New FSE wiki article: NFPA 92 (written by GPT-6) |
Add SVG figures fse-nfpa-92-v1.svg, fse-nfpa-92-v2.svg, fse-nfpa-92-v3.svg (list-6 visual plan) |
||
| (2 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
'''[[NFPA]] 92''' is the NFPA standard identified as ''Standard for [[Smoke control|Smoke Control]] Systems'' in the Australian Building Codes Board's 2020 fire-engineering data sheets. Those sheets cite its 2018 edition as a source of design-fire information. The engineering subject is the control of smoke movement, described in the SFPE Handbook through airflow, pressure differences and smoke-management methods.<ref name="ABCB-NFPA92">Australian Building Codes Board (2020), Data Sheet B1, pp. 11, 23.</ref><ref name="Klote-4-274–4-279">Klote (2002), pp. 4-274–4-279.</ref> | '''[[NFPA]] 92''' is the National Fire Protection Association (NFPA) standard identified as ''Standard for [[Smoke control|Smoke Control]] Systems'' in the Australian Building Codes Board's 2020 fire-engineering data sheets. Those sheets cite its 2018 edition as a source of design-fire information. The engineering subject is the control of smoke movement, described in the Society of Fire Protection Engineers (SFPE) Handbook through airflow, pressure differences and smoke-management methods.<ref name="ABCB-NFPA92">Australian Building Codes Board (2020), Data Sheet B1, pp. 11, 23.</ref><ref name="Klote-4-274–4-279">Klote (2002), pp. 4-274–4-279.</ref> | ||
The 2008 NFPA Fire Protection Handbook discusses two earlier documents: NFPA 92A for systems using barriers and pressure differences, and NFPA 92B for malls, atria and large spaces. That account provides the historical framework used here. Edition-specific requirements remain separate from the physical principles and design examples explained in the handbooks.<ref name="NFPA-§18.3,pp.18-43,18-55">Cote et al. (2008), §18.3, pp. 18-43, 18-55.</ref> | The 2008 NFPA Fire Protection Handbook discusses two earlier documents: NFPA 92A for systems using barriers and pressure differences, and NFPA 92B for malls, atria and large spaces. That account provides the historical framework used here. Edition-specific requirements remain separate from the physical principles and design examples explained in the handbooks.<ref name="NFPA-§18.3,pp.18-43,18-55">Cote et al. (2008), §18.3, pp. 18-43, 18-55.</ref> | ||
| Line 7: | Line 7: | ||
== Document context and the scope of an assessment == | == Document context and the scope of an assessment == | ||
NFPA guidance is cited by both the NFPA Fire Protection Handbook and the SFPE Handbook. The 2008 NFPA account associates NFPA 92A with pressurised stairs and zones separated by barriers. It associates NFPA 92B with large-volume spaces where a smoke layer develops above occupied levels | NFPA guidance is cited by both the NFPA Fire Protection Handbook and the SFPE Handbook. The 2008 NFPA account associates NFPA 92A with pressurised stairs and zones separated by barriers. It associates NFPA 92B with large-volume spaces where a smoke layer develops above occupied levels; these are related objectives, but their geometries and governing flows differ.<ref name="NFPA-§18.3,p.18-43">Cote et al. (2008), §18.3, p. 18-43.</ref><ref name="Klote-4-278–4-279">Klote (2002), pp. 4-278–4-279.</ref> | ||
[[File:fse-nfpa-92-v1.svg|thumb|upright=1.5|alt=NFPA 92: document context and the scope of an assessment, showing the relationships described in the text.|Document context and the scope of an assessment in the assessment of NFPA 92.]] | |||
The later Australian data sheets cite the 2018 NFPA 92 title when discussing fire-growth information. A citation to that edition establishes the source being referenced; it does not make every older handbook example a clause of the later standard. A design assessment consequently identifies the governing edition and retains the separate origins of its input data and calculation methods.<ref name="ABCB-NFPA92" /><ref name="NFPA-§18.3,p.18-43" /> | The later Australian data sheets cite the 2018 NFPA 92 title when discussing fire-growth information. A citation to that edition establishes the source being referenced; it does not make every older handbook example a clause of the later standard. A design assessment consequently identifies the governing edition and retains the separate origins of its input data and calculation methods.<ref name="ABCB-NFPA92" /><ref name="NFPA-§18.3,p.18-43" /> | ||
| Line 13: | Line 14: | ||
Smoke control starts with an objective. Protecting a stair against smoke infiltration differs from maintaining an upper smoke layer in a large hall. Removing residual smoke after a fire is another operation. Klote explains that dilution in the fire space cannot substitute for the pressure and airflow conditions needed to control smoke movement.<ref name="Klote-4-278–4-281">Klote (2002), pp. 4-278–4-281.</ref> | Smoke control starts with an objective. Protecting a stair against smoke infiltration differs from maintaining an upper smoke layer in a large hall. Removing residual smoke after a fire is another operation. Klote explains that dilution in the fire space cannot substitute for the pressure and airflow conditions needed to control smoke movement.<ref name="Klote-4-278–4-281">Klote (2002), pp. 4-278–4-281.</ref> | ||
