG-3.6-2">National Research Council of Canada et al. (2005), p. 3.6-2.</ref> | ||
Recent experience is less reassuring. Fires in modern cars spread faster and release more heat, so a single car fire is more likely to become a long, intense fire involving 10 to 50 or more vehicles.<ref name="NIPV-11" /> A sprinkler or water mist system can confine a car fire to a small number of cars, although it cannot reach a burning battery pack.<ref name="NIPV-36">Van der Graaf et al. (2021/2023), pp. 36–37.</ref> | Recent experience is less reassuring. Fires in modern cars spread faster and release more heat, so a single car fire is more likely to become a long, intense fire involving 10 to 50 or more vehicles.<ref name="NIPV-11" /> A sprinkler or water mist system can confine a car fire to a small number of cars, although it cannot reach a burning battery pack.<ref name="NIPV-36">Van der Graaf et al. (2021/2023), pp. 36–37.</ref> As summarised in the 2008 handbook, US requirements generally called for sprinklers in enclosed garages below grade and in those over 23 m (75 ft) high.<ref name="Moore-20-169" /> | ||
In a [[Tunnel fire]], the vehicle fire load is unknown or inconsistent, so designers use typical design fires.<ref name="Bendelius-21-204" | In a [[Tunnel fire]], the vehicle fire load is unknown or inconsistent, so designers use typical design fires.<ref name="Bendelius-21-204" /> NFPA 502 (2008 edition), as summarised in the handbook, gives a peak of 5–10 MW for one passenger car and 10–20 MW for two to four cars. The peak may be reached within 10 minutes, and temperatures directly above the fire can reach 1,000 to 1,400 °C. Buses, heavy goods vehicles and tankers are given much larger design fires, from 20 MW up to 300 MW. | ||
== Response and suppression == | == Response and suppression == | ||
The handbook gives basic steps for any vehicle fire. The engine and all electrical systems are shut off, everyone is moved well away from the vehicle, preferably uphill and upwind, and the fire department is called.<ref name="Routhier-21-22">Routhier (2008), p. 21-22.</ref> A fire is fought only if this can be done without danger, with the extinguisher aimed at the base of the flames.<ref name="Routhier-21-23">Routhier (2008), p. 21-23.</ref> A burning flammable gas is left to burn until the leak is controlled, and a hood is opened carefully because of sudden flare-ups. | The handbook gives basic steps for any vehicle fire. The engine and all electrical systems are shut off, everyone is moved well away from the vehicle, preferably uphill and upwind, and the fire department is called.<ref name="Routhier-21-22">Routhier (2008), p. 21-22.</ref> A fire is fought only if this can be done without danger, with the extinguisher aimed at the base of the flames.<ref name="Routhier-21-23">Routhier (2008), p. 21-23.</ref> A burning flammable gas is left to burn until the leak is controlled, and a hood is opened carefully because of sudden flare-ups.<ref name="Routhier-21-23" /> The 2008 US handbook states that private cars, vans and light trucks did not have to carry an extinguisher.<ref name="Routhier-21-22" /> | ||
For the fire service, the tactics for an automobile fire are much the same in a city and in a rural area.<ref name="Klaene-13-4">Klaene and Sanders (2008), p. 13-4.</ref> For vehicles on gaseous fuels, the apparatus is placed upwind and the fuel is identified from its marking before the attack.<ref name="Rivkin-21-74">Rivkin (2008b), p. 21-74.</ref> Water streams can control fires of compressed natural gas or liquefied petroleum gas, but on a pool of liquefied natural gas they greatly speed up the boil-off. The NIPV report gives a rule of thumb for cooling capacity. A high-pressure jet of 125 litres per minute | For the fire service, the tactics for an automobile fire are much the same in a city and in a rural area.<ref name="Klaene-13-4">Klaene and Sanders (2008), p. 13-4.</ref> For vehicles on gaseous fuels, the apparatus is placed upwind and the fuel is identified from its marking before the attack.<ref name="Rivkin-21-74">Rivkin (2008b), p. 21-74.</ref> Water streams can control fires of compressed natural gas or liquefied petroleum gas, but on a pool of liquefied natural gas they greatly speed up the boil-off. The NIPV report gives a rule of thumb for cooling capacity. A high-pressure jet of 125 litres per minute is generally sufficient for fires up to 2.5 MW, and a low-pressure jet of 450 litres per minute is generally sufficient for fires up to 10 MW.<ref name="NIPV-45">Van der Graaf et al. (2021/2023), p. 45.</ref> For a rapid attack on a burning car near a car park entrance, the international assumption is two low-pressure jets. | ||
