New FSE wiki article: Fire pump (written by GPT-6) |
Wiki review: corrected 18 errors: citation (18) (Claude Opus 5.5) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
'''Fire pump''' is a pump that adds hydraulic energy to water used for fire protection. <ref name="T_4-67_4-69">Titus (2002), ch. 4-2, pp. 4-67–4-69.</ref><ref name="H_15_6_15-85">Cote (2008), ch. 15.6, | '''Fire pump''' is a pump that adds hydraulic energy to water used for fire protection. <ref name="T_4-67_4-69">Titus (2002), ch. 4-2, pp. 4-67–4-69.</ref><ref name="H_15_6_15-85">Cote (2008), ch. 15.6, p. 15-85.</ref> Its useful duty depends on the water source, suction conditions and the resistance of the connected installation. A rated flow and pressure describe one operating point. They do not establish the water reserve, automatic starting reliability or performance throughout the operating range. <ref name="H_15_6_15-89_15-99">Cote (2008), ch. 15.6, pp. 15-89–15-99.</ref> | ||
The engineering assessment combines the source, pump, driver, controls and delivery route. Static pressure is only one observation within that chain. Flowing performance, maximum pressure and the capacity to continue for the required duration answer different questions. Records of the installed arrangement and suitable tests connect the calculated duty to the equipment that must operate during a fire. <ref name="H_15_6_15-89_15-99" /><ref name="H_16_11_16-220">Cote (2008), ch. 16.11, | The engineering assessment combines the source, pump, driver, controls and delivery route. Static pressure is only one observation within that chain. Flowing performance, maximum pressure and the capacity to continue for the required duration answer different questions. Records of the installed arrangement and suitable tests connect the calculated duty to the equipment that must operate during a fire. <ref name="H_15_6_15-89_15-99" /><ref name="H_16_11_16-220">Cote (2008), ch. 16.11, p. 16-220.</ref> Starting tests and flowing tests exercise different functions. <ref name="H_16_11_16-220" /> | ||
== Duty and installation == | == Duty and installation == | ||
A fire pump forms part of the [[Fire water supply|fire water supply]] serving a [[Sprinkler system|sprinkler system]] or other firefighting outlets. Installations supplying [[Dry and wet risers|dry and wet risers]] can have demands and pressure limits different from those of ceiling sprinklers. The pump is therefore selected against the complete duty, including the upstream source and downstream distribution. Its nameplate does not define the entire protection arrangement. <ref name="H_15_6_15-85_15-93_15-94">Cote (2008), ch. 15.6, pp. 15-85,15-93–15-94.</ref><ref name="H_16_10_16-195_16-198">Cote (2008), ch. 16.10, pp. 16-195,16-198.</ref> | A fire pump forms part of the [[Fire water supply|fire water supply]] serving a [[Sprinkler system|sprinkler system]] or other firefighting outlets. Installations supplying [[Dry and wet risers|dry and wet risers]] can have demands and pressure limits different from those of ceiling sprinklers. The pump is therefore selected against the complete duty, including the upstream source and downstream distribution. Its nameplate does not define the entire protection arrangement. <ref name="H_15_6_15-85_15-93_15-94">Cote (2008), ch. 15.6, pp. 15-85, 15-93–15-94.</ref><ref name="H_16_10_16-195_16-198">Cote (2008), ch. 16.10, pp. 16-195, 16-198.</ref> | ||
[[File:fse-fire-pump-v1.svg|thumb|upright=1.5|alt=Fire pump: functional relationships. Measurement and water paths are distinct.|Fire pump: functional relationships. Schematic explanation; dimensions are not installation instructions.]] | |||
Horizontal centrifugal and vertical turbine arrangements differ in how they receive water | Horizontal centrifugal and vertical turbine arrangements differ in how they receive water; the handbook describes submerged turbine stages for sources below the installation's upper pump equipment. [[Net positive suction head]] remains part of the hydraulic assessment. The [[Fire pump performance curve|fire pump performance curve]] must be interpreted with the actual suction condition, rather than assuming that every source can support the rated discharge. <ref name="H_15_6_15-91_15-95">Cote (2008), ch. 15.6, pp. 15-91–15-95.</ref> | ||
A [[Fire pump controller|fire pump controller]] connects the demand signal to driver operation | A [[Fire pump controller|fire pump controller]] connects the demand signal to driver operation; a [[Diesel fire pump driver|diesel fire pump driver]] provides one alternative to an electric motor, with its own fuel, starting and cooling dependencies. These components are parts of the water-delivery chain rather than independent guarantees of performance. Testing the installed combination provides evidence about that chain under the conditions exercised. <ref name="H_15_6_15-98_15-99">Cote (2008), ch. 15.6, pp. 15-98–15-99.</ref><ref name="H_15_7_15-114_15-115">Cote (2008), ch. 15.7, pp. 15-114–15-115.</ref><ref name="H_16_11_16-220" /> | ||
== Pump operation and selection == | == Pump operation and selection == | ||
A centrifugal pump transfers shaft energy to water through a rotating impeller | A centrifugal pump transfers shaft energy to water through a rotating impeller; its performance varies with flow, speed and pump geometry. The selected duty belongs on a curve showing this relationship, rather than being defined by a single pressure reading. The complete operating point also depends on the resistance and supply conditions of the connected installation. <ref name="H_15_6_15-85_15-89_15-92">Cote (2008), ch. 15.6, pp. 15-85, 15-89–15-92.</ref><ref name="T_4-67_4-69" /> | ||
[[File:fse-fire-pump-v2.svg|thumb|upright=1.5|alt=Pump and installed system. Measurement and water paths are distinct.|Pump and installed system. Schematic explanation; dimensions are not installation instructions.]] | |||
The pump head is the energy added across the pump | The pump head is the energy added across the pump; discharge pressure alone is not that quantity when suction pressure, elevation or velocity differ between measuring points. Horizontal pumps and vertical turbine arrangements require appropriate references for their respective configurations. A test comparison can be misleading if the water level or suction reference has changed without being recorded. <ref name="H_15_6_15-89_15-90">Cote (2008), ch. 15.6, pp. 15-89–15-90.</ref> | ||