The expected fire determines heat and smoke production, while the geometry determines entrainment and movement | The expected fire determines heat and smoke production, while the geometry determines entrainment and movement; the Australian data sheets describe characteristic growth rates and sensitivity to their selection. Those rates are inputs to an assessment rather than predictions that every fire follows an identical curve. The chosen scenario and period of interest remain attached to the result.<ref name="ABCB-NFPA92" /> | ||
The evidence also distinguishes equipment availability from adequacy for the selected fire | The evidence also distinguishes equipment availability from adequacy for the selected fire; a fan can run as intended while its capacity is insufficient for the assumed smoke production. Conversely, a suitable design can fail to operate because a control or power dependency is unavailable. The Australian data sheets separate these performance questions when discussing smoke-control effectiveness.<ref name="ABCB-effectiveness">Australian Building Codes Board (2020), Data Sheet C4, pp. 129–132.</ref> | ||
== Pressure systems and their physical basis == | == Pressure systems and their physical basis == | ||
Pressure drives airflow through gaps in a boundary. Klote describes the flow using an effective leakage area and a coefficient representing the opening geometry. For most paths other than extremely narrow cracks, a square-root pressure relationship is a useful approximation. The required fan flow consequently depends on the openings as well as the selected pressure difference.<ref name="Klote-4-280–4-282">Klote (2002), pp. 4-280–4-282.</ref> | Pressure drives airflow through gaps in a boundary. Klote describes the flow using an effective leakage area and a coefficient representing the opening geometry. For most paths other than extremely narrow cracks, a square-root pressure relationship is a useful approximation. The required fan flow consequently depends on the openings as well as the selected pressure difference.<ref name="Klote-4-280–4-282">Klote (2002), pp. 4-280–4-282.</ref> | ||
[[File:fse-nfpa-92-v2.svg|thumb|upright=1.5|alt=NFPA 92: pressure systems and their physical basis, showing the relationships described in the text.|Pressure systems and their physical basis in the assessment of NFPA 92.]] | |||
<math display="block">\dot V=C A\sqrt{\frac{2\Delta P}{\rho}}</math> | <math display="block">\dot V=C A\sqrt{\frac{2\Delta P}{\rho}}</math> | ||
| Line 37: | Line 39: | ||
|} | |} | ||
Klote's example uses a leakage area of 0.01 m². With a flow coefficient of 0.65 and air density of 1.2 kg/m³, a pressure difference of 2.5 Pa gives approximately 0.013 m³/s. Increasing the pressure difference to 75 Pa gives approximately 0.073 m³/s | Klote's example uses a leakage area of 0.01 m². With a flow coefficient of 0.65 and air density of 1.2 kg/m³, a pressure difference of 2.5 Pa gives approximately 0.013 m³/s. Increasing the pressure difference to 75 Pa gives approximately 0.073 m³/s; these are calculations for the stated closed-door leakage, not for an open doorway.<ref name="Klote-4-280–4-281">Klote (2002), pp. 4-280–4-281.</ref> | ||
<math display="block">\dot V=0.65(0.01)\sqrt{\frac{2(75)}{1.2}}\approx0.073\ \mathrm{m^3/s}</math> | <math display="block">\dot V=0.65(0.01)\sqrt{\frac{2(75)}{1.2}}\approx0.073\ \mathrm{m^3/s}</math> | ||
| Line 47: | Line 49: | ||
== Equipment states and demonstrated performance == | == Equipment states and demonstrated performance == | ||
A [[Smoke damper|smoke damper]], fan and initiating detector contribute to a sequence that changes the building's airflows. The NFPA handbook describes the practical difficulty of integrating fire alarm controls with ventilation equipment | A [[Smoke damper|smoke damper]], fan and initiating detector contribute to a sequence that changes the building's airflows. The NFPA handbook describes the practical difficulty of integrating fire alarm controls with ventilation equipment; the intended state of every controlled path must follow the identified fire condition. Testing one device alone cannot demonstrate that the whole sequence is correct.<ref name="NFPA-§14.4,p.14-47">Cote et al. (2008), §14.4, p. 14-47.</ref> | ||
The complete control sequence requires an operational check as well as a component inspection. The NFPA handbook describes interfaces between fire alarms and building ventilation systems, often installed by different trades. Correctly operating individual components does not establish that their combined sequence is correct | The complete control sequence requires an operational check as well as a component inspection. The NFPA handbook describes interfaces between fire alarms and building ventilation systems, often installed by different trades. Correctly operating individual components does not establish that their combined sequence is correct; the initiating signal, damper positions and fan operation must describe the same intended fire condition.<ref name="NFPA-§14.4,p.14-47" /> | ||