Prevention and early control remain hard in postcollision fires. To prevent deaths, the occupants must escape or the fire must be put out before conditions become untenable.<ref name="Long-21-11" /> Because fuel-fed fires can become untenable before the fire service arrives, on-board suppression systems are one of the leading mitigation strategies.<ref name="Long-21-12" /> One test series found, however, that such a system was highly unlikely to extinguish most engine compartment and underbody fires. In 2008, the handbook authors described research on postcollision fires as being in its infancy.<ref name="Long-21-13">Long et al. (2008), p. 21-13.</ref> | Prevention and early control remain hard in postcollision fires. To prevent deaths, the occupants must escape or the fire must be put out before conditions become untenable.<ref name="Long-21-11" /> Because fuel-fed fires can become untenable before the fire service arrives, on-board suppression systems are one of the leading mitigation strategies.<ref name="Long-21-12" /> One test series found, however, that such a system was highly unlikely to extinguish most engine compartment and underbody fires.<ref name="Long-21-12" /> In 2008, the handbook authors described research on postcollision fires as being in its infancy.<ref name="Long-21-13">Long et al. (2008), p. 21-13.</ref> | ||
== See also == | == See also == | ||
Revision as of 23:34, 7 November 2026
A motor vehicle fire is a fire in a self-propelled road vehicle, such as a passenger car, van, bus or truck. Like any fire it needs a flammable substance, an ignition source and oxygen; petrol and diesel vehicles carry fuel, while upholstery, wiring insulation and plastic trim can burn regardless of power source.[1] In the United States, vehicle fires made up 20.1% of reported fires and 13.5% of civilian fire deaths in 2000–2004, excluding the 11 September 2001 deaths.[2] In the cited US data, most highway vehicle fires started in the engine area, while fires following a collision caused a far larger share of the deaths.[3][4][5] Example values for a car are an energy content of 6,000 to 12,000 MJ and a peak heat release rate of 8.5 MW.[6][7] Car fires are used as design fires for indoor car parks and road tunnels.[8][9]
Definition and classification
Vehicle fire hazard depends on vehicle type, use, climate, age, condition and maintenance.[1] It also depends on the construction standards for the fuel and electrical systems and on the fuel itself: petrol (gasoline in US sources), diesel, propane, natural gas or alcohol. Besides the fuel, upholstery, insulating and sound-deadening materials, wiring insulation and plastic body parts can feed the fire. Cargo carried in or on the vehicle, particularly by trucks, may also be flammable.[1] Buses, trucks and tank vehicles are treated in Commercial vehicle fire, and vehicles running on gaseous and other alternative fuels in Alternative fuel vehicle.
Statistical systems draw the boundaries of the term in different ways. In the US National Fire Incident Reporting System (NFIRS), version 5.0, a vehicle burning inside a structure counts as a vehicle fire unless the structure itself becomes involved.[10] Once the building is involved, the incident becomes a structure fire, and the vehicle is recorded as mobile property. Analyses of passenger vehicle fires differ in whether pickups, buses, motorcycles and trailers are counted, so their estimates differ.[11]
Counting the dead is also difficult. After a collision, an autopsy may be needed to decide whether a person died from the fire or from injuries, and people who died immediately of trauma are not counted as fire deaths.[10] In the US Fatality Analysis Reporting System (FARS), only about one quarter of the deaths associated with passenger vehicle fires resulted from the fire itself.[5]
Fire statistics in the United States
The statistics below are US data, mostly from around 2000. Fire statistics show that vehicle fires accounted for 20.1% of reported fires and 13.5% of civilian deaths in 2000–2004; the death share excludes 11 September 2001.[2] They caused nearly three times as many fire deaths as all structures other than homes. The number of highway vehicle fires fell from 411,300 in 1980 to 281,600 in 2002, almost one third fewer.[12] The annual average for 1999–2002 was 269,900 fires, 380 civilian deaths and 1,310 civilian injuries.