A centrifugal pump normally develops its greatest head near shutoff and less head at higher flows | A centrifugal pump normally develops its greatest head near shutoff and less head at higher flows; the closed-outlet condition therefore needs assessment for maximum system pressure. At the other end of the operating range, the remaining head must meet the required discharge pressure after losses. Driver capability and suction conditions can constrain operation even where the plotted head appears adequate. <ref name="H_15_6_15-91_15-98">Cote (2008), ch. 15.6, pp. 15-91–15-98.</ref><ref name="T_4-68_4-69">Titus (2002), ch. 4-2, pp. 4-68–4-69.</ref> | ||
The handbook's account of United States NFPA 20 practice describes a rated point, a high-flow point and a shutoff limit. It reports at least 65% of rated head at 150% of rated flow, with shutoff head no greater than 140%. These are historical criteria reported in the 2008 handbook. They are not a substitute for a selected pump's actual curve or a statement of a current adopted standard. <ref name="H_15_6_15-92">Cote (2008), ch. 15.6, | The handbook's account of United States NFPA 20 practice describes a rated point, a high-flow point and a shutoff limit. It reports at least 65% of rated head at 150% of rated flow, with shutoff head no greater than 140%. These are historical criteria reported in the 2008 handbook. They are not a substitute for a selected pump's actual curve or a statement of a current adopted standard. <ref name="H_15_6_15-92">Cote (2008), ch. 15.6, p. 15-92.</ref> | ||
Connecting pumps in series adds their heads at a common flow | Connecting pumps in series adds their heads at a common flow; connecting them in parallel combines flow at a common head. Neither arrangement automatically doubles delivery through the installed network, because the operating intersection changes. Shared suction piping and power dependencies also remain part of the installation rather than disappearing through duplication. <ref name="T_4-70">Titus (2002), ch. 4-2, p. 4-70.</ref><ref name="H_15_6_15-93_15-95">Cote (2008), ch. 15.6, pp. 15-93–15-95.</ref> | ||
The water source must be assessed alongside the pump | The water source must be assessed alongside the pump; a booster can overcome insufficient pressure but cannot create an absent water reserve. A powerful driver cannot correct an obstructed intake or inadequate suction conditions. Selection therefore brings together the source, suction route, performance curve, driver, controls and downstream demand. <ref name="H_15_6_15-91_15-99">Cote (2008), ch. 15.6, pp. 15-91–15-99.</ref><ref name="T_4-68_4-69" /> | ||
== Suction conditions and cavitation == | == Suction conditions and cavitation == | ||
Water approaching an impeller must retain enough absolute pressure to avoid excessive vapour formation | Water approaching an impeller must retain enough absolute pressure to avoid excessive vapour formation; pressure falls as flow accelerates through the inlet region. If local pressure reaches the water's vapour pressure, bubbles can form and subsequently collapse in higher-pressure regions. This cavitation can produce noise, vibration, loss of performance and material damage. <ref name="H_15_6_15-91">Cote (2008), ch. 15.6, p. 15-91.</ref><ref name="T_4-68">Titus (2002), ch. 4-2, p. 4-68.</ref> | ||
[[File:fse-fire-pump-v3.svg|thumb|upright=1.5|alt=Available suction head. Measurement and water paths are distinct.|Available suction head. Schematic explanation; dimensions are not installation instructions.]] | |||
Available net positive suction head describes the installation's suction energy above vapour-pressure head | Available net positive suction head describes the installation's suction energy above vapour-pressure head; required net positive suction head describes a pump characteristic supplied by the manufacturer for stated operating conditions. The two quantities must be compared at the relevant flow and speed. They are not two alternative names for a suction gauge reading. <ref name="H_15_6_15-91_15-92">Cote (2008), ch. 15.6, pp. 15-91–15-92.</ref><ref name="T_4-68" /> | ||
For a large open reservoir, the following form separates atmospheric pressure, water level and suction losses | For a large open reservoir, the following form separates atmospheric pressure, water level and suction losses; the reservoir surface velocity is treated as negligible. A positive elevation difference means that the water surface is above the pump reference. A lower surface contributes a negative term. <ref name="T_4-68" /> | ||
<math display="block">NPSH_a=\frac{p_a-p_v}{\rho g}+z_s-z_p-h_s</math> | <math display="block">NPSH_a=\frac{p_a-p_v}{\rho g}+z_s-z_p-h_s</math> | ||
| Line 44: | Line 47: | ||
|} | |} | ||
The lowest usable tank level can be more demanding than the initial full condition | The lowest usable tank level can be more demanding than the initial full condition; a greater flow increases suction-pipe loss and can also increase the pump's required suction head. Warmer water increases vapour pressure, while atmospheric pressure varies with elevation. These effects explain why a universal maximum suction lift cannot represent every installation. <ref name="H_15_6_15-91_15-95" /><ref name="T_4-68" /> | ||
The handbook illustrates a pump requiring approximately 3.05 m of suction head at 7,570 L/min and 5.49 m at 11,400 L/min. These are converted values from one illustrative manufacturer's-style curve, not general acceptance limits. Their significance is the changing requirement as flow rises. The appropriate comparison uses the actual pump data and the available head under the corresponding supply condition. <ref name="H_15_6_15-91" /> | The handbook illustrates a pump requiring approximately 3.05 m of suction head at 7,570 L/min and 5.49 m at 11,400 L/min. These are converted values from one illustrative manufacturer's-style curve, not general acceptance limits. Their significance is the changing requirement as flow rises. The appropriate comparison uses the actual pump data and the available head under the corresponding supply condition. <ref name="H_15_6_15-91" /> | ||
