Skip to content

Control mode specific application sprinkler: Difference between revisions

From Fire Safety Academy Wiki
Daan (talk | contribs)
New FSE wiki article: Control mode specific application sprinkler (written by GPT-6)
 
Peter (talk | contribs)
Wiki review: corrected 11 errors: citation (11) (Claude Opus 5.5)
 
(2 intermediate revisions by 2 users not shown)
Line 4: Line 4:


== Specific-application control criteria ==
== Specific-application control criteria ==
The [[Sprinkler head|sprinkler head]] is selected as part of a tested protection method for a [[Warehouse fire|warehouse fire]] scenario. The [[Large-drop sprinkler|large-drop sprinkler]] was an early example described by the handbook. Later devices can have different orifices and application limits. The common CMSA label does not make those devices interchangeable across every permitted storage arrangement. <ref name="H_16_5_16-80">Cote (2008), ch. 16.5, pp. 16-80.</ref>
The [[Sprinkler head|sprinkler head]] is selected as part of a tested protection method for a [[Warehouse fire|warehouse fire]] scenario; the [[Large-drop sprinkler|large-drop sprinkler]] was an early example described by the handbook. Later devices can have different orifices and application limits. The common CMSA label does not make those devices interchangeable across every permitted storage arrangement. <ref name="H_16_5_16-80">Cote (2008), ch. 16.5, p. 16-80.</ref>
[[File:fse-control-mode-specific-application-sprinkler-v1.svg|thumb|upright=1.5|alt=Control mode specific application sprinkler: functional relationships. Mechanism and application limits are distinguished.|Control mode specific application sprinkler: functional relationships. Schematic explanation; dimensions are not installation instructions.]]


[[Fire control and fire suppression]] describe different intended outcomes. An [[ESFR sprinkler]] uses another protection approach intended for early suppression, while CMSA remains a control-mode designation. [[Rack storage]] can be protected through different established combinations of ceiling and in-rack equipment. Selection depends on the complete arrangement rather than the perceived superiority of one broad label. <ref name="H_16_5_16-79_16-84">Cote (2008), ch. 16.5, pp. 16-79–16-84.</ref>
[[Fire control and fire suppression]] describe different intended outcomes; an [[ESFR sprinkler]] uses another protection approach intended for early suppression, while CMSA remains a control-mode designation. [[Rack storage]] can be protected through different established combinations of ceiling and in-rack equipment. Selection depends on the complete arrangement rather than the perceived superiority of one broad label. <ref name="H_16_5_16-79_16-84">Cote (2008), ch. 16.5, pp. 16-79–16-84.</ref>


The minimum pressure in a specific-application table is not reduced simply by reducing the assigned area per sprinkler. That differs from the arithmetic of a conventional density-area design. A sprinkler-count criterion also defines the operating demand differently from a nominal floor area. Preserving this distinction prevents a hydraulic redesign from inadvertently changing the underlying fire-performance basis. <ref name="H_16_5_16-80_16-83" />
The minimum pressure in a specific-application table is not reduced simply by reducing the assigned area per sprinkler; that differs from the arithmetic of a conventional density-area design. A sprinkler-count criterion also defines the operating demand differently from a nominal floor area. Preserving this distinction prevents a hydraulic redesign from inadvertently changing the underlying fire-performance basis. <ref name="H_16_5_16-80_16-83" />


== Selecting a storage protection method ==
== Selecting a storage protection method ==
The handbook distinguishes control-mode density-area, control-mode specific-application and suppression-mode sprinkler protection. These are different design approaches with different equipment and criteria. A similar nominal flow does not make their fire performance interchangeable. The selected method must match the commodity, storage arrangement and building conditions. <ref name="H_16_5_16-79_16-83">Cote (2008), ch. 16.5, pp. 16-79–16-83.</ref>
The handbook distinguishes control-mode density-area, control-mode specific-application and suppression-mode sprinkler protection; these are different design approaches with different equipment and criteria. A similar nominal flow does not make their fire performance interchangeable. The selected method must match the commodity, storage arrangement and building conditions. <ref name="H_16_5_16-79_16-83">Cote (2008), ch. 16.5, pp. 16-79–16-83.</ref>
[[File:fse-control-mode-specific-application-sprinkler-v2.svg|thumb|upright=1.5|alt=Three protection methods. Mechanism and application limits are distinguished.|Three protection methods. Schematic explanation; dimensions are not installation instructions.]]


Density-area protection specifies an application density over an operating area. The assigned coverage of each sprinkler then determines its minimum flow and associated pressure. Actual network calculation accounts for pressure differences among the operating sprinklers. Ceiling-only arrangements and arrangements with in-rack sprinklers have different demands and protection assumptions. <ref name="H_16_5_16-80_16-81">Cote (2008), ch. 16.5, pp. 16-80–16-81.</ref><ref name="F_4-74_4-80">Fleming (2002), ch. 4-3, pp. 4-74–4-80.</ref>
Density-area protection specifies an application density over an operating area; the assigned coverage of each sprinkler then determines its minimum flow and associated pressure. Actual network calculation accounts for pressure differences among the operating sprinklers. Ceiling-only arrangements and arrangements with in-rack sprinklers have different demands and protection assumptions. <ref name="H_16_5_16-80_16-81">Cote (2008), ch. 16.5, pp. 16-80–16-81.</ref><ref name="F_4-74_4-80">Fleming (2002), ch. 4-3, pp. 4-74–4-80.</ref>


Specific-application protection instead uses a specified number of sprinklers at a minimum pressure for a tested arrangement. The handbook identifies the large-drop sprinkler as an early example of this approach. Later designs use other orifice and deflector combinations. Permission for one type in a particular storage arrangement does not establish suitability of another type. <ref name="H_16_5_16-80_16-83" />
Specific-application protection instead uses a specified number of sprinklers at a minimum pressure for a tested arrangement; the handbook identifies the large-drop sprinkler as an early example of this approach. Later designs use other orifice and deflector combinations. Permission for one type in a particular storage arrangement does not establish suitability of another type. <ref name="H_16_5_16-80_16-83" />


Early-suppression fast-response sprinklers combine rapid thermal response with a high-volume discharge intended to suppress the developing storage fire. Their benefit does not arise from sensitivity alone. Water momentum, distribution, ceiling geometry and installation conditions form part of the method. An ordinary quick-response sprinkler therefore cannot be assumed to provide the same protection. <ref name="H_16_5_16-80_16-83" /><ref name="H_16_2_16-27">Cote (2008), ch. 16.2, pp. 16-27.</ref>
Early-suppression fast-response sprinklers combine rapid thermal response with a high-volume discharge intended to suppress the developing storage fire; their benefit does not arise from sensitivity alone. Water momentum, distribution, ceiling geometry and installation conditions form part of the method. An ordinary quick-response sprinkler therefore cannot be assumed to provide the same protection. <ref name="H_16_5_16-80_16-83" /><ref name="H_16_2_16-27">Cote (2008), ch. 16.2, p. 16-27.</ref>