About 32,000 occupants of passenger vehicles died each year in traffic crashes in the United States.[13] About 1.2% of these deaths, or 385 a year, were attributed to fires after a collision, and a further 40 a year to fires without a collision. Postcollision fires thus accounted for 90% of passenger vehicle fire deaths in 1999–2004.[5] In about half of the deaths from unintentional fires without a collision, the occupant was asleep or impaired by alcohol or other drugs.[5] Routhier reported approximately 6,200 collision-related highway vehicle fires a year.[1]
The risk has fallen over time. For cars and light trucks of model year 1978 and earlier, the risk of a fire death was 3.7 per million registered vehicles per year.[14] For model years 1996–2004 it was 1.8, and per billion vehicle miles travelled it dropped from 0.42 to 0.13, almost 70% lower. This happened while vehicles contained more plastics: 7.6% of the weight of highway vehicles in 2004 against 5.0% in 1978, and 117 kg in a typical passenger car.[13] Older vehicles burn more often, and the median age of US passenger cars rose by 50% to almost 9 years between 1980 and 2004.[15]
These numbers have known limits. NFIRS captures only one third to one half of US fire incidents, so analysts scale it up with the NFPA annual survey.[5] About half of all passenger vehicle fires in NFIRS have no factor contributing to ignition recorded. The NFPA/NFIRS estimate of passenger vehicle fire deaths is about 8% higher than the FARS estimate.[5]
Causes and areas of origin
Ignition sources in vehicles include electrical short circuits, sparks from the engine ignition system, hot exhaust parts and engine backfire.[1] Overheated tyres, brakes and wheel bearings, friction sparks from a collision or from metal scraping on the road, and careless smoking add to the list.[16] In NFIRS data for US highway vehicle fires in 1999–2002, mechanical failure or malfunction contributed to 48% of the fires but only 9% of the deaths.[4] Electrical failure contributed to 23% of the fires and 2% of the deaths. Collisions, knock-downs, run-overs and roll-overs contributed to only 3% of the fires but to 57% of the deaths.
The area of origin shows the same pattern. In 1999–2003, the engine area, running gear or wheel area was the origin of 65% of US highway vehicle fires and 39% of the deaths.[3] The operator or passenger area accounted for 17% of the fires and 20% of the deaths. Fires starting at the fuel tank or fuel line made up only 2% of the fires but 17% of the deaths. This corresponds to about 15 deaths per 1,000 fuel system fires, against about 1.4 per 1,000 for all highway vehicle fires.