== Driver power and operating range == | == Driver power and operating range == | ||
Hydraulic power is the rate at which energy is transferred to water | Hydraulic power is the rate at which energy is transferred to water; shaft power must also cover the pump's losses, so it exceeds hydraulic power whenever efficiency is below unity. The required driver rating depends on the relevant operating range. Selecting only from the nominal duty point can miss a greater shaft-power demand elsewhere on the curve. <ref name="H_15_6_15-97_15-98">Cote (2008), ch. 15.6, pp. 15-97–15-98.</ref> | ||
For flow expressed in litres per minute and differential pressure in kilopascals, the following equation gives shaft power in kilowatts | For flow expressed in litres per minute and differential pressure in kilopascals, the following equation gives shaft power in kilowatts; the conversion factor incorporates both the litre and minute conversions. Efficiency is a fraction, not a percentage inserted as a whole number. The equation assumes that the stated pressure represents the pump's added hydraulic energy consistently. <ref name="H_15_6_15-98">Cote (2008), ch. 15.6, p. 15-98.</ref><ref name="T_4-68" /> | ||
<math display="block">P_s=\frac{Q\,\Delta p}{60000\eta}</math> | <math display="block">P_s=\frac{Q\,\Delta p}{60000\eta}</math> | ||
| Line 69: | Line 72: | ||
The handbook gives an SI example based on a pump rated at 4,000 L/min and 700 kPa. It evaluates a higher-flow condition of 6,400 L/min at 385 kPa, with efficiency assumed to be 0.65. Substitution gives 63.2 kW of shaft power. This is a calculation at the stated illustrative condition, not a complete driver selection or an additional operating allowance. <ref name="H_15_6_15-98" /> | The handbook gives an SI example based on a pump rated at 4,000 L/min and 700 kPa. It evaluates a higher-flow condition of 6,400 L/min at 385 kPa, with efficiency assumed to be 0.65. Substitution gives 63.2 kW of shaft power. This is a calculation at the stated illustrative condition, not a complete driver selection or an additional operating allowance. <ref name="H_15_6_15-98" /> | ||
An electric installation must provide both starting and running capability | An electric installation must provide both starting and running capability; the controller, conductors and power arrangement therefore have duties beyond the motor's nominal output. A diesel installation avoids reliance on normal external electrical power for running, but needs fuel, starting capability, cooling and ventilation. Independence from one supply does not remove these other dependencies. <ref name="H_15_7_15-106_15-113_15-115">Cote (2008), ch. 15.7, pp. 15-106, 15-113–15-115.</ref><ref name="H_15_6_15-98_15-99" /> | ||
Changes in speed also change pump behaviour | Changes in speed also change pump behaviour; for the same impeller under affinity-law assumptions, flow scales with speed, head with its square and power with its cube. A small speed change can therefore alter power more strongly than flow. These relationships support interpretation, while the selected equipment's permitted operating envelope remains a separate constraint. <ref name="H_15_6_15-91_15-92" /> | ||
== Starting, control and supervision == | == Starting, control and supervision == | ||
Automatic starting connects a developing demand to pump operation without waiting for personnel at the pump | Automatic starting connects a developing demand to pump operation without waiting for personnel at the pump; a pressure-sensing arrangement is one means of detecting that demand. Its usefulness depends on the sensing connection, pressure settings and available power or engine-starting system. A running pump indication alone does not demonstrate that sufficient water reaches the protected area. <ref name="H_15_7_15-114_15-115_15-132_15-134">Cote (2008), ch. 15.7, pp. 15-114–15-115, 15-132–15-134.</ref><ref name="H_16_11_16-220" /> | ||
A pressure-maintenance pump serves a different purpose | A pressure-maintenance pump serves a different purpose; it replenishes small losses and limits repeated starts of the main fire pump. The pressure settings of both pumps need coordinated interpretation with the supply and pump curve. A pressure-maintenance arrangement that masks fire demand or produces unsuitable pressure transitions undermines the intended sequence. <ref name="H_15_4_15-64">Cote (2008), ch. 15.4, p. 15-64.</ref><ref name="H_15_7_15-132_15-134">Cote (2008), ch. 15.7, pp. 15-132–15-134.</ref> | ||
Fire-pump motor control differs from ordinary machinery protection because continuing water delivery during a fire is a central design objective | Fire-pump motor control differs from ordinary machinery protection because continuing water delivery during a fire is a central design objective; the handbook describes a deliberately different response to some overload conditions. This does not mean that electrical fault protection is absent. Short-circuit capability, power switching and the controller's equipment ratings remain separate design concerns. <ref name="H_15_7_15-106_15-113_15-115_15-133">Cote (2008), ch. 15.7, pp. 15-106, 15-113–15-115, 15-133.</ref> | ||
Diesel controls distinguish warning conditions from those requiring shutdown | Diesel controls distinguish warning conditions from those requiring shutdown; the handbook discusses low oil pressure, high temperature and starting failure as alarm conditions, while overspeed has a shutdown function. These distinctions avoid treating every engine warning as an instruction to stop firefighting water. Their implementation belongs to the specified fire-pump driver and controller arrangement. <ref name="H_15_6_15-99">Cote (2008), ch. 15.6, p. 15-99.</ref> | ||
Supervision communicates an abnormal state so that it can be addressed | Supervision communicates an abnormal state so that it can be addressed; it does not physically restore an isolated supply, replenish a tank or remove a pipe obstruction. An alarm path also introduces receiving, interpretation and response functions. The system assessment therefore includes what is monitored, where the signal goes and what operational condition it actually represents. <ref name="H_14_4_14-40_14-43">Cote (2008), ch. 14.4, pp. 14-40–14-43.</ref><ref name="H_16_11_16-212">Cote (2008), ch. 16.11, p. 16-212.</ref> | ||