In-rack protection offers another means of placing water near shielded fuel. It can reduce the challenge that reaches the ceiling by controlling local spread. However, rack piping and sprinklers can be exposed to mechanical damage during materials handling. Their arrangement and continued condition are part of the protection strategy, rather than an optional addition to an unchanged ceiling calculation. <ref name="H_16_5_16-77_16-80_16-84">Cote (2008), ch. 16.5, pp. 16-77,16-80,16-84.</ref>
In-rack protection offers another means of placing water near shielded fuel; it can reduce the challenge that reaches the ceiling by controlling local spread. However, rack piping and sprinklers can be exposed to mechanical damage during materials handling. Their arrangement and continued condition are part of the protection strategy, rather than an optional addition to an unchanged ceiling calculation. <ref name="H_16_5_16-77_16-80_16-84">Cote (2008), ch. 16.5, pp. 16-77,16-80,16-84.</ref>


The water supply must support the selected combination of ceiling sprinklers, in-rack sprinklers and applicable hose demand for the specified duration. Hydraulic adequacy does not establish that a different storage configuration will be controlled. Fleming separates delivery calculations from fire-performance evidence for this reason. The complete design preserves both the hydraulic requirements and the tested application boundaries. <ref name="H_16_5_16-85_16-86">Cote (2008), ch. 16.5, pp. 16-85–16-86.</ref><ref name="F_4-72_4-75" />
The water supply must support the selected combination of ceiling sprinklers, in-rack sprinklers and applicable hose demand for the specified duration. Hydraulic adequacy does not establish that a different storage configuration will be controlled. Fleming separates delivery calculations from fire-performance evidence for this reason. The complete design preserves both the hydraulic requirements and the tested application boundaries. <ref name="H_16_5_16-85_16-86">Cote (2008), ch. 16.5, pp. 16-85–16-86.</ref><ref name="F_4-72_4-75" />


== Water distribution and fire performance ==
== Water distribution and fire performance ==
Water can influence a fire by cooling burning material, wetting nearby fuel and absorbing heat from hot gases. The relative importance of these mechanisms depends on the sprinkler and the fire arrangement. Water discharged at the ceiling is not necessarily water delivered to the burning surface. Upward gas movement and intervening objects can redirect or prevent delivery. <ref name="H_16_1_16-6_16-8">Cote (2008), ch. 16.1, pp. 16-6–16-8.</ref><ref name="F_4-85_4-87">Fleming (2002), ch. 4-3, pp. 4-85–4-87.</ref>
Water can influence a fire by cooling burning material, wetting nearby fuel and absorbing heat from hot gases; the relative importance of these mechanisms depends on the sprinkler and the fire arrangement. Water discharged at the ceiling is not necessarily water delivered to the burning surface. Upward gas movement and intervening objects can redirect or prevent delivery. <ref name="H_16_1_16-6_16-8">Cote (2008), ch. 16.1, pp. 16-6–16-8.</ref><ref name="F_4-85_4-87">Fleming (2002), ch. 4-3, pp. 4-85–4-87.</ref>
[[File:fse-control-mode-specific-application-sprinkler-v3.svg|thumb|upright=1.5|alt=Water reaching the fire. Mechanism and application limits are distinguished.|Water reaching the fire. Schematic explanation; dimensions are not installation instructions.]]


Droplet size creates a physical trade-off. Smaller droplets expose more surface area for a given volume of water and can exchange heat rapidly. Larger droplets can have greater ability to penetrate an upward-moving plume. Effective sprinkler design considers momentum, distribution and the intended fire challenge together, rather than maximising one characteristic in isolation. <ref name="H_16_1_16-6_16-9">Cote (2008), ch. 16.1, pp. 16-6–16-9.</ref><ref name="H_16_2_16-23_16-27">Cote (2008), ch. 16.2, pp. 16-23,16-27.</ref>
Droplet size creates a physical trade-off; smaller droplets expose more surface area for a given volume of water and can exchange heat rapidly. Larger droplets can have greater ability to penetrate an upward-moving plume. Effective sprinkler design considers momentum, distribution and the intended fire challenge together, rather than maximising one characteristic in isolation. <ref name="H_16_1_16-6_16-9">Cote (2008), ch. 16.1, pp. 16-6–16-9.</ref><ref name="H_16_2_16-23_16-27">Cote (2008), ch. 16.2, pp. 16-23,16-27.</ref>


Pressure and orifice geometry influence spray formation. A higher discharge pressure does not simply spread a fixed amount of water more effectively over every protected surface. The handbook describes changes in droplet behaviour and warns against assuming that increased pressure always improves coverage. The resulting pattern belongs to a specified sprinkler operating within its intended conditions. <ref name="H_16_1_16-6">Cote (2008), ch. 16.1, pp. 16-6.</ref><ref name="H_16_5_16-85">Cote (2008), ch. 16.5, pp. 16-85.</ref>
Pressure and orifice geometry influence spray formation; a higher discharge pressure does not simply spread a fixed amount of water more effectively over every protected surface. The handbook describes changes in droplet behaviour and warns against assuming that increased pressure always improves coverage. The resulting pattern belongs to a specified sprinkler operating within its intended conditions. <ref name="H_16_1_16-6">Cote (2008), ch. 16.1, p. 16-6.</ref><ref name="H_16_5_16-85">Cote (2008), ch. 16.5, p. 16-85.</ref>


The distinction between floor-area density and water reaching fuel is particularly important in storage. A nominal density describes a design quantity over an assigned area. Actual delivered water can be obstructed by shelves, packaging or the geometry of the goods. The critical application rate at a burning surface is therefore not automatically the same number as the nominal sprinkler design density. <ref name="H_16_1_16-7_16-8">Cote (2008), ch. 16.1, pp. 16-7–16-8.</ref><ref name="H_16_5_16-74_16-84">Cote (2008), ch. 16.5, pp. 16-74–16-84.</ref>
The distinction between floor-area density and water reaching fuel is particularly important in storage; a nominal density describes a design quantity over an assigned area. Actual delivered water can be obstructed by shelves, packaging or the geometry of the goods. The critical application rate at a burning surface is therefore not automatically the same number as the nominal sprinkler design density. <ref name="H_16_1_16-7_16-8">Cote (2008), ch. 16.1, pp. 16-7–16-8.</ref><ref name="H_16_5_16-74_16-84">Cote (2008), ch. 16.5, pp. 16-74–16-84.</ref>