The Australian Building Codes Board's 2020 data sheets distinguish installation checks from tests of system performance in its required operating modes. They describe defect correction followed by retesting. These activities connect the design assumptions to the installed arrangement. A completed drawing or equipment label cannot supply the results of those operational tests.<ref name="ABCB-test">Australian Building Codes Board (2020), Data Sheet C4, pp. 130–131.</ref> | The Australian Building Codes Board's 2020 data sheets distinguish installation checks from tests of system performance in its required operating modes. They describe defect correction followed by retesting. These activities connect the design assumptions to the installed arrangement. A completed drawing or equipment label cannot supply the results of those operational tests.<ref name="ABCB-test">Australian Building Codes Board (2020), Data Sheet C4, pp. 130–131.</ref> | ||
| Line 63: | Line 65: | ||
The large volume can initially moderate the hazard. Air mixed into the plume reduces the concentration of combustion products and lowers the smoke temperature. However, dilution also increases the quantity of gas delivered to the layer. A benefit in concentration therefore accompanies an increased smoke-handling demand.<ref name="atriumsmokec_Milke-293">Milke (2002), pp. 4-292–4-293.</ref> | The large volume can initially moderate the hazard. Air mixed into the plume reduces the concentration of combustion products and lowers the smoke temperature. However, dilution also increases the quantity of gas delivered to the layer. A benefit in concentration therefore accompanies an increased smoke-handling demand.<ref name="atriumsmokec_Milke-293">Milke (2002), pp. 4-292–4-293.</ref> | ||
Life-safety assessment considers several properties of the smoke environment. These include layer-interface height, visibility, temperature and the concentrations of harmful gases. The layer height describes whether an occupied level becomes immersed in smoke | Life-safety assessment considers several properties of the smoke environment. These include layer-interface height, visibility, temperature and the concentrations of harmful gases. The layer height describes whether an occupied level becomes immersed in smoke; it does not, by itself, describe the severity of every possible exposure within that layer.<ref name="atriumsmokec_Milke-293" /> | ||
Reduced visibility can slow movement and increase disorientation. Milke also describes the potential for trips and falls where occupants cannot see obstructions or balcony edges. Longer evacuation then extends the period of exposure to smoke. A low predicted temperature does not remove these visibility-related effects.<ref name="atriumsmokec_Milke-293" /> | Reduced visibility can slow movement and increase disorientation. Milke also describes the potential for trips and falls where occupants cannot see obstructions or balcony edges. Longer evacuation then extends the period of exposure to smoke. A low predicted temperature does not remove these visibility-related effects.<ref name="atriumsmokec_Milke-293" /> | ||
| Line 75: | Line 77: | ||
A fire in a shop or another communicating space can produce a balcony spill plume. Smoke first rises to an intermediate ceiling, travels beneath it and then spills around an edge. Its subsequent rise into the atrium has a different geometry from a plume rising directly above a floor-level fire. The width and route of the spill become relevant inputs.<ref name="atriumsmokec_Milke-301">Milke (2002), pp. 4-301–4-302.</ref> | A fire in a shop or another communicating space can produce a balcony spill plume. Smoke first rises to an intermediate ceiling, travels beneath it and then spills around an edge. Its subsequent rise into the atrium has a different geometry from a plume rising directly above a floor-level fire. The width and route of the spill become relevant inputs.<ref name="atriumsmokec_Milke-301">Milke (2002), pp. 4-301–4-302.</ref> | ||
An adjoining-room scenario can involve several stages of mixing before smoke reaches the upper layer; modelling only a fire in the open atrium can omit those stages. Milke therefore distinguishes a balcony spill plume from a plume rising directly above a fire in the open volume. The assessment includes the actual connections between the room of origin and the smoke-exhausted space.<ref name="atriumsmokec_Milke-spill-verified">Milke (2002), pp. 4-301–4-302.</ref> | |||
A balcony is not represented solely by subtracting its height from the plume rise. Milke identifies horizontal travel, the opening from the adjoining room and the width of the spill as relevant characteristics. Vertical barriers beneath a balcony can restrict lateral spreading. Their effect belongs to the particular smoke route being assessed.<ref name="atriumsmokec_Milke-301" /> | A balcony is not represented solely by subtracting its height from the plume rise. Milke identifies horizontal travel, the opening from the adjoining room and the width of the spill as relevant characteristics. Vertical barriers beneath a balcony can restrict lateral spreading. Their effect belongs to the particular smoke route being assessed.<ref name="atriumsmokec_Milke-301" /> | ||