Studies of postcollision fires show two main types: fuel-fed pool fires of petrol, and fires that start in the engine compartment.[5] Of the US postcollision passenger vehicle fire deaths in 1999–2004, 63% involved fires in which petrol was ignited first, and 48% involved fires that began in the engine area, running gear or wheel area.[14] In the United States in 1994–1998, fuel-fed fires made up 27% of highway vehicle fires but caused 56% of the vehicle fire deaths.[17] Routhier (2008) identified rear-end collisions as a fuel-tank concern because most US-built vehicles had their tanks at the rear.[18] The handbook’s separate review of postcollision fires reported that most fires in one crash sample followed front-end impacts and began in the engine compartment.[17]
Several other mechanisms recur. Diesel has a higher flashpoint than petrol, but diesel engines run hotter, so warm fuel leaking onto a hot surface can still ignite.[19] Catalytic converters can start wildland fires when cars are driven through dry grass, and overused brakes can overheat until they smoulder or burn. Vehicles are also the main fire risk at service stations: in 1994–1998, 62% of fires at US public service stations were classed as vehicle fires.[20]
Fire development and heat release rate
In full-scale tests after severe crash tests, the time to untenable conditions in the passenger compartment was strongly linked to the moment flames entered it.[17] Flames from an engine compartment fire entered through the failed windshield, the heating and air-conditioning vents or openings in the bulkhead. In the pool fire tests, flames entered through gaps around deformed doors or underbody seams, and conditions became untenable after 1.6 to 4.0 minutes. In pool fires, untenable conditions can thus arise much faster than emergency personnel can respond.[21] The power output of the initial pool fire is set by the size of the fuel pool rather than by the flammability of the vehicle materials.[17]
The interior adds its own fuel. Because the US interior materials test is lax, seating in cars is commonly easily ignitable and produces rapidly growing fires with a high heat release.[22] Major parts of newer vehicles are plastic, and these materials can cause severe fires with copious amounts of smoke.[23] A Dutch report on indoor car parks states that modern cars, with their high plastic content, have a greater fire load and a higher heat release rate than older steel models.[24]
The Heat release rate of single cars varies widely. In tests at the Fire Research Station (FRS), a 1982 Austin Maestro reached a peak of 8.5 MW and a 1986 Citroën BX a peak of 4.5 MW.[25] Three cars from the late 1970s tested at VTT each peaked at about 1.5–2.0 MW. The reason for this spread is not fully clear, but it is not the share of polymers in the cars. In the published curves, both FRS cars peaked roughly 15 minutes into the test.
A literature review summarised in a report of the Netherlands Institute for Public Safety (NIPV) found a typical peak of about 6 MW for cars with combustion engines.[26] The average times to reach the peak ranged from 6 to 35 minutes, and the total heat released was 3.3 to 10 GJ. This matches the order of the 6,000 to 12,000 MJ example for a car.[6] A typical car fire burns for just over half an hour, with a maximum of about 5 MW after about 10–15 minutes.[27] With petrol at about 32 MJ/litre, a full 50 litre tank holds about 1.6 GJ, or roughly 13–27% of that energy content.[26]
In fire tests on electric and conventional cars, similar temperatures of about 800 ± 100 °C were measured for 5 to 30 minutes.[28] Smoke from some plastic materials, such as the interior of a burning car, caused severe effects when only a small amount was inhaled.[29] Battery packs add hydrogen fluoride to the smoke, as described in Electric vehicle fire, but the plastic parts of any burning car already produce severely toxic smoke.[27][30]
Design fires and calculation
Indoor car park design uses a design fire: a heat release rate curve over time.[8] In New Zealand, Verification Method C/VM2 (second edition, 2025) prescribes a pre-flashover growth of 0.0117t² kW for car parks without stacking systems.[31] That car park design scenario grows to a peak of 20 MW, with a heat of combustion of 20 MJ/kg, a soot yield of 0.07 kg/kg and a radiative fraction of 0.35. In a computational fluid dynamics model the burning area follows from 500 to 1,000 kW/m², and in a zone model from 250 kW/m². The design fire load energy density for car parks is 400 MJ/m².[32]
The commentary to the first edition of C/VM2 explains why car parks get their own growth rate. Car parks are one of the few risk groups in which the fuel can be bounded and its layout is controlled.[33] A literature review showed that the early growth of car fires can be modelled as a medium t-squared fire. In the Netherlands, the standard NEN 6098 for smoke control in mechanically ventilated car parks uses a design curve based on a 1999 design fire by TNO.[34] In the underlying tests, the fire could spread to the neighbouring cars 10–15 minutes after the first car, depending on their spacing. The curve includes intervention by the fire brigade, and represents three cars burning 15 minutes after ignition.