Control limits the growth or spread of a fire sufficiently for the intended protection objective. Suppression involves a stronger reduction in burning, while complete extinguishment means that combustion has ceased. The handbook describes different sprinkler technologies developed around these objectives. A successfully operating sprinkler does not establish which outcome has occurred without considering the fire and water interaction. <ref name="H_16_3_16-38">Cote (2008), ch. 16.3, pp. 16-38.</ref><ref name="H_16_5_16-79_16-80">Cote (2008), ch. 16.5, pp. 16-79–16-80.</ref>
Control limits the growth or spread of a fire sufficiently for the intended protection objective; suppression involves a stronger reduction in burning, while complete extinguishment means that combustion has ceased. The handbook describes different sprinkler technologies developed around these objectives. A successfully operating sprinkler does not establish which outcome has occurred without considering the fire and water interaction. <ref name="H_16_3_16-38">Cote (2008), ch. 16.3, p. 16-38.</ref><ref name="H_16_5_16-79_16-80">Cote (2008), ch. 16.5, pp. 16-79–16-80.</ref>


The International Fire Engineering Guidelines (IFEG) illustrates possible design-fire outcomes as continued growth, control or extinguishment. A steady heat-release rate after activation is a modelling representation of control, not a universal measured sprinkler response. A decay curve likewise requires an appropriate basis. Fleming's discussion of furnishing-fire suppression models identifies fuel and test limitations that prevent unrestricted transfer to shielded warehouse fires. <ref name="I_1_7-7">National Research Council of Canada et al. (2005), pp. 1.7-7.</ref><ref name="F_4-86_4-87">Fleming (2002), ch. 4-3, pp. 4-86–4-87.</ref>
The International Fire Engineering Guidelines (IFEG) illustrates possible design-fire outcomes as continued growth, control or extinguishment; a steady heat-release rate after activation is a modelling representation of control, not a universal measured sprinkler response. A decay curve likewise requires an appropriate basis. Fleming's discussion of furnishing-fire suppression models identifies fuel and test limitations that prevent unrestricted transfer to shielded warehouse fires. <ref name="I_1_7-7">National Research Council of Canada et al. (2005), p. 1.7-7.</ref><ref name="F_4-86_4-87">Fleming (2002), ch. 4-3, pp. 4-86–4-87.</ref>


== Discharge, pressure and assigned area ==
== Discharge, pressure and assigned area ==
Hydraulic calculation starts with the water discharge required at an individual operating sprinkler. In a density-area design, the assigned area and selected application density determine that minimum discharge. The assigned area comes from the spacing method used for the design. It is not an assertion that every point beneath the sprinkler receives an identical local quantity. <ref name="F_4-74_4-75">Fleming (2002), ch. 4-3, pp. 4-74–4-75.</ref><ref name="H_16_1_16-6_16-8" />
Hydraulic calculation starts with the water discharge required at an individual operating sprinkler; in a density-area design, the assigned area and selected application density determine that minimum discharge. The assigned area comes from the spacing method used for the design. It is not an assertion that every point beneath the sprinkler receives an identical local quantity. <ref name="F_4-74_4-75">Fleming (2002), ch. 4-3, pp. 4-74–4-75.</ref><ref name="H_16_1_16-6_16-8" />


The discharge coefficient, or K-factor, relates flow to the square root of pressure at the sprinkler. Its numerical value depends on the units used for both quantities. A value stated for pressure in bar cannot be inserted unchanged when pressure is in kilopascals. The unit convention is part of the coefficient's definition. <ref name="H_16_2_16-25_16-26">Cote (2008), ch. 16.2, pp. 16-25–16-26.</ref><ref name="F_4-75">Fleming (2002), ch. 4-3, pp. 4-75.</ref>
The discharge coefficient, or K-factor, relates flow to the square root of pressure at the sprinkler; its numerical value depends on the units used for both quantities. A value stated for pressure in bar cannot be inserted unchanged when pressure is in kilopascals. The unit convention is part of the coefficient's definition. <ref name="H_16_2_16-25_16-26">Cote (2008), ch. 16.2, pp. 16-25–16-26.</ref><ref name="F_4-75">Fleming (2002), ch. 4-3, p. 4-75.</ref>


<math display="block">q=dA_s=K\sqrt{p},\qquad p=\left(\frac{q}{K}\right)^2</math>
<math display="block">q=dA_s=K\sqrt{p},\qquad p=\left(\frac{q}{K}\right)^2</math>
Line 57: Line 60:
Using the rounded metric inputs in Fleming's example, 6.1 L/(min·m²) over 15.6 m² requires 95.2 L/min. With a nominal K-factor of 8.0 L/(min·√kPa), the calculated pressure is approximately 142 kPa. The corresponding bar-based K-factor is 80 L/(min·√bar). The example illustrates the calculation method, rather than selecting a density for a new hazard. <ref name="F_4-75" /><ref name="H_16_2_16-25_16-26" />
Using the rounded metric inputs in Fleming's example, 6.1 L/(min·m²) over 15.6 m² requires 95.2 L/min. With a nominal K-factor of 8.0 L/(min·√kPa), the calculated pressure is approximately 142 kPa. The corresponding bar-based K-factor is 80 L/(min·√bar). The example illustrates the calculation method, rather than selecting a density for a new hazard. <ref name="F_4-75" /><ref name="H_16_2_16-25_16-26" />


Other sprinklers in the operating area may have greater pressure than the limiting sprinkler. Their individual discharges then exceed the minimum flow calculated from density and coverage alone. Total demand is the sum of those actual calculated flows, with applicable additional demands considered separately. Simply multiplying nominal density by nominal design area can therefore understate the hydraulic result. <ref name="H_16_3_16-48_16-49">Cote (2008), ch. 16.3, pp. 16-48–16-49.</ref><ref name="F_4-75_4-80">Fleming (2002), ch. 4-3, pp. 4-75–4-80.</ref>
Other sprinklers in the operating area may have greater pressure than the limiting sprinkler; their individual discharges then exceed the minimum flow calculated from density and coverage alone. Total demand is the sum of those actual calculated flows, with applicable additional demands considered separately. Simply multiplying nominal density by nominal design area can therefore understate the hydraulic result. <ref name="H_16_3_16-48_16-49">Cote (2008), ch. 16.3, pp. 16-48–16-49.</ref><ref name="F_4-75_4-80">Fleming (2002), ch. 4-3, pp. 4-75–4-80.</ref>