A fire curtain also raises a barrier-performance question within the overall strategy. Milke relates the effectiveness of separating barriers to leakage, pressure differences and resistance to the smoke's thermal exposure. A nominal boundary on a drawing does not determine those properties | A fire curtain also raises a barrier-performance question within the overall strategy. Milke relates the effectiveness of separating barriers to leakage, pressure differences and resistance to the smoke's thermal exposure. A nominal boundary on a drawing does not determine those properties; the barrier arrangement and its role in the smoke path remain explicit parts of the scenario.<ref name="atriumsmokec_Milke-294">Milke (2002), pp. 4-294–4-295.</ref> | ||
== Smoke filling before extraction operates == | == Smoke filling before extraction operates == | ||
| Line 85: | Line 87: | ||
Smoke does not necessarily form a complete upper layer immediately after ignition. It first travels upwards in the plume and then spreads horizontally beneath the ceiling. Milke calls these intervals the plume and ceiling-jet transport lags. In a large atrium, the time required to establish a layer can be appreciable.<ref name="atriumsmokec_Milke-295">Milke (2002), pp. 4-295–4-296.</ref> | Smoke does not necessarily form a complete upper layer immediately after ignition. It first travels upwards in the plume and then spreads horizontally beneath the ceiling. Milke calls these intervals the plume and ceiling-jet transport lags. In a large atrium, the time required to establish a layer can be appreciable.<ref name="atriumsmokec_Milke-295">Milke (2002), pp. 4-295–4-296.</ref> | ||
Once a layer develops, its interface can descend rapidly. A high interface permits a long plume rise, with substantial entrainment before the plume enters the layer. As the interface descends, the clear plume height decreases and the entrainment changes | Once a layer develops, its interface can descend rapidly. A high interface permits a long plume rise, with substantial entrainment before the plume enters the layer. As the interface descends, the clear plume height decreases and the entrainment changes; this makes the filling process time-dependent even when a simplified fire source is used.<ref name="atriumsmokec_Milke-296">Milke (2002), pp. 4-296–4-298.</ref> | ||
The period before system actuation therefore matters separately from the eventual exhaust capacity. A calculation of a steady layer after extraction begins does not establish the conditions during detection and start-up. Smoke can already have reached occupied levels during that earlier period. Milke evaluates the filling and vented periods as distinct stages of the same hazard analysis.<ref name="atriumsmokec_Milke-295" /><ref name="atriumsmokec_Milke-302">Milke (2002), pp. 4-302–4-303.</ref> | The period before system actuation therefore matters separately from the eventual exhaust capacity. A calculation of a steady layer after extraction begins does not establish the conditions during detection and start-up. Smoke can already have reached occupied levels during that earlier period. Milke evaluates the filling and vented periods as distinct stages of the same hazard analysis.<ref name="atriumsmokec_Milke-295" /><ref name="atriumsmokec_Milke-302">Milke (2002), pp. 4-302–4-303.</ref> | ||
| Line 96: | Line 98: | ||
A zone model represents an atrium using a small number of regions with uniform properties. This can describe layer development efficiently where its assumptions fit the geometry and smoke behaviour. Van Rossum identifies uniform layers, simple geometry and relatively undisturbed plume rise as central limitations. Complex local flow cannot be inferred merely from the model's average layer conditions.<ref name="atriumsmokec_VR-9.1">Van Rossum (2027), §§9.1–9.2.</ref> | A zone model represents an atrium using a small number of regions with uniform properties. This can describe layer development efficiently where its assumptions fit the geometry and smoke behaviour. Van Rossum identifies uniform layers, simple geometry and relatively undisturbed plume rise as central limitations. Complex local flow cannot be inferred merely from the model's average layer conditions.<ref name="atriumsmokec_VR-9.1">Van Rossum (2027), §§9.1–9.2.</ref> | ||
[[File:fse-nfpa-92-v3.svg|thumb|upright=1.5|alt=NFPA 92: choosing an analysis method, showing the relationships described in the text.|Choosing an analysis method in the assessment of NFPA 92.]] | |||
