Fact-check correction: Night/day ratio over all 11 rows of the sample is 1.7 (coal gas) to 3.6 (ethylene oxide), Table 13.8.7 |
Wiki review: corrected 1 error: content (Claude Opus 5.5) |
||
| Line 10: | Line 10: | ||
The guidebook serves the transport side of hazardous materials regulation. DOT regulated the transport of some 4000 hazardous materials, and transport classification uses nine internationally accepted hazard classes.<ref name="Wr-13-121">C. J. Wright (2008a), p. 13-121.</ref><ref name="Wr-13-118-119">C. J. Wright (2008a), pp. 13-118–13-119.</ref> Within DOT, Hildebrand and Noll name the Pipeline and Hazardous Materials Safety Administration as the agency responsible for the safe and secure movement of hazardous materials by all modes of transport.<ref name="HN-13-82">Hildebrand and Noll (2008), p. 13-82.</ref> | The guidebook serves the transport side of hazardous materials regulation. DOT regulated the transport of some 4000 hazardous materials, and transport classification uses nine internationally accepted hazard classes.<ref name="Wr-13-121">C. J. Wright (2008a), p. 13-121.</ref><ref name="Wr-13-118-119">C. J. Wright (2008a), pp. 13-118–13-119.</ref> Within DOT, Hildebrand and Noll name the Pipeline and Hazardous Materials Safety Administration as the agency responsible for the safe and secure movement of hazardous materials by all modes of transport.<ref name="HN-13-82">Hildebrand and Noll (2008), p. 13-82.</ref> | ||
The guidebook is one of several references used by [[hazardous materials response|hazardous materials responders]]. Wright stresses that no single printed source provides all the information needed, so more than one resource may have to be consulted.<ref name="Wr-13-127">C. J. Wright (2008a), p. 13-127.</ref> His cross-reference of common guides lists two primary resources, the ERG and the pocket guide to chemical hazards of the National Institute | The guidebook is one of several references used by [[hazardous materials response|hazardous materials responders]]. Wright stresses that no single printed source provides all the information needed, so more than one resource may have to be consulted.<ref name="Wr-13-127">C. J. Wright (2008a), p. 13-127.</ref> His cross-reference of common guides lists two primary resources, the ERG and the pocket guide to chemical hazards of the National Institute for Occupational Safety and Health (NIOSH). Seven other works are listed as secondary resources.<ref name="Wr-13-131" /> The secondary resources include guides of the Association of American Railroads, the guide to hazardous materials of the National Fire Protection Association (NFPA), a US Coast Guard manual and material safety data sheets (MSDSs).<ref name="Wr-13-130" /> | ||
== Contents == | == Contents == | ||
Latest revision as of 00:43, 16 November 2026
The Emergency Response Guidebook (ERG) is a reference book published by the U.S. Department of Transportation (DOT) that gives first responders emergency response procedures for transport incidents involving explosives and other hazardous materials.[1] According to the Fire Protection Handbook (20th edition, 2008), it is widely distributed and normally carried on all hazardous materials transport vehicles and by emergency responders such as fire and police departments.[1] The handbook cites the 2004 edition.[2]
Responders reach the right entry through a material's name or its four-digit identification number, shown on shipping papers and on many placards.[3][4] According to Wright's comparison of reference guides, it typically contains first aid, protective equipment, extinguishing agents and evacuation distances.[5] Its table of initial isolation and protective action distances is used to estimate the size of the area that a release may affect.[6] For a large chlorine spill, for example, the 2004 table gave an initial isolation distance of 275 m and a downwind protective action distance of 6.8 km at night.[7] In the United States, the use of the guidebook was one of the competencies required of responders at the lowest, awareness level of training.[8]
Publisher and purpose
The Emergency Response Guidebook is a DOT publication; the handbook's list of common reference guides names the Research and Special Programs Administration of DOT as its source.[9] Santis describes it as covering emergency response procedures for transportation incidents involving explosives or other hazardous materials.[1] It was sold in the bookstores of the US Government Printing Office and also offered in electronic form.[1] Both handbook chapters that cite it refer to the 2004 edition, ERG2004.[2][10]

The guidebook serves the transport side of hazardous materials regulation. DOT regulated the transport of some 4000 hazardous materials, and transport classification uses nine internationally accepted hazard classes.[11][12] Within DOT, Hildebrand and Noll name the Pipeline and Hazardous Materials Safety Administration as the agency responsible for the safe and secure movement of hazardous materials by all modes of transport.[13]
The guidebook is one of several references used by hazardous materials responders. Wright stresses that no single printed source provides all the information needed, so more than one resource may have to be consulted.[14] His cross-reference of common guides lists two primary resources, the ERG and the pocket guide to chemical hazards of the National Institute for Occupational Safety and Health (NIOSH). Seven other works are listed as secondary resources.[5] The secondary resources include guides of the Association of American Railroads, the guide to hazardous materials of the National Fire Protection Association (NFPA), a US Coast Guard manual and material safety data sheets (MSDSs).[9]