A higher K-factor reduces the pressure required for a specified flow. It does not establish a particular spray pattern, response sensitivity or suitability for storage. Those characteristics depend on the complete sprinkler design and its tested application. Hydraulic equivalence is therefore narrower than equivalent fire protection performance. <ref name="H_16_2_16-23_16-27" /><ref name="H_16_5_16-80" />
A higher K-factor reduces the pressure required for a specified flow; it does not establish a particular spray pattern, response sensitivity or suitability for storage. Those characteristics depend on the complete sprinkler design and its tested application. Hydraulic equivalence is therefore narrower than equivalent fire protection performance. <ref name="H_16_2_16-23_16-27_29cadfc7">Cote (2008), ch. 16.2, pp. 16-23–16-27.</ref><ref name="H_16_5_16-80" />


== Thermal operation and water delivery ==
== Thermal operation and water delivery ==
An automatic sprinkler combines a heat-responsive element with a water-distribution device. The element responds to its own temperature, which follows the surrounding gas conditions with a delay. Water then needs an open discharge path and an adequate supply. These are successive physical processes, so activation time and effective water delivery are not interchangeable quantities. <ref name="F_4-72_4-73_4-85">Fleming (2002), ch. 4-3, pp. 4-72–4-73,4-85.</ref><ref name="H_16_1_16-4_16-6">Cote (2008), ch. 16.1, pp. 16-4–16-6.</ref>
An automatic sprinkler combines a heat-responsive element with a water-distribution device; the element responds to its own temperature, which follows the surrounding gas conditions with a delay. Water then needs an open discharge path and an adequate supply. These are successive physical processes, so activation time and effective water delivery are not interchangeable quantities. <ref name="F_4-72_4-73_4-85">Fleming (2002), ch. 4-3, pp. 4-72–4-73,4-85.</ref><ref name="H_16_1_16-4_16-6">Cote (2008), ch. 16.1, pp. 16-4–16-6.</ref>


Temperature rating describes the nominal operating temperature established under specified test conditions. Thermal sensitivity describes how quickly the element heats in a moving hot gas stream. A sprinkler can therefore have the same temperature rating as another device while responding differently to a growing fire. Gas velocity, heat conduction and the element's position beneath the ceiling influence that response. <ref name="H_16_2_16-17_16-18">Cote (2008), ch. 16.2, pp. 16-17–16-18.</ref><ref name="F_4-85">Fleming (2002), ch. 4-3, pp. 4-85.</ref>
Temperature rating describes the nominal operating temperature established under specified test conditions; thermal sensitivity describes how quickly the element heats in a moving hot gas stream. A sprinkler can therefore have the same temperature rating as another device while responding differently to a growing fire. Gas velocity, heat conduction and the element's position beneath the ceiling influence that response. <ref name="H_16_2_16-17_16-18">Cote (2008), ch. 16.2, pp. 16-17–16-18.</ref><ref name="F_4-85">Fleming (2002), ch. 4-3, p. 4-85.</ref>


The response time index provides a measure of thermal sensitivity. Lower values represent faster response under comparable convective heating conditions. The handbook relates this index to a thermal time constant and the square root of gas velocity. Conduction into the sprinkler frame introduces another influence, especially where convection is weak. <ref name="H_16_1_16-4_16-5">Cote (2008), ch. 16.1, pp. 16-4–16-5.</ref><ref name="H_16_6_16-95_16-96">Cote (2008), ch. 16.6, pp. 16-95–16-96.</ref>
The response time index provides a measure of thermal sensitivity; lower values represent faster response under comparable convective heating conditions. The handbook relates this index to a thermal time constant and the square root of gas velocity. Conduction into the sprinkler frame introduces another influence, especially where convection is weak. <ref name="H_16_1_16-4_16-5">Cote (2008), ch. 16.1, pp. 16-4–16-5.</ref><ref name="H_16_6_16-95_16-96">Cote (2008), ch. 16.6, pp. 16-95–16-96.</ref>


A wet system contains water up to the closed sprinklers. A dry system contains pressurised gas downstream of a valve, so sprinkler operation first initiates pressure decay and valve release. Water must then travel through the piping. A preaction arrangement adds a detection-controlled release condition whose logic depends on the particular system. <ref name="H_16_3_16-34_16-38">Cote (2008), ch. 16.3, pp. 16-34–16-38.</ref><ref name="F_4-72_4-73_4-85" />
A wet system contains water up to the closed sprinklers; a dry system contains pressurised gas downstream of a valve, so sprinkler operation first initiates pressure decay and valve release. Water must then travel through the piping. A preaction arrangement adds a detection-controlled release condition whose logic depends on the particular system. <ref name="H_16_3_16-34_16-38">Cote (2008), ch. 16.3, pp. 16-34–16-38.</ref><ref name="F_4-72_4-73_4-85" />


Fleming separates dry-system water delivery into valve trip time and water transit time. A quicker release can reduce the first component without eliminating the second. The number and location of open sprinklers affect gas venting and water travel. Consequently, a remote test gives a defined comparison condition, rather than reproducing every possible fire sequence. <ref name="F_4-85" />
Fleming separates dry-system water delivery into valve trip time and water transit time; a quicker release can reduce the first component without eliminating the second. The number and location of open sprinklers affect gas venting and water travel. Consequently, a remote test gives a defined comparison condition, rather than reproducing every possible fire sequence. <ref name="F_4-85" />


The IFEG analysis process likewise distinguishes local activation conditions, notification delays and the effect of suppression. Its 2005 framework treats these as inputs to an evolving fire scenario. A detector signal cannot by itself establish that water has reached the burning material. That distinction matters whenever the fire model changes growth behaviour at an assumed intervention time. <ref name="I_1_7-4_1_7-8">National Research Council of Canada et al. (2005), pp. 1.7-4–1.7-8.</ref>
The IFEG analysis process likewise distinguishes local activation conditions, notification delays and the effect of suppression; its 2005 framework treats these as inputs to an evolving fire scenario. A detector signal cannot by itself establish that water has reached the burning material. That distinction matters whenever the fire model changes growth behaviour at an assumed intervention time. <ref name="I_1_7-4_1_7-8">National Research Council of Canada et al. (2005), pp. 1.7-4–1.7-8.</ref>


== Storage height and sprinkler clearance ==
== Storage height and sprinkler clearance ==
Storage height measures the vertical extent of the goods, while clearance describes the gap between the top of storage and the sprinkler region. They are related but distinct design inputs. Increasing storage height changes the quantity and arrangement of burning fuel below the sprinkler. Changing clearance alters the distance over which heat and water must travel. <ref name="H_16_5_16-78_16-79">Cote (2008), ch. 16.5, pp. 16-78–16-79.</ref>
Storage height measures the vertical extent of the goods, while clearance describes the gap between the top of storage and the sprinkler region; they are related but distinct design inputs. Increasing storage height changes the quantity and arrangement of burning fuel below the sprinkler. Changing clearance alters the distance over which heat and water must travel. <ref name="H_16_5_16-78_16-79">Cote (2008), ch. 16.5, pp. 16-78–16-79.</ref>