Milke identifies situations where that simplification becomes questionable. A narrow atrium can confine the widening plume before it reaches the ceiling. A broad atrium can have relevant horizontal differences within the smoke. Sprinkler cooling and spray-driven mixing can also alter the assumed separation between upper and lower regions.<ref name="atriumsmokec_Milke-294" /><ref name="atriumsmokec_Milke-304" /> | Milke identifies situations where that simplification becomes questionable. A narrow atrium can confine the widening plume before it reaches the ceiling. A broad atrium can have relevant horizontal differences within the smoke. Sprinkler cooling and spray-driven mixing can also alter the assumed separation between upper and lower regions.<ref name="atriumsmokec_Milke-294" /><ref name="atriumsmokec_Milke-304" /> | ||
| Line 101: | Line 104: | ||
Field models and physical scale models provide other ways to investigate selected problems. Milke discusses their use for irregular geometries and situations where local conditions matter. Their selection still depends on the phenomena and accuracy required. A more detailed representation does not remove the need to define the fire, openings, thermal boundaries and operating sequence.<ref name="atriumsmokec_Milke-294" /> | Field models and physical scale models provide other ways to investigate selected problems. Milke discusses their use for irregular geometries and situations where local conditions matter. Their selection still depends on the phenomena and accuracy required. A more detailed representation does not remove the need to define the fire, openings, thermal boundaries and operating sequence.<ref name="atriumsmokec_Milke-294" /> | ||
Comparing model results requires a consistent definition of the smoke interface. Milke distinguishes the first detectable smoke in experiments from the boundary between idealised zones | Comparing model results requires a consistent definition of the smoke interface. Milke distinguishes the first detectable smoke in experiments from the boundary between idealised zones; their numerical elevations can differ without either calculation describing exactly the same quantity. The assessment therefore identifies which interface definition is being compared with an occupied level or another design criterion.<ref name="atriumsmokec_Milke-296" /> | ||
Environmental and system assumptions also influence the appropriate method. Milke includes wind, stack effects, interacting ventilation systems and the period of interest among the selection considerations. A calculation that excludes an influence cannot demonstrate its insignificance merely through a precise numerical result. Its applicability instead rests on the stated relationship between the chosen model and the actual scenario.<ref name="atriumsmokec_Milke-294" /> | Environmental and system assumptions also influence the appropriate method. Milke includes wind, stack effects, interacting ventilation systems and the period of interest among the selection considerations. A calculation that excludes an influence cannot demonstrate its insignificance merely through a precise numerical result. Its applicability instead rests on the stated relationship between the chosen model and the actual scenario.<ref name="atriumsmokec_Milke-294" /> | ||
| Line 115: | Line 118: | ||
== References == | == References == | ||
* Australian Building Codes Board | * Australian Building Codes Board. (2020). ''Fire safety verification method: Data sheets'' (Handbook annex, Print version 1.1). | ||
* Cote, A. E., Grant, C. C., Hall, J. R., Jr., & Solomon, R. E. (Eds.). (2008). ''Fire protection handbook'' (20th ed.). National Fire Protection Association. | * Cote, A. E., Grant, C. C., Hall, J. R., Jr., & Solomon, R. E. (Eds.). (2008). ''Fire protection handbook'' (20th ed.). National Fire Protection Association. | ||
* Klote, J. H. (2002). Smoke control. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed., pp. 4-274–4-291). National Fire Protection Association. | * Klote, J. H. (2002). Smoke control. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed., pp. 4-274–4-291). National Fire Protection Association. | ||
Latest revision as of 09:21, 13 November 2026
NFPA 92 is the National Fire Protection Association (NFPA) standard identified as Standard for Smoke Control Systems in the Australian Building Codes Board's 2020 fire-engineering data sheets. Those sheets cite its 2018 edition as a source of design-fire information. The engineering subject is the control of smoke movement, described in the Society of Fire Protection Engineers (SFPE) Handbook through airflow, pressure differences and smoke-management methods.[1][2]
The 2008 NFPA Fire Protection Handbook discusses two earlier documents: NFPA 92A for systems using barriers and pressure differences, and NFPA 92B for malls, atria and large spaces. That account provides the historical framework used here. Edition-specific requirements remain separate from the physical principles and design examples explained in the handbooks.[3]
The common engineering task is to define the protected spaces, the expected fire and the performance of the complete system. Atrium smoke control, stair pressurisation and zoned smoke control apply different mechanisms. Their calculations, operating sequences and acceptance evidence therefore address different building conditions.[4]