Testing must exercise the function under examination | Testing must exercise the function under examination; a start initiated by a simulated pressure decrease checks a different chain from a full-flow test. Alarm bypass testing checks a different chain from actual discharge through a remote connection. Recorded results need enough context to distinguish a successful component operation from successful delivery by the complete system. <ref name="H_16_11_16-210_16-211_16-220">Cote (2008), ch. 16.11, pp. 16-210–16-211, 16-220.</ref> | ||
== Flow, pressure and duration == | == Flow, pressure and duration == | ||
A fire water supply has several necessary characteristics: adequate flow, sufficient pressure at that flow, an appropriate duration and availability when needed | A fire water supply has several necessary characteristics: adequate flow, sufficient pressure at that flow, an appropriate duration and availability when needed; these characteristics cannot replace one another. A large reservoir may have insufficient delivery capacity, while a high-pressure connection may offer too little sustained flow. The required combination depends on the fire protection demand being assessed. <ref name="H_15_2_15-23_15-24">Cote (2008), ch. 15.2, pp. 15-23–15-24.</ref><ref name="H_15_4_15-63_15-67">Cote (2008), ch. 15.4, pp. 15-63–15-67.</ref> | ||
Demand must identify which outlets operate together | Demand must identify which outlets operate together; sprinkler calculations assemble the flows of individual operating sprinklers and include other applicable demands under the selected design basis. Municipal fire-flow planning addresses a different question and may include wider firefighting activity. Treating every quoted fire-flow value as a sprinkler demand obscures these differences. <ref name="H_15_2_15-23_15-29">Cote (2008), ch. 15.2, pp. 15-23–15-29.</ref><ref name="F_4-74_4-81">Fleming (2002), ch. 4-3, pp. 4-74–4-81.</ref> | ||
The supply location also matters | The supply location also matters; a pressure measured in a street main is not automatically available at a building riser. Connecting pipework, backflow assemblies and changes in elevation affect the transfer. The assessment follows the supply through these elements to the same reference point used for the calculated demand. <ref name="H_15_4_15-63_15-65">Cote (2008), ch. 15.4, pp. 15-63–15-65.</ref><ref name="F_4-81_4-83">Fleming (2002), ch. 4-3, pp. 4-81–4-83.</ref> | ||
Storage introduces a time dimension that a pressure-flow curve alone does not show | Storage introduces a time dimension that a pressure-flow curve alone does not show; usable water is the quantity that the outlet or pump can actually draw while meeting its operating conditions. Water below the effective intake, or reserved for another purpose, cannot simply be counted as fire reserve. Replenishment contributes only through an identified source and a delivery arrangement that remains available. <ref name="H_15_1_15-3_15-5">Cote (2008), ch. 15.1, pp. 15-3–15-5.</ref><ref name="F_4-83_4-84">Fleming (2002), ch. 4-3, pp. 4-83–4-84.</ref> | ||
A constant-flow volume calculation multiplies flow by duration. In the following form, flow is in litres per minute and usable volume is in cubic metres. The factor converts litres to cubic metres. <ref name="F_4-83_4-84" /> | A constant-flow volume calculation multiplies flow by duration. In the following form, flow is in litres per minute and usable volume is in cubic metres. The factor converts litres to cubic metres. <ref name="F_4-83_4-84" /> | ||
| Line 109: | Line 112: | ||
A worked example separates usable water from gross capacity. Using Fleming's example of 530 L/min for 30 minutes gives 15,900 L, or 15.9 m³, of usable water. This arithmetic does not select a design duration or establish the gross tank volume. The example is a historical worked calculation, with tank configuration and unavailable volume assessed separately. <ref name="F_4-83_4-84" /> | A worked example separates usable water from gross capacity. Using Fleming's example of 530 L/min for 30 minutes gives 15,900 L, or 15.9 m³, of usable water. This arithmetic does not select a design duration or establish the gross tank volume. The example is a historical worked calculation, with tank configuration and unavailable volume assessed separately. <ref name="F_4-83_4-84" /> | ||
Public supplies can change with domestic use, industrial demand, maintenance and seasonal conditions | Public supplies can change with domestic use, industrial demand, maintenance and seasonal conditions; tank levels and pump operation can change during a fire as well. The design record therefore needs the conditions represented by the available supply, including relevant adverse conditions. A favourable isolated reading does not establish availability throughout the required incident duration. <ref name="H_15_2_15-23_15-24" /><ref name="H_15_4_15-63_15-64">Cote (2008), ch. 15.4, pp. 15-63–15-64.</ref> | ||
== Measuring the available supply == | == Measuring the available supply == | ||
A supply test relates an observed discharge to the pressure remaining elsewhere in the connected system | A supply test relates an observed discharge to the pressure remaining elsewhere in the connected system; the initial static reading describes the condition before the test discharge begins. The residual reading describes the pressure while the measured discharge is flowing. Both belong to the same test arrangement and must be recorded with its location and operating conditions. <ref name="F_4-81">Fleming (2002), ch. 4-3, p. 4-81.</ref><ref name="H_15_3_15-46_15-47">Cote (2008), ch. 15.3, pp. 15-46–15-47.</ref> | ||
The flowing outlet and the pressure observation have different functions | The flowing outlet and the pressure observation have different functions; a pitot measurement in an appropriate free jet supports an estimate of outlet flow. A gauge at the residual hydrant measures pressure in the distribution system during that discharge. Substituting jet pressure for residual system pressure confuses two different physical quantities. <ref name="H_15_3_15-46_15-47" /><ref name="F_4-81" /> | ||