The handbook associates higher storage with a more severe fire at sprinkler operation. A greater clearance can delay operation and allow a larger plume to develop above the goods. That plume can make it harder for water to reach the burning material. A low stack under a very high ceiling is therefore not automatically a less demanding sprinkler case. <ref name="H_16_5_16-78_16-79" />
The handbook associates higher storage with a more severe fire at sprinkler operation; a greater clearance can delay operation and allow a larger plume to develop above the goods. That plume can make it harder for water to reach the burning material. A low stack under a very high ceiling is therefore not automatically a less demanding sprinkler case. <ref name="H_16_5_16-78_16-79" />


A minimum clearance serves a different purpose from a maximum tested clearance. Space below the deflector allows the intended spray pattern to develop. An excessive distance above storage can create difficulties in thermal response and plume penetration. These two limits address different mechanisms and should not be collapsed into one rule that more empty space is always beneficial. <ref name="H_16_5_16-79">Cote (2008), ch. 16.5, pp. 16-79.</ref>
A minimum clearance serves a different purpose from a maximum tested clearance; space below the deflector allows the intended spray pattern to develop. An excessive distance above storage can create difficulties in thermal response and plume penetration. These two limits address different mechanisms and should not be collapsed into one rule that more empty space is always beneficial. <ref name="H_16_5_16-79">Cote (2008), ch. 16.5, p. 16-79.</ref>


The 2008 handbook discusses United States NFPA 13 criteria that depend on sprinkler technology and the storage arrangement. It explains that ceiling height becomes a direct input in specific-application and suppression-mode protection tables. Those criteria preserve the conditions of the relevant tests. Their historical numerical limits are not general properties of every sprinkler carrying the same broad name. <ref name="H_16_5_16-79_16-83" />
The 2008 handbook discusses United States NFPA 13 criteria that depend on sprinkler technology and the storage arrangement; it explains that ceiling height becomes a direct input in specific-application and suppression-mode protection tables. Those criteria preserve the conditions of the relevant tests. Their historical numerical limits are not general properties of every sprinkler carrying the same broad name. <ref name="H_16_5_16-79_16-83" />


Warehouse stock levels vary through daily and seasonal operations. A design that relies on a favourable low clearance can become inappropriate when goods are removed and the gap increases. Similarly, exceeding an established maximum storage height changes the fire challenge. The operational description therefore needs both the maximum permitted storage and the range of clearances represented in the design. <ref name="H_16_5_16-72_16-79">Cote (2008), ch. 16.5, pp. 16-72,16-79.</ref>
Warehouse stock levels vary through daily and seasonal operations; a design that relies on a favourable low clearance can become inappropriate when goods are removed and the gap increases. Similarly, exceeding an established maximum storage height changes the fire challenge. The operational description therefore needs both the maximum permitted storage and the range of clearances represented in the design. <ref name="H_16_5_16-72_16-79">Cote (2008), ch. 16.5, pp. 16-72,16-79.</ref>


Thermal-response calculation alone does not settle these questions. Fleming describes limitations associated with orientation, conduction and the element's location relative to the ceiling. Even an accurate activation estimate leaves the subsequent delivery and water penetration to be assessed. Storage protection criteria bring these effects together through a defined application rather than a single height formula. <ref name="F_4-85_4-87" /><ref name="H_16_5_16-79_16-84" />
Thermal-response calculation alone does not settle these questions; Fleming describes limitations associated with orientation, conduction and the element's location relative to the ceiling. Even an accurate activation estimate leaves the subsequent delivery and water penetration to be assessed. Storage protection criteria bring these effects together through a defined application rather than a single height formula. <ref name="F_4-85_4-87" /><ref name="H_16_5_16-79_16-84" />


== Tested applications and system boundaries ==
== Tested applications and system boundaries ==
A sprinkler's hydraulic coefficient is only one of its defining properties. Its orientation, temperature rating, thermal sensitivity and distribution pattern also affect performance. Special sprinklers are developed and evaluated for particular arrangements. Matching one property does not establish that another model can serve the same application. <ref name="H_16_2_16-17_16-27">Cote (2008), ch. 16.2, pp. 16-17–16-27.</ref><ref name="F_4-72_4-75" />
A sprinkler's hydraulic coefficient is only one of its defining properties; its orientation, temperature rating, thermal sensitivity and distribution pattern also affect performance. Special sprinklers are developed and evaluated for particular arrangements. Matching one property does not establish that another model can serve the same application. <ref name="H_16_2_16-17_16-27">Cote (2008), ch. 16.2, pp. 16-17–16-27.</ref><ref name="F_4-72_4-75" />


The term listing refers here to the conditions under which equipment has been evaluated for its intended use. Those conditions can include installation position, permitted coverage, pressure and construction details. The handbook repeatedly links special sprinkler performance to these conditions. A larger orifice or faster element alone does not reproduce an established application. <ref name="H_16_2_16-23_16-27" /><ref name="H_16_5_16-80" />
The term listing refers here to the conditions under which equipment has been evaluated for its intended use; those conditions can include installation position, permitted coverage, pressure and construction details. The handbook repeatedly links special sprinkler performance to these conditions. A larger orifice or faster element alone does not reproduce an established application. <ref name="H_16_2_16-23_16-27_29cadfc7" /><ref name="H_16_5_16-80" />


The distinction is particularly clear for control-mode specific-application and early-suppression fast-response sprinklers. Their discharge criteria use specified operating sprinklers and minimum pressure for the relevant arrangement. Conventional density-area calculations use a different basis. Moving numerical values between these methods can remove the fire-test assumptions that gave the values meaning. <ref name="H_16_5_16-79_16-83" />
The distinction is particularly clear for control-mode specific-application and early-suppression fast-response sprinklers; their discharge criteria use specified operating sprinklers and minimum pressure for the relevant arrangement. Conventional density-area calculations use a different basis. Moving numerical values between these methods can remove the fire-test assumptions that gave the values meaning. <ref name="H_16_5_16-79_16-83" />


System type also forms part of the boundary. A wet system delivers water differently from a dry or detection-controlled arrangement. Delays, gas evacuation and release logic can change the fire before useful water discharge begins. A criterion developed for one arrangement cannot be presumed valid for another merely because both use the same sprinkler body. <ref name="H_16_3_16-34_16-38" /><ref name="F_4-85" />
System type also forms part of the boundary; a wet system delivers water differently from a dry or detection-controlled arrangement. Delays, gas evacuation and release logic can change the fire before useful water discharge begins. A criterion developed for one arrangement cannot be presumed valid for another merely because both use the same sprinkler body. <ref name="H_16_3_16-34_16-38" /><ref name="F_4-85" />