Contents
Wright's cross-reference table shows which kinds of information are typically found in each guide. For the ERG it marks eight items: the DOT identification number, what the material reacts with, route of entry, evacuation distances, first aid, personal protective equipment, decontamination and extinguishing agents.[5] As an illustration, these are 8 of the 39 items in the table, or about one-fifth. Physical properties such as boiling point, vapour pressure and flash point are not marked for the guidebook, nor are exposure limits such as the value immediately dangerous to life and health.[5] The table also does not mark the ERG for toxic products of combustion, a question of fire toxicity; it marks MSDSs and several secondary guides for that item.[5]
The response information is arranged in numbered guides, which responders refer to by guide number.[15] Wright notes that immediate decontamination guidelines are found under first aid on these numbered guide pages.[16] The guidebook also contains the table of initial isolation and protective action distances.[6]
The handbook takes two of its definitions of protective actions from the 2004 guidebook. Evacuation is to "move all people from the threatened area to a safer place".[17] In-place protection "means to direct people to quickly go inside a building and remain inside until the danger passes".[17] Wright adds that evacuation requires enough time for people to be warned, to get ready and to leave, and that in-place protection is used when evacuation would cause greater risk or cannot be carried out.[18]
Identifying the material
To use the guidebook, responders must first identify the material. Identification numbers are four-digit numbers assigned to a specific hazardous material or group of materials, used to cross-reference its name to hazard and response information.[3] On bulk packages such as cargo tanks, portable tanks and tank cars, they are displayed on an orange panel, in the centre of the placard or on a white square-on-point display.[3] On shipping papers the number is preceded by "UN" for domestic and international shipments or by "NA" for shipments considered hazardous only within North America.[3]
Placards and labels are the second clue. Placards of 273 mm by 273 mm are required on some bulk packages, and labels of 102 mm or smaller are found on some nonbulk packages.[4] They convey information by colour, symbol, hazard class or division number, and either the class wording or the four-digit identification number.[4] Shipping papers give the proper shipping name, hazard class, identification number and quantity, and include an emergency telephone number and response information for the commodity.[19]
Rail and road transport add their own documents. A train consist lists the position of every car and includes emergency response information for each hazardous material on the train.[20] For highway incidents, Routhier lists the placards with their four-digit numbers and the shipping papers among the information to obtain, and advises approaching the scene from upwind.[21] The same list warns that placarding and identification markings on a cargo tank may be incorrect or missing, and that shipping papers may be missing, incomplete or incorrect.[21]
Table of initial isolation and protective action distances
The table gives two distances for each listed material and for two sizes of release. Small spills are those from a small package or a small leak from a large package; large spills come from a large package or from many small packages.[7] For each case, responders first isolate the area in all directions to the stated distance, and then protect persons downwind up to a second distance.[7] The downwind distance is given separately for day and for night.[7] The handbook reproduces a sample of the 2004 table, part of which is shown below in metric units.[7]
| ID No. | Material | Small spills | Large spills | ||||
|---|---|---|---|---|---|---|---|
| Isolate in all directions (m) | Protect downwind, day (km) | Protect downwind, night (km) | Isolate in all directions (m) | Protect downwind, day (km) | Protect downwind, night (km) | ||
| 1005 | Ammonia, anhydrous | 30 | 0.2 | 0.2 | 60 | 0.5 | 1.1 |
| 1016 | Carbon monoxide | 30 | 0.2 | 0.2 | 125 | 0.6 | 1.8 |
| 1017 | Chlorine | 30 | 0.3 | 1.1 | 275 | 2.7 | 6.8 |
| 1026 | Cyanogen | 30 | 0.3 | 1.1 | 305 | 3.1 | 7.7 |
| 1040 | Ethylene oxide | 30 | 0.2 | 0.2 | 60 | 0.5 | 1.8 |
| 1050 | Hydrogen chloride, anhydrous | 30 | 0.2 | 0.6 | 185 | 1.6 | 4.3 |
| 1051 | AC (when used as a weapon) | 60 | 0.2 | 0.5 | 460 | 1.6 | 3.9 |
The sample shows how strongly the distances depend on the size of the release. For chlorine (ID 1017), the isolation distance is 30 m for a small spill and 275 m for a large spill.[7] The downwind protective action distance for a large spill is 2.7 km by day and 6.8 km by night.[7] The handbook prints each distance in feet or miles with a rounded metric value, for example 900 ft (275 m).[7] The handbook does not explain how the distances were derived.