The discharge estimate depends on outlet geometry and the coefficient representing its losses | The discharge estimate depends on outlet geometry and the coefficient representing its losses; a disturbed or nonuniform jet makes a single point reading less representative. Probe alignment and position also influence the measurement. For some discharge devices, a calibrated nozzle or suitable flowmeter provides a more appropriate method than applying a simple pitot relation. <ref name="H_15_3_15-46_15-47" /> | ||
Test results describe a network state, rather than an unlimited promise of future supply | Test results describe a network state, rather than an unlimited promise of future supply; domestic demand, pumps, source levels and closed valves can change that state. The pressure reference must also be carried correctly to the building calculation. A test performed at a different elevation or upstream of additional resistance needs hydraulic interpretation before comparison with system demand. <ref name="H_15_2_15-23_15-24" /><ref name="F_4-81_4-83" /> | ||
A main-drain test provides a different kind of evidence | A main-drain test provides a different kind of evidence; the handbook uses changes from previous static and flowing readings to identify possible deterioration or obstruction. This is useful for detecting change, but it does not independently establish the full sprinkler demand. Test opening, supply state and instrument condition affect whether successive observations are comparable. <ref name="H_16_11_16-210_16-211">Cote (2008), ch. 16.11, pp. 16-210–16-211.</ref> | ||
Pump testing likewise separates a start test from a flow-performance test | Pump testing likewise separates a start test from a flow-performance test; running successfully without substantial discharge demonstrates some operating functions but does not establish the entire pump curve. Flowing observations across the relevant operating range give evidence about delivery capability. The handbook describes retaining records so that deterioration and the ability to meet system demand can be assessed. <ref name="H_16_11_16-220" /> | ||
== See also == | == See also == | ||
Latest revision as of 01:32, 16 November 2026
Fire pump is a pump that adds hydraulic energy to water used for fire protection. [1][2] Its useful duty depends on the water source, suction conditions and the resistance of the connected installation. A rated flow and pressure describe one operating point. They do not establish the water reserve, automatic starting reliability or performance throughout the operating range. [3]
The engineering assessment combines the source, pump, driver, controls and delivery route. Static pressure is only one observation within that chain. Flowing performance, maximum pressure and the capacity to continue for the required duration answer different questions. Records of the installed arrangement and suitable tests connect the calculated duty to the equipment that must operate during a fire. [3][4] Starting tests and flowing tests exercise different functions. [4]
Duty and installation
A fire pump forms part of the fire water supply serving a sprinkler system or other firefighting outlets. Installations supplying dry and wet risers can have demands and pressure limits different from those of ceiling sprinklers. The pump is therefore selected against the complete duty, including the upstream source and downstream distribution. Its nameplate does not define the entire protection arrangement. [5][6]
Horizontal centrifugal and vertical turbine arrangements differ in how they receive water; the handbook describes submerged turbine stages for sources below the installation's upper pump equipment. Net positive suction head remains part of the hydraulic assessment. The fire pump performance curve must be interpreted with the actual suction condition, rather than assuming that every source can support the rated discharge. [7]
A fire pump controller connects the demand signal to driver operation; a diesel fire pump driver provides one alternative to an electric motor, with its own fuel, starting and cooling dependencies. These components are parts of the water-delivery chain rather than independent guarantees of performance. Testing the installed combination provides evidence about that chain under the conditions exercised. [8][9][4]
Pump operation and selection
A centrifugal pump transfers shaft energy to water through a rotating impeller; its performance varies with flow, speed and pump geometry. The selected duty belongs on a curve showing this relationship, rather than being defined by a single pressure reading. The complete operating point also depends on the resistance and supply conditions of the connected installation. [10][1]
The pump head is the energy added across the pump; discharge pressure alone is not that quantity when suction pressure, elevation or velocity differ between measuring points. Horizontal pumps and vertical turbine arrangements require appropriate references for their respective configurations. A test comparison can be misleading if the water level or suction reference has changed without being recorded. [11]
A centrifugal pump normally develops its greatest head near shutoff and less head at higher flows; the closed-outlet condition therefore needs assessment for maximum system pressure. At the other end of the operating range, the remaining head must meet the required discharge pressure after losses. Driver capability and suction conditions can constrain operation even where the plotted head appears adequate. [12][13]
The handbook's account of United States NFPA 20 practice describes a rated point, a high-flow point and a shutoff limit. It reports at least 65% of rated head at 150% of rated flow, with shutoff head no greater than 140%. These are historical criteria reported in the 2008 handbook. They are not a substitute for a selected pump's actual curve or a statement of a current adopted standard. [14]