In the t-squared model, the heat release rate grows with the square of the time since effective ignition. A growth coefficient sets how fast the fire grows, and the time to reach a given size follows by rearranging the equation. Integrating the curve over time gives the energy released so far, which can be compared with the energy content of a car.
| Symbol | Description | Unit |
|---|---|---|
| Heat release rate of the fire | kW | |
| Fire growth coefficient (0.0117 for car parks in C/VM2) | kW/s² | |
| Time since effective ignition | s | |
| Energy released between ignition and time t | kJ |
As a worked example, take the C/VM2 coefficient of 0.0117 kW/s² and the guide value of 8,500 kW.[31][7] The time to reach this peak is the square root of 8,500/0.0117, which is about 852 s, or 14 minutes. The same curve reaches 5 MW after about 650 s, in line with the 10–15 minutes reported for a typical car fire.[27] The energy released up to 852 s is 0.0117 × 852³/3 kJ, or about 2,400 MJ. That is 20–40% of the 6,000 to 12,000 MJ in a car, so much of the fuel is still left at the peak.[6] With the fast coefficient of 0.0469 kW/s² used for most buildings, the fire would reach 8.5 MW after about 425 s, half the time.[31]
These models have clear limits. According to the 2013 commentary, the growth curves ignore the incipient phase, so C/VM2 may slightly over-predict early growth.[33] Measured peaks from tests are widely spread, from 1.5 to 8.5 MW for single cars.[25] Design curves based on tests from the 1990s may also be less conservative for modern cars, which contain more plastics.[34] Fire load values also depend on their source and purpose: a Swiss survey from 1967–69 gave an average of 200 MJ/m² for a parking building, half the New Zealand design value.[35]
Regulation and vehicle design
In the United States, the National Highway Traffic Safety Administration sets Federal Motor Vehicle Safety Standards (FMVSS) for the manufacture and sale of new vehicles.[13] By 2008, only four fire-related standards had been issued for new vehicles, and none for vehicles in use.[3] FMVSS 301, issued in 1968, limits fuel leakage after a crash for cars, trucks and buses with a gross vehicle weight rating up to 4,536 kg (10,000 lb).[13][11] In the crash tests, leakage may not exceed 28 g (1 oz) from impact until the vehicle stops, 142 g (5 oz) in the next 5 minutes, or 28 g per minute for 25 minutes.[3]
FMVSS 302, issued in 1972, covers materials in the passenger compartment, such as seat cushions, headlining, trim panels and floor coverings.[3] A horizontal sample may not burn or spread a flame faster than 102 mm/min (4 in./min).[11][36] The standard was aimed at interior fires caused by matches and cigarettes, and one handbook author calls it remarkable for its laxness.[3][22] FMVSS 303 and 304 cover the fuel system and the containers of vehicles running on compressed natural gas.[11]
Research shows that better test results for a single material do not always make a car safer. For engine-compartment materials, a study found the cone calorimeter the most suitable bench-scale test.[21] In such tests, a fire-retarded heating and air-conditioning unit released about 5 kW/m², against more than 200 kW/m² for untreated polypropylene.[37] In full-scale burns of two otherwise identical crashed cars, however, the heat release rates and times to untenable conditions were essentially the same. The fire-retarded unit even produced higher levels of toxic gases. For this reason, the authors argue for a systems approach that weighs fire performance against crash protection, durability and toxicity.[38]
Fires in car parks and tunnels
Parked cars can spread fire to their neighbours, which makes the Car park fire a design problem of its own. In the US Scranton Fire Test of 1972, three cars with 38 litres of petrol each stood in an open multi-storey car park with exposed steel.[39] The centre car was gutted 48 minutes after newspapers on its rear seat were lit, but the fire did not spread and the steel stayed far below critical temperatures. These results do not necessarily apply to enclosed or underground car parks. Full-scale tests on cars in car parks in the United Kingdom, the United States and Australia provide further data for determining fire severity.[40]
Recent experience is less reassuring. Fires in modern cars spread faster and release more heat, so a single car fire is more likely to become a long, intense fire involving 10 to 50 or more vehicles.[24] A sprinkler or water mist system can confine a car fire to a small number of cars, although it cannot reach a burning battery pack.[41] As summarised in the 2008 handbook, US requirements generally called for sprinklers in enclosed garages below grade and in those over 23 m (75 ft) high.[23]
In a Tunnel fire, the vehicle fire load is unknown or inconsistent, so designers use typical design fires.[9] NFPA 502 (2008 edition), as summarised in the handbook, gives a peak of 5–10 MW for one passenger car and 10–20 MW for two to four cars. The peak may be reached within 10 minutes, and temperatures directly above the fire can reach 1,000 to 1,400 °C. Buses, heavy goods vehicles and tankers are given much larger design fires, from 20 MW up to 300 MW.