Document context and the scope of an assessment
NFPA guidance is cited by both the NFPA Fire Protection Handbook and the SFPE Handbook. The 2008 NFPA account associates NFPA 92A with pressurised stairs and zones separated by barriers. It associates NFPA 92B with large-volume spaces where a smoke layer develops above occupied levels; these are related objectives, but their geometries and governing flows differ.[5][6]
The later Australian data sheets cite the 2018 NFPA 92 title when discussing fire-growth information. A citation to that edition establishes the source being referenced; it does not make every older handbook example a clause of the later standard. A design assessment consequently identifies the governing edition and retains the separate origins of its input data and calculation methods.[1][5]
Smoke control starts with an objective. Protecting a stair against smoke infiltration differs from maintaining an upper smoke layer in a large hall. Removing residual smoke after a fire is another operation. Klote explains that dilution in the fire space cannot substitute for the pressure and airflow conditions needed to control smoke movement.[7]
The expected fire determines heat and smoke production, while the geometry determines entrainment and movement; the Australian data sheets describe characteristic growth rates and sensitivity to their selection. Those rates are inputs to an assessment rather than predictions that every fire follows an identical curve. The chosen scenario and period of interest remain attached to the result.[1]
The evidence also distinguishes equipment availability from adequacy for the selected fire; a fan can run as intended while its capacity is insufficient for the assumed smoke production. Conversely, a suitable design can fail to operate because a control or power dependency is unavailable. The Australian data sheets separate these performance questions when discussing smoke-control effectiveness.[8]
Pressure systems and their physical basis
Pressure drives airflow through gaps in a boundary. Klote describes the flow using an effective leakage area and a coefficient representing the opening geometry. For most paths other than extremely narrow cracks, a square-root pressure relationship is a useful approximation. The required fan flow consequently depends on the openings as well as the selected pressure difference.[9]
| Symbol | Description | Unit |
|---|---|---|
| Volume flow through the opening | m³/s | |
| Flow coefficient | Dimensionless | |
| Effective leakage area | m² | |
| Pressure difference across the opening | Pa | |
| Density of the entering air | kg/m³ |
Klote's example uses a leakage area of 0.01 m². With a flow coefficient of 0.65 and air density of 1.2 kg/m³, a pressure difference of 2.5 Pa gives approximately 0.013 m³/s. Increasing the pressure difference to 75 Pa gives approximately 0.073 m³/s; these are calculations for the stated closed-door leakage, not for an open doorway.[10]
An opened door changes the flow area substantially. Pressure differences elsewhere can then fall, even while the fan continues to run. Open-door control is consequently assessed in terms of the appropriate airflow, whereas closed-door performance is commonly assessed through pressure differences. The operating state belongs with every calculation and measurement.[11]
Increasing pressure has a competing effect on door operation. The pressure difference adds force at the door leaf, and the closer contributes another force. A system that restricts smoke but makes an escape door difficult to operate has not resolved the combined problem. Leakage, airflow and door forces therefore remain linked design conditions.[12]
Equipment states and demonstrated performance
A smoke damper, fan and initiating detector contribute to a sequence that changes the building's airflows. The NFPA handbook describes the practical difficulty of integrating fire alarm controls with ventilation equipment; the intended state of every controlled path must follow the identified fire condition. Testing one device alone cannot demonstrate that the whole sequence is correct.[13]
The complete control sequence requires an operational check as well as a component inspection. The NFPA handbook describes interfaces between fire alarms and building ventilation systems, often installed by different trades. Correctly operating individual components does not establish that their combined sequence is correct; the initiating signal, damper positions and fan operation must describe the same intended fire condition.[13]
The Australian Building Codes Board's 2020 data sheets distinguish installation checks from tests of system performance in its required operating modes. They describe defect correction followed by retesting. These activities connect the design assumptions to the installed arrangement. A completed drawing or equipment label cannot supply the results of those operational tests.[14]