Connecting pumps in series adds their heads at a common flow; connecting them in parallel combines flow at a common head. Neither arrangement automatically doubles delivery through the installed network, because the operating intersection changes. Shared suction piping and power dependencies also remain part of the installation rather than disappearing through duplication. [15][16]
The water source must be assessed alongside the pump; a booster can overcome insufficient pressure but cannot create an absent water reserve. A powerful driver cannot correct an obstructed intake or inadequate suction conditions. Selection therefore brings together the source, suction route, performance curve, driver, controls and downstream demand. [17][13]
Suction conditions and cavitation
Water approaching an impeller must retain enough absolute pressure to avoid excessive vapour formation; pressure falls as flow accelerates through the inlet region. If local pressure reaches the water's vapour pressure, bubbles can form and subsequently collapse in higher-pressure regions. This cavitation can produce noise, vibration, loss of performance and material damage. [18][19]
Available net positive suction head describes the installation's suction energy above vapour-pressure head; required net positive suction head describes a pump characteristic supplied by the manufacturer for stated operating conditions. The two quantities must be compared at the relevant flow and speed. They are not two alternative names for a suction gauge reading. [20][19]
For a large open reservoir, the following form separates atmospheric pressure, water level and suction losses; the reservoir surface velocity is treated as negligible. A positive elevation difference means that the water surface is above the pump reference. A lower surface contributes a negative term. [19]
| Symbol | Description | Unit |
|---|---|---|
| Available net positive suction head | m | |
| Absolute atmospheric and vapour pressures | Pa | |
| Water density and gravitational acceleration | kg/m³; m/s² | |
| Surface elevation, pump elevation and suction loss | m |
The lowest usable tank level can be more demanding than the initial full condition; a greater flow increases suction-pipe loss and can also increase the pump's required suction head. Warmer water increases vapour pressure, while atmospheric pressure varies with elevation. These effects explain why a universal maximum suction lift cannot represent every installation. [7][19]
The handbook illustrates a pump requiring approximately 3.05 m of suction head at 7,570 L/min and 5.49 m at 11,400 L/min. These are converted values from one illustrative manufacturer's-style curve, not general acceptance limits. Their significance is the changing requirement as flow rises. The appropriate comparison uses the actual pump data and the available head under the corresponding supply condition. [18]
Driver power and operating range
Hydraulic power is the rate at which energy is transferred to water; shaft power must also cover the pump's losses, so it exceeds hydraulic power whenever efficiency is below unity. The required driver rating depends on the relevant operating range. Selecting only from the nominal duty point can miss a greater shaft-power demand elsewhere on the curve. [21]
For flow expressed in litres per minute and differential pressure in kilopascals, the following equation gives shaft power in kilowatts; the conversion factor incorporates both the litre and minute conversions. Efficiency is a fraction, not a percentage inserted as a whole number. The equation assumes that the stated pressure represents the pump's added hydraulic energy consistently. [22][19]
| Symbol | Description | Unit |
|---|---|---|
| Required shaft power | kW | |
| Pump flow | L/min | |
| Equivalent differential pressure | kPa | |
| Pump efficiency | dimensionless |
The handbook gives an SI example based on a pump rated at 4,000 L/min and 700 kPa. It evaluates a higher-flow condition of 6,400 L/min at 385 kPa, with efficiency assumed to be 0.65. Substitution gives 63.2 kW of shaft power. This is a calculation at the stated illustrative condition, not a complete driver selection or an additional operating allowance. [22]
An electric installation must provide both starting and running capability; the controller, conductors and power arrangement therefore have duties beyond the motor's nominal output. A diesel installation avoids reliance on normal external electrical power for running, but needs fuel, starting capability, cooling and ventilation. Independence from one supply does not remove these other dependencies. [23][8]
Changes in speed also change pump behaviour; for the same impeller under affinity-law assumptions, flow scales with speed, head with its square and power with its cube. A small speed change can therefore alter power more strongly than flow. These relationships support interpretation, while the selected equipment's permitted operating envelope remains a separate constraint. [20]
Starting, control and supervision
Automatic starting connects a developing demand to pump operation without waiting for personnel at the pump; a pressure-sensing arrangement is one means of detecting that demand. Its usefulness depends on the sensing connection, pressure settings and available power or engine-starting system. A running pump indication alone does not demonstrate that sufficient water reaches the protected area. [24][4]
A pressure-maintenance pump serves a different purpose; it replenishes small losses and limits repeated starts of the main fire pump. The pressure settings of both pumps need coordinated interpretation with the supply and pump curve. A pressure-maintenance arrangement that masks fire demand or produces unsuitable pressure transitions undermines the intended sequence. [25][26]
Fire-pump motor control differs from ordinary machinery protection because continuing water delivery during a fire is a central design objective; the handbook describes a deliberately different response to some overload conditions. This does not mean that electrical fault protection is absent. Short-circuit capability, power switching and the controller's equipment ratings remain separate design concerns. [27]