Response and suppression
The handbook gives basic steps for any vehicle fire. The engine and all electrical systems are shut off, everyone is moved well away from the vehicle, preferably uphill and upwind, and the fire department is called.[42] A fire is fought only if this can be done without danger, with the extinguisher aimed at the base of the flames.[43] A burning flammable gas is left to burn until the leak is controlled, and a hood is opened carefully because of sudden flare-ups.[43] The 2008 US handbook states that private cars, vans and light trucks did not have to carry an extinguisher.[42]
For the fire service, the tactics for an automobile fire are much the same in a city and in a rural area.[44] For vehicles on gaseous fuels, the apparatus is placed upwind and the fuel is identified from its marking before the attack.[45] Water streams can control fires of compressed natural gas or liquefied petroleum gas, but on a pool of liquefied natural gas they greatly speed up the boil-off. The NIPV report gives a rule of thumb for cooling capacity. A high-pressure jet of 125 litres per minute is generally sufficient for fires up to 2.5 MW, and a low-pressure jet of 450 litres per minute is generally sufficient for fires up to 10 MW.[46] For a rapid attack on a burning car near a car park entrance, the international assumption is two low-pressure jets.
Prevention and early control remain hard in postcollision fires. To prevent deaths, the occupants must escape or the fire must be put out before conditions become untenable.[37] Because fuel-fed fires can become untenable before the fire service arrives, on-board suppression systems are one of the leading mitigation strategies.[38] One test series found, however, that such a system was highly unlikely to extinguish most engine compartment and underbody fires.[38] In 2008, the handbook authors described research on postcollision fires as being in its infancy.[47]
See also
Notes
- ↑ 1.0 1.1 1.2 1.3 1.4 Routhier (2008), p. 21-15.
- ↑ 2.0 2.1 Hall and Cote (2008), p. 3-21.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Routhier (2008), p. 21-17.
- ↑ 4.0 4.1 Ahrens et al. (2008), p. 3-78.
- ↑ 5.0 5.1 5.2 5.3 5.4 5.5 5.6 Long et al. (2008), p. 21-6.
- ↑ 6.0 6.1 6.2 Van Rossum (2027), §4.4.
- ↑ 7.0 7.1 Van Rossum (2027), §4.5.
- ↑ 8.0 8.1 Van der Graaf et al. (2021/2023), p. 24.
- ↑ 9.0 9.1 Bendelius (2008), p. 21-204.
- ↑ 10.0 10.1 Ahrens and Stewart (2008), p. 3-49.
- ↑ 11.0 11.1 11.2 11.3 Long et al. (2008), p. 21-5.
- ↑ Routhier (2008), p. 21-16.
- ↑ 13.0 13.1 13.2 13.3 Long et al. (2008), p. 21-4.
- ↑ 14.0 14.1 Long et al. (2008), p. 21-7.
- ↑ Long et al. (2008), p. 21-3.
- ↑ Routhier (2008), pp. 21-15–21-16.
- ↑ 17.0 17.1 17.2 17.3 Long et al. (2008), p. 21-9.
- ↑ Routhier (2008), pp. 21-20–21-21.
- ↑ Routhier (2008), p. 21-21.
- ↑ Rivkin (2008a), p. 21-29.
- ↑ 21.0 21.1 Long et al. (2008), p. 21-10.
- ↑ 22.0 22.1 Babrauskas (2008b), p. 6-116.
- ↑ 23.0 23.1 J. Moore (2008), pp. 20-168–20-169.
- ↑ 24.0 24.1 Van der Graaf et al. (2021/2023), p. 11.
- ↑ 25.0 25.1 Babrauskas (2002b), p. 3-27.
- ↑ 26.0 26.1 Van der Graaf et al. (2021/2023), p. 25.
- ↑ 27.0 27.1 27.2 Van der Graaf et al. (2021/2023), p. 26.