The United States NFPA provisions discussed in the 2008 handbook belong to the editions and development history reported there. Fleming's SFPE chapter was published in 2002 and describes an earlier stage of the standards. These sources explain the engineering basis and historical criteria. They do not establish which edition a present jurisdiction has adopted. <ref name="H_16_3_16-33">Cote (2008), ch. 16.3, pp. 16-33.</ref><ref name="F_4-72_4-73">Fleming (2002), ch. 4-3, pp. 4-72–4-73.</ref>
The United States NFPA provisions discussed in the 2008 handbook belong to the editions and development history reported there. Fleming's SFPE chapter was published in 2002 and describes an earlier stage of the standards. These sources explain the engineering basis and historical criteria. They do not establish which edition a present jurisdiction has adopted. <ref name="H_16_3_16-33">Cote (2008), ch. 16.3, p. 16-33.</ref><ref name="F_4-72_4-73">Fleming (2002), ch. 4-3, pp. 4-72–4-73.</ref>


This distinction also affects replacement and alteration. A substitute needs the performance characteristics relevant to the installation, while changes to storage or construction may require a different design basis. Maintenance preserves an existing function; a changed hazard raises a design question. Inspection records therefore need to identify both the equipment and the conditions it is intended to protect. <ref name="H_16_11_16-205_16-210">Cote (2008), ch. 16.11, pp. 16-205–16-210.</ref><ref name="H_16_5_16-72">Cote (2008), ch. 16.5, pp. 16-72.</ref>
This distinction also affects replacement and alteration; a substitute needs the performance characteristics relevant to the installation, while changes to storage or construction may require a different design basis. Maintenance preserves an existing function; a changed hazard raises a design question. Inspection records therefore need to identify both the equipment and the conditions it is intended to protect. <ref name="H_16_11_16-205_16-210">Cote (2008), ch. 16.11, pp. 16-205–16-210.</ref><ref name="H_16_5_16-72">Cote (2008), ch. 16.5, p. 16-72.</ref>


== See also ==
== See also ==

Latest revision as of 00:40, 16 November 2026

Control mode specific application sprinkler is a sprinkler whose fire-control performance is established for specified applications using defined sprinkler-count and minimum-pressure criteria. [1][2] The abbreviation CMSA identifies a design approach that differs from conventional density-area protection and from suppression-mode protection. Orifice and deflector design improve discharge characteristics for the intended challenge. The relevant commodity, arrangement, height and system conditions remain part of the application. [1]

Sprinkler performance combines thermal operation, timely water delivery and an effective discharge pattern. These functions are related, but evidence for one does not establish all the others. The protected hazard and the installed geometry remain part of the design basis. Hydraulic calculations establish delivery under stated assumptions, while the suitability of those assumptions depends on the application and the supporting fire-performance evidence. [3][4] Heat access and water access can be obstructed separately. [5]

Specific-application control criteria

The sprinkler head is selected as part of a tested protection method for a warehouse fire scenario; the large-drop sprinkler was an early example described by the handbook. Later devices can have different orifices and application limits. The common CMSA label does not make those devices interchangeable across every permitted storage arrangement. [6]

Control mode specific application sprinkler: functional relationships. Mechanism and application limits are distinguished.
Control mode specific application sprinkler: functional relationships. Schematic explanation; dimensions are not installation instructions.

Fire control and fire suppression describe different intended outcomes; an ESFR sprinkler uses another protection approach intended for early suppression, while CMSA remains a control-mode designation. Rack storage can be protected through different established combinations of ceiling and in-rack equipment. Selection depends on the complete arrangement rather than the perceived superiority of one broad label. [7]

The minimum pressure in a specific-application table is not reduced simply by reducing the assigned area per sprinkler; that differs from the arithmetic of a conventional density-area design. A sprinkler-count criterion also defines the operating demand differently from a nominal floor area. Preserving this distinction prevents a hydraulic redesign from inadvertently changing the underlying fire-performance basis. [1]

Selecting a storage protection method

The handbook distinguishes control-mode density-area, control-mode specific-application and suppression-mode sprinkler protection; these are different design approaches with different equipment and criteria. A similar nominal flow does not make their fire performance interchangeable. The selected method must match the commodity, storage arrangement and building conditions. [8]

Three protection methods. Mechanism and application limits are distinguished.
Three protection methods. Schematic explanation; dimensions are not installation instructions.

Density-area protection specifies an application density over an operating area; the assigned coverage of each sprinkler then determines its minimum flow and associated pressure. Actual network calculation accounts for pressure differences among the operating sprinklers. Ceiling-only arrangements and arrangements with in-rack sprinklers have different demands and protection assumptions. [9][10]

Specific-application protection instead uses a specified number of sprinklers at a minimum pressure for a tested arrangement; the handbook identifies the large-drop sprinkler as an early example of this approach. Later designs use other orifice and deflector combinations. Permission for one type in a particular storage arrangement does not establish suitability of another type. [1]

Early-suppression fast-response sprinklers combine rapid thermal response with a high-volume discharge intended to suppress the developing storage fire; their benefit does not arise from sensitivity alone. Water momentum, distribution, ceiling geometry and installation conditions form part of the method. An ordinary quick-response sprinkler therefore cannot be assumed to provide the same protection. [1][11]

In-rack protection offers another means of placing water near shielded fuel; it can reduce the challenge that reaches the ceiling by controlling local spread. However, rack piping and sprinklers can be exposed to mechanical damage during materials handling. Their arrangement and continued condition are part of the protection strategy, rather than an optional addition to an unchanged ceiling calculation. [12]

The water supply must support the selected combination of ceiling sprinklers, in-rack sprinklers and applicable hose demand for the specified duration. Hydraulic adequacy does not establish that a different storage configuration will be controlled. Fleming separates delivery calculations from fire-performance evidence for this reason. The complete design preserves both the hydraulic requirements and the tested application boundaries. [13][2]

Water distribution and fire performance

Water can influence a fire by cooling burning material, wetting nearby fuel and absorbing heat from hot gases; the relative importance of these mechanisms depends on the sprinkler and the fire arrangement. Water discharged at the ceiling is not necessarily water delivered to the burning surface. Upward gas movement and intervening objects can redirect or prevent delivery. [14][15]

Water reaching the fire. Mechanism and application limits are distinguished.
Water reaching the fire. Schematic explanation; dimensions are not installation instructions.