Diesel controls distinguish warning conditions from those requiring shutdown; the handbook discusses low oil pressure, high temperature and starting failure as alarm conditions, while overspeed has a shutdown function. These distinctions avoid treating every engine warning as an instruction to stop firefighting water. Their implementation belongs to the specified fire-pump driver and controller arrangement. [28]
Supervision communicates an abnormal state so that it can be addressed; it does not physically restore an isolated supply, replenish a tank or remove a pipe obstruction. An alarm path also introduces receiving, interpretation and response functions. The system assessment therefore includes what is monitored, where the signal goes and what operational condition it actually represents. [29][30]
Testing must exercise the function under examination; a start initiated by a simulated pressure decrease checks a different chain from a full-flow test. Alarm bypass testing checks a different chain from actual discharge through a remote connection. Recorded results need enough context to distinguish a successful component operation from successful delivery by the complete system. [31]
Flow, pressure and duration
A fire water supply has several necessary characteristics: adequate flow, sufficient pressure at that flow, an appropriate duration and availability when needed; these characteristics cannot replace one another. A large reservoir may have insufficient delivery capacity, while a high-pressure connection may offer too little sustained flow. The required combination depends on the fire protection demand being assessed. [32][33]
Demand must identify which outlets operate together; sprinkler calculations assemble the flows of individual operating sprinklers and include other applicable demands under the selected design basis. Municipal fire-flow planning addresses a different question and may include wider firefighting activity. Treating every quoted fire-flow value as a sprinkler demand obscures these differences. [34][35]
The supply location also matters; a pressure measured in a street main is not automatically available at a building riser. Connecting pipework, backflow assemblies and changes in elevation affect the transfer. The assessment follows the supply through these elements to the same reference point used for the calculated demand. [36][37]
Storage introduces a time dimension that a pressure-flow curve alone does not show; usable water is the quantity that the outlet or pump can actually draw while meeting its operating conditions. Water below the effective intake, or reserved for another purpose, cannot simply be counted as fire reserve. Replenishment contributes only through an identified source and a delivery arrangement that remains available. [38][39]
A constant-flow volume calculation multiplies flow by duration. In the following form, flow is in litres per minute and usable volume is in cubic metres. The factor converts litres to cubic metres. [39]
| Symbol | Description | Unit |
|---|---|---|
| Usable water volume | m³ | |
| Constant discharge and duration | L/min; min |
A worked example separates usable water from gross capacity. Using Fleming's example of 530 L/min for 30 minutes gives 15,900 L, or 15.9 m³, of usable water. This arithmetic does not select a design duration or establish the gross tank volume. The example is a historical worked calculation, with tank configuration and unavailable volume assessed separately. [39]
Public supplies can change with domestic use, industrial demand, maintenance and seasonal conditions; tank levels and pump operation can change during a fire as well. The design record therefore needs the conditions represented by the available supply, including relevant adverse conditions. A favourable isolated reading does not establish availability throughout the required incident duration. [32][40]
Measuring the available supply
A supply test relates an observed discharge to the pressure remaining elsewhere in the connected system; the initial static reading describes the condition before the test discharge begins. The residual reading describes the pressure while the measured discharge is flowing. Both belong to the same test arrangement and must be recorded with its location and operating conditions. [41][42]
The flowing outlet and the pressure observation have different functions; a pitot measurement in an appropriate free jet supports an estimate of outlet flow. A gauge at the residual hydrant measures pressure in the distribution system during that discharge. Substituting jet pressure for residual system pressure confuses two different physical quantities. [42][41]
The discharge estimate depends on outlet geometry and the coefficient representing its losses; a disturbed or nonuniform jet makes a single point reading less representative. Probe alignment and position also influence the measurement. For some discharge devices, a calibrated nozzle or suitable flowmeter provides a more appropriate method than applying a simple pitot relation. [42]
Test results describe a network state, rather than an unlimited promise of future supply; domestic demand, pumps, source levels and closed valves can change that state. The pressure reference must also be carried correctly to the building calculation. A test performed at a different elevation or upstream of additional resistance needs hydraulic interpretation before comparison with system demand. [32][37]
A main-drain test provides a different kind of evidence; the handbook uses changes from previous static and flowing readings to identify possible deterioration or obstruction. This is useful for detecting change, but it does not independently establish the full sprinkler demand. Test opening, supply state and instrument condition affect whether successive observations are comparable. [43]
Pump testing likewise separates a start test from a flow-performance test; running successfully without substantial discharge demonstrates some operating functions but does not establish the entire pump curve. Flowing observations across the relevant operating range give evidence about delivery capability. The handbook describes retaining records so that deterioration and the ability to meet system demand can be assessed. [4]
See also
Notes
- ↑ 1.0 1.1 Titus (2002), ch. 4-2, pp. 4-67–4-69.