- ↑ Van der Graaf et al. (2021/2023), p. 23.
- ↑ Purser (2002), p. 2-112.
- ↑ Van der Graaf et al. (2021/2023), p. 30.
- ↑ 31.0 31.1 31.2 Ministry of Business, Innovation and Employment (2025b), p. 20.
- ↑ Ministry of Business, Innovation and Employment (2025b), p. 22.
- ↑ 33.0 33.1 Ministry of Business, Innovation and Employment (2013), p. 55.
- ↑ 34.0 34.1 Van Rossum (2027), §8.6.
- ↑ National Research Council of Canada et al. (2005), pp. 3.4-2, 3.4-6.
- ↑ Routhier (2008), p. 21-18.
- ↑ 37.0 37.1 Long et al. (2008), p. 21-11.
- ↑ 38.0 38.1 38.2 Long et al. (2008), p. 21-12.
- ↑ Holmes (2008b), p. 20-220.
- ↑ National Research Council of Canada et al. (2005), p. 3.6-2.
- ↑ Van der Graaf et al. (2021/2023), pp. 36–37.
- ↑ 42.0 42.1 Routhier (2008), p. 21-22.
- ↑ 43.0 43.1 Routhier (2008), p. 21-23.
- ↑ Klaene and Sanders (2008), p. 13-4.
- ↑ Rivkin (2008b), p. 21-74.
- ↑ Van der Graaf et al. (2021/2023), p. 45.
- ↑ Long et al. (2008), p. 21-13.
References
- Ahrens, M., & Stewart, S. (2008). Fire data collection and databases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-43–3-59). National Fire Protection Association.
- Ahrens, M., Frazier, P., & Kelch, G. (2008). Use of fire incident data and statistics. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-61–3-92). National Fire Protection Association.
- Babrauskas, V. (2002b). Heat release rates. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 3-1–3-37). National Fire Protection Association; Society of Fire Protection Engineers.
- Babrauskas, V. (2008b). Upholstered furniture and mattresses. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-103–6-128). National Fire Protection Association.
- Bendelius, A. G. (2008). Road tunnels and bridges. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-187–21-212). National Fire Protection Association.
- Hall, J. R., Jr., & Cote, A. E. (2008). An overview of the fire problem and fire protection. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 3-3–3-30). National Fire Protection Association.
- Holmes, W. D. (2008b). Occupancies in special structures. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 20-217–20-226). National Fire Protection Association.
- Klaene, B. J., & Sanders, R. (2008). Fireground operations. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-3–13-11). National Fire Protection Association.
- Long, R. T., Jr., Colwell, J. D., Ray, R., Grossman, H. L., Thomas, B., & Strassburger, R. (2008). Passenger vehicle fires. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-3–21-14). National Fire Protection Association.
- Ministry of Business, Innovation and Employment. (2013). Commentary for Building Code clauses C1–C6 and Verification Method C/VM2.
- Ministry of Business, Innovation and Employment. (2025b). Verification Method C/VM2: Framework for fire safety design (2nd ed.).
- Moore, J. (2008). Storage occupancies. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 20-157–20-178). National Fire Protection Association.
- National Research Council of Canada, International Code Council, Department of Building and Housing, & Australian Building Codes Board. (2005). International fire engineering guidelines (2005 ed.). Australian Building Codes Board.
- Purser, D. A. (2002). Toxicity assessment of combustion products. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 2-83–2-171). National Fire Protection Association; Society of Fire Protection Engineers.
- Rivkin, C. H. (2008a). Automotive and marine service station operations. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-29–21-40). National Fire Protection Association.
- Rivkin, C. H. (2008b). Vehicle fueling using gaseous fuels. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-41–21-76). National Fire Protection Association.
- Routhier, B. (2008). Fire safety in commercial vehicles. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-15–21-27). National Fire Protection Association.
- Van der Graaf, J., Hessels, T., & Rosmuller, N. (2023). Fire safety of indoor car parks accommodating electrically powered vehicles. Nederlands Instituut Publieke Veiligheid. (Original work published 2021)
- Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.