Droplet size creates a physical trade-off; smaller droplets expose more surface area for a given volume of water and can exchange heat rapidly. Larger droplets can have greater ability to penetrate an upward-moving plume. Effective sprinkler design considers momentum, distribution and the intended fire challenge together, rather than maximising one characteristic in isolation. [16][17]

Pressure and orifice geometry influence spray formation; a higher discharge pressure does not simply spread a fixed amount of water more effectively over every protected surface. The handbook describes changes in droplet behaviour and warns against assuming that increased pressure always improves coverage. The resulting pattern belongs to a specified sprinkler operating within its intended conditions. [18][19]

The distinction between floor-area density and water reaching fuel is particularly important in storage; a nominal density describes a design quantity over an assigned area. Actual delivered water can be obstructed by shelves, packaging or the geometry of the goods. The critical application rate at a burning surface is therefore not automatically the same number as the nominal sprinkler design density. [20][21]

Control limits the growth or spread of a fire sufficiently for the intended protection objective; suppression involves a stronger reduction in burning, while complete extinguishment means that combustion has ceased. The handbook describes different sprinkler technologies developed around these objectives. A successfully operating sprinkler does not establish which outcome has occurred without considering the fire and water interaction. [22][23]

The International Fire Engineering Guidelines (IFEG) illustrates possible design-fire outcomes as continued growth, control or extinguishment; a steady heat-release rate after activation is a modelling representation of control, not a universal measured sprinkler response. A decay curve likewise requires an appropriate basis. Fleming's discussion of furnishing-fire suppression models identifies fuel and test limitations that prevent unrestricted transfer to shielded warehouse fires. [24][25]

Discharge, pressure and assigned area

Hydraulic calculation starts with the water discharge required at an individual operating sprinkler; in a density-area design, the assigned area and selected application density determine that minimum discharge. The assigned area comes from the spacing method used for the design. It is not an assertion that every point beneath the sprinkler receives an identical local quantity. [26][14]

The discharge coefficient, or K-factor, relates flow to the square root of pressure at the sprinkler; its numerical value depends on the units used for both quantities. A value stated for pressure in bar cannot be inserted unchanged when pressure is in kilopascals. The unit convention is part of the coefficient's definition. [27][28]

q=dAs=Kp,p=(qK)2

Symbol Description Unit
q Required sprinkler flow L/min
d,As Design density and assigned area L/(min·m²); m²
p Sprinkler discharge pressure kPa
K Discharge coefficient in this convention L/(min·√kPa)

Using the rounded metric inputs in Fleming's example, 6.1 L/(min·m²) over 15.6 m² requires 95.2 L/min. With a nominal K-factor of 8.0 L/(min·√kPa), the calculated pressure is approximately 142 kPa. The corresponding bar-based K-factor is 80 L/(min·√bar). The example illustrates the calculation method, rather than selecting a density for a new hazard. [28][27]

Other sprinklers in the operating area may have greater pressure than the limiting sprinkler; their individual discharges then exceed the minimum flow calculated from density and coverage alone. Total demand is the sum of those actual calculated flows, with applicable additional demands considered separately. Simply multiplying nominal density by nominal design area can therefore understate the hydraulic result. [29][30]

A higher K-factor reduces the pressure required for a specified flow; it does not establish a particular spray pattern, response sensitivity or suitability for storage. Those characteristics depend on the complete sprinkler design and its tested application. Hydraulic equivalence is therefore narrower than equivalent fire protection performance. [31][6]

Thermal operation and water delivery

An automatic sprinkler combines a heat-responsive element with a water-distribution device; the element responds to its own temperature, which follows the surrounding gas conditions with a delay. Water then needs an open discharge path and an adequate supply. These are successive physical processes, so activation time and effective water delivery are not interchangeable quantities. [32][33]

Temperature rating describes the nominal operating temperature established under specified test conditions; thermal sensitivity describes how quickly the element heats in a moving hot gas stream. A sprinkler can therefore have the same temperature rating as another device while responding differently to a growing fire. Gas velocity, heat conduction and the element's position beneath the ceiling influence that response. [34][35]

The response time index provides a measure of thermal sensitivity; lower values represent faster response under comparable convective heating conditions. The handbook relates this index to a thermal time constant and the square root of gas velocity. Conduction into the sprinkler frame introduces another influence, especially where convection is weak. [36][37]

A wet system contains water up to the closed sprinklers; a dry system contains pressurised gas downstream of a valve, so sprinkler operation first initiates pressure decay and valve release. Water must then travel through the piping. A preaction arrangement adds a detection-controlled release condition whose logic depends on the particular system. [38][32]

Fleming separates dry-system water delivery into valve trip time and water transit time; a quicker release can reduce the first component without eliminating the second. The number and location of open sprinklers affect gas venting and water travel. Consequently, a remote test gives a defined comparison condition, rather than reproducing every possible fire sequence. [35]

The IFEG analysis process likewise distinguishes local activation conditions, notification delays and the effect of suppression; its 2005 framework treats these as inputs to an evolving fire scenario. A detector signal cannot by itself establish that water has reached the burning material. That distinction matters whenever the fire model changes growth behaviour at an assumed intervention time. [39]

Storage height and sprinkler clearance

Storage height measures the vertical extent of the goods, while clearance describes the gap between the top of storage and the sprinkler region; they are related but distinct design inputs. Increasing storage height changes the quantity and arrangement of burning fuel below the sprinkler. Changing clearance alters the distance over which heat and water must travel. [40]

The handbook associates higher storage with a more severe fire at sprinkler operation; a greater clearance can delay operation and allow a larger plume to develop above the goods. That plume can make it harder for water to reach the burning material. A low stack under a very high ceiling is therefore not automatically a less demanding sprinkler case. [40]

A minimum clearance serves a different purpose from a maximum tested clearance; space below the deflector allows the intended spray pattern to develop. An excessive distance above storage can create difficulties in thermal response and plume penetration. These two limits address different mechanisms and should not be collapsed into one rule that more empty space is always beneficial. [41]

The 2008 handbook discusses United States NFPA 13 criteria that depend on sprinkler technology and the storage arrangement; it explains that ceiling height becomes a direct input in specific-application and suppression-mode protection tables. Those criteria preserve the conditions of the relevant tests. Their historical numerical limits are not general properties of every sprinkler carrying the same broad name. [8]

Warehouse stock levels vary through daily and seasonal operations; a design that relies on a favourable low clearance can become inappropriate when goods are removed and the gap increases. Similarly, exceeding an established maximum storage height changes the fire challenge. The operational description therefore needs both the maximum permitted storage and the range of clearances represented in the design. [42]

Thermal-response calculation alone does not settle these questions; Fleming describes limitations associated with orientation, conduction and the element's location relative to the ceiling. Even an accurate activation estimate leaves the subsequent delivery and water penetration to be assessed. Storage protection criteria bring these effects together through a defined application rather than a single height formula. [15][7]