- ↑ Cote (2008), ch. 15.6, p. 15-85.
- ↑ 3.0 3.1 Cote (2008), ch. 15.6, pp. 15-89–15-99.
- ↑ 4.0 4.1 4.2 4.3 4.4 Cote (2008), ch. 16.11, p. 16-220.
- ↑ Cote (2008), ch. 15.6, pp. 15-85, 15-93–15-94.
- ↑ Cote (2008), ch. 16.10, pp. 16-195, 16-198.
- ↑ 7.0 7.1 Cote (2008), ch. 15.6, pp. 15-91–15-95.
- ↑ 8.0 8.1 Cote (2008), ch. 15.6, pp. 15-98–15-99.
- ↑ Cote (2008), ch. 15.7, pp. 15-114–15-115.
- ↑ Cote (2008), ch. 15.6, pp. 15-85, 15-89–15-92.
- ↑ Cote (2008), ch. 15.6, pp. 15-89–15-90.
- ↑ Cote (2008), ch. 15.6, pp. 15-91–15-98.
- ↑ 13.0 13.1 Titus (2002), ch. 4-2, pp. 4-68–4-69.
- ↑ Cote (2008), ch. 15.6, p. 15-92.
- ↑ Titus (2002), ch. 4-2, p. 4-70.
- ↑ Cote (2008), ch. 15.6, pp. 15-93–15-95.
- ↑ Cote (2008), ch. 15.6, pp. 15-91–15-99.
- ↑ 18.0 18.1 Cote (2008), ch. 15.6, p. 15-91.
- ↑ 19.0 19.1 19.2 19.3 19.4 Titus (2002), ch. 4-2, p. 4-68.
- ↑ 20.0 20.1 Cote (2008), ch. 15.6, pp. 15-91–15-92.
- ↑ Cote (2008), ch. 15.6, pp. 15-97–15-98.
- ↑ 22.0 22.1 Cote (2008), ch. 15.6, p. 15-98.
- ↑ Cote (2008), ch. 15.7, pp. 15-106, 15-113–15-115.
- ↑ Cote (2008), ch. 15.7, pp. 15-114–15-115, 15-132–15-134.
- ↑ Cote (2008), ch. 15.4, p. 15-64.
- ↑ Cote (2008), ch. 15.7, pp. 15-132–15-134.
- ↑ Cote (2008), ch. 15.7, pp. 15-106, 15-113–15-115, 15-133.
- ↑ Cote (2008), ch. 15.6, p. 15-99.
- ↑ Cote (2008), ch. 14.4, pp. 14-40–14-43.
- ↑ Cote (2008), ch. 16.11, p. 16-212.
- ↑ Cote (2008), ch. 16.11, pp. 16-210–16-211, 16-220.
- ↑ 32.0 32.1 32.2 Cote (2008), ch. 15.2, pp. 15-23–15-24.
- ↑ Cote (2008), ch. 15.4, pp. 15-63–15-67.
- ↑ Cote (2008), ch. 15.2, pp. 15-23–15-29.
- ↑ Fleming (2002), ch. 4-3, pp. 4-74–4-81.
- ↑ Cote (2008), ch. 15.4, pp. 15-63–15-65.
- ↑ 37.0 37.1 Fleming (2002), ch. 4-3, pp. 4-81–4-83.
- ↑ Cote (2008), ch. 15.1, pp. 15-3–15-5.
- ↑ 39.0 39.1 39.2 Fleming (2002), ch. 4-3, pp. 4-83–4-84.
- ↑ Cote (2008), ch. 15.4, pp. 15-63–15-64.
- ↑ 41.0 41.1 Fleming (2002), ch. 4-3, p. 4-81.
- ↑ 42.0 42.1 42.2 Cote (2008), ch. 15.3, pp. 15-46–15-47.
- ↑ Cote (2008), ch. 16.11, pp. 16-210–16-211.
References
- Cote, A. E. (Ed.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
- Fleming, R. P. (2002). Automatic sprinkler system calculations. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-72–4-87). National Fire Protection Association.
- Titus, J. J. (2002). Hydraulics. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-44–4-71). National Fire Protection Association.