Changes to a building can alter both its leakage and its controls. New partitions change flow paths, while altered ventilation zones can change which spaces receive or lose air. Continued inspection and maintenance therefore concern the system configuration as well as the condition of each device. Access for checking dampers and other equipment supports that continuing assessment.[14]
Dependence on another protection system also belongs in the assessment. Where the smoke design assumes that sprinklers limit the fire, failure of suppression can increase smoke production and thermal exposure. The data sheets identify this as a linked failure condition. The two systems cannot be assigned independent successful outcomes when one depends on the other's performance.[15]
What the system is intended to protect
Atria connect spaces that might otherwise be separated into smaller compartments. Without suitable barriers, smoke can spread through the shared volume and reach communicating areas. Milke identifies this as a different problem from smoke control in a well-compartmented building. Pressure differences across barriers cannot perform the same function where the required physical separation is absent.[16]
The large volume can initially moderate the hazard. Air mixed into the plume reduces the concentration of combustion products and lowers the smoke temperature. However, dilution also increases the quantity of gas delivered to the layer. A benefit in concentration therefore accompanies an increased smoke-handling demand.[17]
Life-safety assessment considers several properties of the smoke environment. These include layer-interface height, visibility, temperature and the concentrations of harmful gases. The layer height describes whether an occupied level becomes immersed in smoke; it does not, by itself, describe the severity of every possible exposure within that layer.[17]
Reduced visibility can slow movement and increase disorientation. Milke also describes the potential for trips and falls where occupants cannot see obstructions or balcony edges. Longer evacuation then extends the period of exposure to smoke. A low predicted temperature does not remove these visibility-related effects.[17]
Property objectives can differ from life-safety objectives. Smoke can stain contents, expose equipment to corrosive products and interrupt the use of a building. A smoke concentration that permits short-term movement can still be unacceptable for sensitive contents. The chosen performance objective therefore influences the conditions that the system is intended to maintain.[17]
Fire locations and communicating spaces
The design distinguishes a fire on the atrium floor from a fire in an adjoining room. A fire remote from walls can produce an approximately axisymmetric plume, with air entering around its perimeter. Wall and corner locations restrict some of that air access. Their entrainment behaviour therefore differs from the free-plume case.[18]
A fire in a shop or another communicating space can produce a balcony spill plume. Smoke first rises to an intermediate ceiling, travels beneath it and then spills around an edge. Its subsequent rise into the atrium has a different geometry from a plume rising directly above a floor-level fire. The width and route of the spill become relevant inputs.[19]
An adjoining-room scenario can involve several stages of mixing before smoke reaches the upper layer; modelling only a fire in the open atrium can omit those stages. Milke therefore distinguishes a balcony spill plume from a plume rising directly above a fire in the open volume. The assessment includes the actual connections between the room of origin and the smoke-exhausted space.[20]
A balcony is not represented solely by subtracting its height from the plume rise. Milke identifies horizontal travel, the opening from the adjoining room and the width of the spill as relevant characteristics. Vertical barriers beneath a balcony can restrict lateral spreading. Their effect belongs to the particular smoke route being assessed.[19]
A fire curtain also raises a barrier-performance question within the overall strategy. Milke relates the effectiveness of separating barriers to leakage, pressure differences and resistance to the smoke's thermal exposure. A nominal boundary on a drawing does not determine those properties; the barrier arrangement and its role in the smoke path remain explicit parts of the scenario.[21]
Smoke filling before extraction operates
Smoke does not necessarily form a complete upper layer immediately after ignition. It first travels upwards in the plume and then spreads horizontally beneath the ceiling. Milke calls these intervals the plume and ceiling-jet transport lags. In a large atrium, the time required to establish a layer can be appreciable.[22]
Once a layer develops, its interface can descend rapidly. A high interface permits a long plume rise, with substantial entrainment before the plume enters the layer. As the interface descends, the clear plume height decreases and the entrainment changes; this makes the filling process time-dependent even when a simplified fire source is used.[23]