Tested applications and system boundaries

A sprinkler's hydraulic coefficient is only one of its defining properties; its orientation, temperature rating, thermal sensitivity and distribution pattern also affect performance. Special sprinklers are developed and evaluated for particular arrangements. Matching one property does not establish that another model can serve the same application. [43][2]

The term listing refers here to the conditions under which equipment has been evaluated for its intended use; those conditions can include installation position, permitted coverage, pressure and construction details. The handbook repeatedly links special sprinkler performance to these conditions. A larger orifice or faster element alone does not reproduce an established application. [31][6]

The distinction is particularly clear for control-mode specific-application and early-suppression fast-response sprinklers; their discharge criteria use specified operating sprinklers and minimum pressure for the relevant arrangement. Conventional density-area calculations use a different basis. Moving numerical values between these methods can remove the fire-test assumptions that gave the values meaning. [8]

System type also forms part of the boundary; a wet system delivers water differently from a dry or detection-controlled arrangement. Delays, gas evacuation and release logic can change the fire before useful water discharge begins. A criterion developed for one arrangement cannot be presumed valid for another merely because both use the same sprinkler body. [38][35]

The United States NFPA provisions discussed in the 2008 handbook belong to the editions and development history reported there. Fleming's SFPE chapter was published in 2002 and describes an earlier stage of the standards. These sources explain the engineering basis and historical criteria. They do not establish which edition a present jurisdiction has adopted. [44][45]

This distinction also affects replacement and alteration; a substitute needs the performance characteristics relevant to the installation, while changes to storage or construction may require a different design basis. Maintenance preserves an existing function; a changed hazard raises a design question. Inspection records therefore need to identify both the equipment and the conditions it is intended to protect. [46][47]

See also

Notes

  1. ↑ 1.0 1.1 1.2 1.3 1.4 Cote (2008), ch. 16.5, pp. 16-80–16-83.
  2. ↑ 2.0 2.1 2.2 Fleming (2002), ch. 4-3, pp. 4-72–4-75.
  3. ↑ Fleming (2002), ch. 4-3, pp. 4-72–4-75,4-85–4-87.
  4. ↑ Cote (2008), ch. 16.1, pp. 16-4–16-9.
  5. ↑ Cote (2008), ch. 16.3, pp. 16-45–16-47.
  6. ↑ 6.0 6.1 6.2 Cote (2008), ch. 16.5, p. 16-80.
  7. ↑ 7.0 7.1 Cote (2008), ch. 16.5, pp. 16-79–16-84.
  8. ↑ 8.0 8.1 8.2 Cote (2008), ch. 16.5, pp. 16-79–16-83.
  9. ↑ Cote (2008), ch. 16.5, pp. 16-80–16-81.
  10. ↑ Fleming (2002), ch. 4-3, pp. 4-74–4-80.
  11. ↑ Cote (2008), ch. 16.2, p. 16-27.
  12. ↑ Cote (2008), ch. 16.5, pp. 16-77,16-80,16-84.
  13. ↑ Cote (2008), ch. 16.5, pp. 16-85–16-86.
  14. ↑ 14.0 14.1 Cote (2008), ch. 16.1, pp. 16-6–16-8.
  15. ↑ 15.0 15.1 Fleming (2002), ch. 4-3, pp. 4-85–4-87.
  16. ↑ Cote (2008), ch. 16.1, pp. 16-6–16-9.
  17. ↑ Cote (2008), ch. 16.2, pp. 16-23,16-27.
  18. ↑ Cote (2008), ch. 16.1, p. 16-6.
  19. ↑ Cote (2008), ch. 16.5, p. 16-85.
  20. ↑ Cote (2008), ch. 16.1, pp. 16-7–16-8.
  21. ↑ Cote (2008), ch. 16.5, pp. 16-74–16-84.
  22. ↑ Cote (2008), ch. 16.3, p. 16-38.
  23. ↑ Cote (2008), ch. 16.5, pp. 16-79–16-80.
  24. ↑ National Research Council of Canada et al. (2005), p. 1.7-7.
  25. ↑ Fleming (2002), ch. 4-3, pp. 4-86–4-87.
  26. ↑ Fleming (2002), ch. 4-3, pp. 4-74–4-75.
  27. ↑ 27.0 27.1 Cote (2008), ch. 16.2, pp. 16-25–16-26.
  28. ↑ 28.0 28.1 Fleming (2002), ch. 4-3, p. 4-75.
  29. ↑ Cote (2008), ch. 16.3, pp. 16-48–16-49.
  30. ↑ Fleming (2002), ch. 4-3, pp. 4-75–4-80.
  31. ↑ 31.0 31.1 Cote (2008), ch. 16.2, pp. 16-23–16-27.
  32. ↑ 32.0 32.1 Fleming (2002), ch. 4-3, pp. 4-72–4-73,4-85.
  33. ↑ Cote (2008), ch. 16.1, pp. 16-4–16-6.
  34. ↑ Cote (2008), ch. 16.2, pp. 16-17–16-18.
  35. ↑ 35.0 35.1 35.2 Fleming (2002), ch. 4-3, p. 4-85.
  36. ↑ Cote (2008), ch. 16.1, pp. 16-4–16-5.
  37. ↑ Cote (2008), ch. 16.6, pp. 16-95–16-96.
  38. ↑ 38.0 38.1 Cote (2008), ch. 16.3, pp. 16-34–16-38.
  39. ↑ National Research Council of Canada et al. (2005), pp. 1.7-4–1.7-8.
  40. ↑ 40.0 40.1 Cote (2008), ch. 16.5, pp. 16-78–16-79.
  41. ↑ Cote (2008), ch. 16.5, p. 16-79.
  42. ↑ Cote (2008), ch. 16.5, pp. 16-72,16-79.
  43. ↑ Cote (2008), ch. 16.2, pp. 16-17–16-27.
  44. ↑ Cote (2008), ch. 16.3, p. 16-33.
  45. ↑ Fleming (2002), ch. 4-3, pp. 4-72–4-73.
  46. ↑ Cote (2008), ch. 16.11, pp. 16-205–16-210.
  47. ↑ Cote (2008), ch. 16.5, p. 16-72.

References

  • Cote, A. E. (Ed.). (2008). Fire protection handbook (20th ed.). National Fire Protection Association.
  • Fleming, R. P. (2002). Automatic sprinkler system calculations. In P. J. DiNenno (Ed.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-72–4-87). National Fire Protection Association.
  • National Research Council of Canada, International Code Council, Department of Building and Housing, & Australian Building Codes Board. (2005). International fire engineering guidelines. Australian Building Codes Board.