As an illustration, for a large chlorine spill at night, responders would first keep people out of a circle of 275 m radius, an area of about 0.24 km². They would then protect people downwind for 6.8 km, about 25 times the isolation radius. In every row of the handbook's sample, the night distance for a large spill is larger than the day distance, by a factor of about 1.7 (coal gas) to 3.6 (ethylene oxide); for the seven rows in the table above the factor is 2.2 to 3.6 (own calculation from the metric values in the sample). Wright's protective actions for people in a threatened area are evacuation and in-place protection.[18]
Wright presents the table as one of several inputs to the analysis. The dimensions of the engulfed area can be taken from the guidebook table, from planning documents or from dispersion modelling programs, and wind speed and direction and topography must be considered.[6] On arrival, before the analysis is complete, personnel should stop at a safe location uphill, upwind and upstream.[22] Suggested minimum safe distances for this stage should be specified in the local emergency response plan or the organisation's standard operating procedures, because sufficient information to determine safe distances is not yet available.[22]
Use in response and training
In the United States, the Hazardous Waste Operations and Emergency Response rule of the Occupational Safety and Health Administration (OSHA) defines several levels of responder competence. At the awareness level, responders must understand their role in the local emergency operations plan, including site safety, security and control, and the use of the Emergency Response Guidebook.[8] Typical awareness-level personnel included police officers, plant security staff and some public works employees, who secure the site, recognise the materials and notify trained responders.[8]
Fire departments built the guidebook into their procedures. The National Institute of Standards and Technology (NIST) reproduced the 1994 hazardous materials plan of the Fire Department of the City of New York (FDNY). In that plan, first responders were to consult the guidebook and the department's own hazard action guides.[15] The incident commander implemented an initial plan of action as described in the guidebook and these guides.[23] The first and second arriving ladder companies looked up the guide and its isolation and evacuation recommendations, and confirmed the guide number, isolation distance and evacuation information with each other.[15]
The guidebook also supports later tasks. During planning, responders select a decontamination process, and the first-aid sections of the numbered guides are a source of immediate decontamination guidance.[16] Follow-up guidance comes from poison control centres, from the shipper or manufacturer through CHEMTREC and from the Agency for Toxic Substances and Disease Registry.[16] CHEMTREC can also contact the shipper and set up a teleconference with technical specialists.[14]
Tank cars, cargo tanks and BLEVE
Many of the materials in the guidebook travel in bulk in rail tank cars and highway cargo tanks. In 2005, 85 percent of rail shipments of hazardous materials moved in tank cars.[20] C. J. Wright advises that a tank car exposed to radiant heat from a fire, particularly direct flame impingement, should be approached cautiously. If the contents absorb too much heat, vapour pressure can build up and cause the pressure relief device to operate or the tank to rupture.[24] Routhier lists the potential for a BLEVE among the hazards to fire fighters at cargo tanks carrying hazardous materials.[21]
A BLEVE (boiling liquid expanding vapour explosion) is the rapid boiling and expansion of liquefied gas after its container fails; the container may break into two or more pieces.[25] Most such failures result from fire exposure, although corrosion or impact can also cause them.[26] Lemoff stresses that a BLEVE is what happens after the container fails, not how it fails.[26] For unreactive liquefied flammable gases, pieces can be propelled up to about 0.8 km, missiles can kill as far as 244 m from larger containers, and fatal burns can occur up to 76 m away.[27] In fire tests on LP-gas rail tank cars, a BLEVE occurred after 93 minutes for an insulated tank and after 25 minutes for an uninsulated one.[27]
These values come from the handbook's chapter on gases, not from the guidebook. Besides the guidebook distances, Wright's analysis includes a prediction of how each container and its contents will behave, based on the worst possible case.[28] Thermal protection on some tank cars is designed to keep tank metal temperatures below 427 °C for 100 minutes in a pool fire or 30 minutes in a torch fire.[29]
Limits and common misconceptions
The guidebook does not cover every hazardous material. Whitford notes that most pesticides that responders will encounter are neither required to be placarded nor found in the Emergency Response Guidebook.[30] It also does not provide all the information needed: in Wright's table it lacks physical properties, exposure limits and toxic combustion products, which other references supply.[5]
Identification may fail before the guidebook can be used. Transport vehicles and freight containers could carry up to 1000 lb (454 kg) of certain hazardous materials without a placard, and limited-quantity shipments did not require placards.[4] On rail cars, placards and markings may not be visible because of the car's orientation, and it may not be prudent to approach close enough to read them; aided vision such as binoculars may help.[20] Information found must also be checked against what is seen, because shipping papers and observations may disagree.[14]
The distances are initial guidance for transport incidents. Wright treats them as one of several ways to estimate the engulfed area, to be refined with planning documents, dispersion models, weather and topography as the analysis continues.[6] The values quoted in this article are from the 2004 edition reproduced in the 2008 handbook and describe US practice of that time.