The period before system actuation therefore matters separately from the eventual exhaust capacity. A calculation of a steady layer after extraction begins does not establish the conditions during detection and start-up. Smoke can already have reached occupied levels during that earlier period. Milke evaluates the filling and vented periods as distinct stages of the same hazard analysis.[22][24]
Smoke stratification can also occur at an intermediate elevation below the roof. Warm air accumulated near the top of an atrium can reduce the relative buoyancy of an arriving plume. The plume may then stop rising before reaching ceiling-mounted detectors. This condition differs from a smoke layer that has formed at the ceiling and subsequently descended.[25]
Milke discusses beam detection below the expected stratification elevation as one response to this scenario. The objective is to intercept smoke where it actually travels. The source also describes how operating exhaust can remove the warm upper air and change the subsequent smoke movement. Detection and ventilation assumptions therefore need a consistent account of the initial temperature profile.[25]
Choosing an analysis method
A zone model represents an atrium using a small number of regions with uniform properties. This can describe layer development efficiently where its assumptions fit the geometry and smoke behaviour. Van Rossum identifies uniform layers, simple geometry and relatively undisturbed plume rise as central limitations. Complex local flow cannot be inferred merely from the model's average layer conditions.[26]
Milke identifies situations where that simplification becomes questionable. A narrow atrium can confine the widening plume before it reaches the ceiling. A broad atrium can have relevant horizontal differences within the smoke. Sprinkler cooling and spray-driven mixing can also alter the assumed separation between upper and lower regions.[21][25]
Field models and physical scale models provide other ways to investigate selected problems. Milke discusses their use for irregular geometries and situations where local conditions matter. Their selection still depends on the phenomena and accuracy required. A more detailed representation does not remove the need to define the fire, openings, thermal boundaries and operating sequence.[21]
Comparing model results requires a consistent definition of the smoke interface. Milke distinguishes the first detectable smoke in experiments from the boundary between idealised zones; their numerical elevations can differ without either calculation describing exactly the same quantity. The assessment therefore identifies which interface definition is being compared with an occupied level or another design criterion.[23]
Environmental and system assumptions also influence the appropriate method. Milke includes wind, stack effects, interacting ventilation systems and the period of interest among the selection considerations. A calculation that excludes an influence cannot demonstrate its insignificance merely through a precise numerical result. Its applicability instead rests on the stated relationship between the chosen model and the actual scenario.[21]
See also
Notes
- ↑ 1.0 1.1 1.2 Australian Building Codes Board (2020), Data Sheet B1, pp. 11, 23.
- ↑ Klote (2002), pp. 4-274–4-279.
- ↑ Cote et al. (2008), §18.3, pp. 18-43, 18-55.
- ↑ Cote et al. (2008), §18.3, pp. 18-51–18-53.
- ↑ 5.0 5.1 Cote et al. (2008), §18.3, p. 18-43.
- ↑ Klote (2002), pp. 4-278–4-279.
- ↑ Klote (2002), pp. 4-278–4-281.
- ↑ Australian Building Codes Board (2020), Data Sheet C4, pp. 129–132.
- ↑ Klote (2002), pp. 4-280–4-282.
- ↑ Klote (2002), pp. 4-280–4-281.
- ↑ Klote (2002), pp. 4-278–4-282.
- ↑ Klote (2002), pp. 4-281–4-282.
- ↑ 13.0 13.1 Cote et al. (2008), §14.4, p. 14-47.
- ↑ 14.0 14.1 Australian Building Codes Board (2020), Data Sheet C4, pp. 130–131.
- ↑ Australian Building Codes Board (2020), Data Sheet C4, pp. 131–132.
- ↑ Milke (2002), pp. 4-292–4-294.
- ↑ 17.0 17.1 17.2 17.3 Milke (2002), pp. 4-292–4-293.
- ↑ Milke (2002), pp. 4-299–4-300.
- ↑ 19.0 19.1 Milke (2002), pp. 4-301–4-302.
- ↑ Milke (2002), pp. 4-301–4-302.
- ↑ 21.0 21.1 21.2 21.3 Milke (2002), pp. 4-294–4-295.
- ↑ 22.0 22.1 Milke (2002), pp. 4-295–4-296.
- ↑ 23.0 23.1 Milke (2002), pp. 4-296–4-298.
- ↑ Milke (2002), pp. 4-302–4-303.
- ↑ 25.0 25.1 25.2 Milke (2002), pp. 4-304–4-305.
- ↑ Van Rossum (2027), §§9.1–9.2.
References
- Australian Building Codes Board. (2020). Fire safety verification method: Data sheets (Handbook annex, Print version 1.1).
- Cote, A. E., Grant, C. C., Hall, J. R., Jr., & Solomon, R. E. (Eds.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
- Klote, J. H. (2002). Smoke control. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-274–4-291). National Fire Protection Association.
- Milke, J. A. (2002). Smoke management in covered malls and atria. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-292–4-310). National Fire Protection Association.
- Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.