See also
- Chemical protective clothing
- Decontamination
- Incident command system
- Pre-incident planning
- Weapons of mass destruction
Notes
- ↑ 1.0 1.1 1.2 1.3 Santis (2008), p. 6-251.
- ↑ 2.0 2.1 C. J. Wright (2008a), p. 13-144.
- ↑ 3.0 3.1 3.2 3.3 C. J. Wright (2008a), p. 13-122.
- ↑ 4.0 4.1 4.2 4.3 C. J. Wright (2008a), p. 13-124.
- ↑ 5.0 5.1 5.2 5.3 5.4 5.5 C. J. Wright (2008a), p. 13-131.
- ↑ 6.0 6.1 6.2 6.3 C. J. Wright (2008a), p. 13-134.
- ↑ 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 C. J. Wright (2008a), p. 13-136.
- ↑ 8.0 8.1 8.2 Hildebrand and Noll (2008), p. 13-88.
- ↑ 9.0 9.1 C. J. Wright (2008a), p. 13-130.
- ↑ Santis (2008), p. 6-256.
- ↑ C. J. Wright (2008a), p. 13-121.
- ↑ C. J. Wright (2008a), pp. 13-118–13-119.
- ↑ Hildebrand and Noll (2008), p. 13-82.
- ↑ 14.0 14.1 14.2 C. J. Wright (2008a), p. 13-127.
- ↑ 15.0 15.1 15.2 Lawson and Vettori (2005), Appendix A, FDNY hazardous materials plan, §4.2.
- ↑ 16.0 16.1 16.2 C. J. Wright (2008a), p. 13-141.
- ↑ 17.0 17.1 U.S. Department of Transportation (2004), as cited in C. J. Wright (2008a), p. 13-142.
- ↑ 18.0 18.1 C. J. Wright (2008a), p. 13-142.
- ↑ C. J. Wright (2008a), pp. 13-125–13-126.
- ↑ 20.0 20.1 20.2 C. J. Wright (2008b), p. 21-112.
- ↑ 21.0 21.1 21.2 Routhier (2008), p. 21-24.
- ↑ 22.0 22.1 C. J. Wright (2008a), p. 13-126.
- ↑ Lawson and Vettori (2005), Appendix A, FDNY hazardous materials plan, §4.1.
- ↑ C. J. Wright (2008b), p. 21-110.
- ↑ Lemoff (2008), pp. 6-170–6-171.
- ↑ 26.0 26.1 Lemoff (2008), p. 6-171.
- ↑ 27.0 27.1 Lemoff (2008), p. 6-172.
- ↑ C. J. Wright (2008a), p. 13-132.
- ↑ C. J. Wright (2008b), p. 21-125.
- ↑ Whitford (2008), p. 6-240.
References
- Hildebrand, M. S., & Noll, G. G. (2008). Public fire protection and hazmat management. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-81–13-98). National Fire Protection Association.
- Lawson, J. R., & Vettori, R. L. (2005). The emergency response operations (NIST NCSTAR 1-8). National Institute of Standards and Technology.
- Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
- Routhier, B. (2008). Fire safety in commercial vehicles. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-15–21-27). National Fire Protection Association.
- Santis, L. D. (2008). Explosives and blasting agents. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-247–6-256). National Fire Protection Association.
- Whitford, F. (2008). Pesticides in the workplace. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-233–6-245). National Fire Protection Association.
- Wright, C. J. (2008a). Managing the response to hazardous material incidents. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 13-117–13-144). National Fire Protection Association.
- Wright, C. J. (2008b). Rail transportation systems. In A. E. Cote, C. C. Grant, J. R. Hall, Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-109–21-134). National Fire Protection Association.