New FSE wiki article: Vapour density (written by Claude Opus 5.5) |
Remove bibliographic source lines from image captions and descriptions |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 66: | Line 66: | ||
'''Propane and air at the lower flammable limit.''' The lower flammable limit of propane is 2.15 percent by volume.<ref name="Lemoff-6-183" /> Applying the mixture rule to this concentration gives a density ratio of 0.0215 × 1.50 + 0.9785 × 1, or about 1.01.<ref name="Slye-6-199" /><ref name="Lemoff-6-183" /> At the upper limit of 9.60 percent, the ratio is about 1.05. A propane mixture within its [[flammability limits]] is thus at most a few percent heavier than air. This explains Lemoff's remark that the density of the gas itself matters less in structures than its pure vapour density suggests.<ref name="Lemoff-6-175" /> | '''Propane and air at the lower flammable limit.''' The lower flammable limit of propane is 2.15 percent by volume.<ref name="Lemoff-6-183" /> Applying the mixture rule to this concentration gives a density ratio of 0.0215 × 1.50 + 0.9785 × 1, or about 1.01.<ref name="Slye-6-199" /><ref name="Lemoff-6-183" /> At the upper limit of 9.60 percent, the ratio is about 1.05. A propane mixture within its [[flammability limits]] is thus at most a few percent heavier than air. This explains Lemoff's remark that the density of the gas itself matters less in structures than its pure vapour density suggests.<ref name="Lemoff-6-175" /> | ||
[[File:fse-vapour-density-v3.svg|thumb|upright=1.5|alt=Line chart of mixture density relative to air against vapour concentration for propane and gasoline, with flammable ranges shaded.|Density of vapour and air mixtures relative to air. Within their flammable ranges, propane mixtures are at most about 5 percent and gasoline mixtures about 18 percent heavier than air.]] | |||
'''Cold methane after an LNG spill.''' Methane boils at −161.5 °C, or 111.65 K.<ref name="Drysdale-2-6" /> At that temperature, an ideal-gas estimate of its density relative to air at 20 °C is (16/29) × (293.15/111.65), or about 1.45.<ref name="Drysdale-2-9" /> This agrees with Lemoff, who states that LNG vapour near its normal boiling point is about 1.5 times as heavy as air at 21 °C.<ref name="Lemoff-6-182">Lemoff (2008), p. 6-182.</ref> | '''Cold methane after an LNG spill.''' Methane boils at −161.5 °C, or 111.65 K.<ref name="Drysdale-2-6" /> At that temperature, an ideal-gas estimate of its density relative to air at 20 °C is (16/29) × (293.15/111.65), or about 1.45.<ref name="Drysdale-2-9" /> This agrees with Lemoff, who states that LNG vapour near its normal boiling point is about 1.5 times as heavy as air at 21 °C.<ref name="Lemoff-6-182">Lemoff (2008), p. 6-182.</ref> | ||
For pure methane in air at 20 °C, the same ideal-gas estimate places neutral buoyancy near −111 °C. Rivkin reports about −118 °C for an LNG vapour cloud in air at 16 °C.<ref name="Drysdale-2-9" /><ref name="Rivkin-21-58">Rivkin (2008b), p. 21-58.</ref> These are approximate thresholds because the released gas is a mixture and vapours near their boiling points deviate from ideal behaviour.<ref name="Drysdale-2-9" /><ref name="Rivkin-21-58" /> | |||
'''Halon 1301 in a flooded room.''' With DiNenno's values, a 5 percent Halon 1301 concentration gives a mixture density of 6.283 × 0.05 + 1.202 × 0.95, or about 1.46 kg/m³. This is about 21 percent more than the density of air.<ref name="DiNenno-4-198" /> Grant notes that Halon 1301 vapour is about 5 times heavier than air, so it typically escapes through openings low in a totally flooded volume.<ref name="Grant-4-152">Grant (2002), p. 4-152.</ref> | '''Halon 1301 in a flooded room.''' With DiNenno's values, a 5 percent Halon 1301 concentration gives a mixture density of 6.283 × 0.05 + 1.202 × 0.95, or about 1.46 kg/m³. This is about 21 percent more than the density of air.<ref name="DiNenno-4-198" /> Grant notes that Halon 1301 vapour is about 5 times heavier than air, so it typically escapes through openings low in a totally flooded volume.<ref name="Grant-4-152">Grant (2002), p. 4-152.</ref> | ||
| Line 107: | Line 110: | ||
The table shows that most flammable liquids produce vapours heavier than air. Slye states this directly for gasoline and almost all other flammable liquids.<ref name="Slye-6-207">Slye (2008), p. 6-207.</ref> Kingsbaker gives hexane solvent vapour as about three times heavier than air.<ref name="Kingsbaker-9-135">Kingsbaker (2008), p. 9-135.</ref> | The table shows that most flammable liquids produce vapours heavier than air. Slye states this directly for gasoline and almost all other flammable liquids.<ref name="Slye-6-207">Slye (2008), p. 6-207.</ref> Kingsbaker gives hexane solvent vapour as about three times heavier than air.<ref name="Kingsbaker-9-135">Kingsbaker (2008), p. 9-135.</ref> | ||
[[File:fse-vapour-density-v1.svg|thumb|upright=1.5|alt=Dot chart of vapour density relative to air for 14 gases and vapours, from hydrogen at 0.07 to Halon 1301 at about 5, with a line at air = 1.|Vapour density relative to air (air = 1) of common gases and vapours. Only a few gases, such as hydrogen and methane, are lighter than air.]] | |||
Among the common gases, only a few are much lighter than air. Hydrogen, natural gas and methane rise and disperse quickly at normal temperatures.<ref name="Rivkin-21-58" | Among the common gases, only a few are much lighter than air. Hydrogen, natural gas and methane rise and disperse quickly at normal temperatures.<ref name="Rivkin-21-58" /><ref name="Rivkin-21-59" /> Acetylene and ethylene are only slightly lighter than air, so acetylene does not readily dissipate.<ref name="Lemoff-6-178">Lemoff (2008), p. 6-178.</ref><ref name="Lemoff-6-181">Lemoff (2008), p. 6-181.</ref> Carbon monoxide is so close to air that it mixes readily with any air movement.<ref name="Black-14-115">Black (2008), p. 14-115.</ref> | ||
== Behaviour of released vapours == | == Behaviour of released vapours == | ||
Heavy vapours settle. Slye explains that they settle on floors or in pits and depressions and may flow along the floor or ground for long distances. They can then be ignited at a remote point and flash back to the source.<ref name="Slye-6-207" /> The extra density of a heavy vapour can even make vapour from a spill travel upwind to unprotected ignition sources.<ref name="Slye-6-199" /> Drysdale describes how propane leaking slowly from a cylinder accumulates and spreads at ground level with little dilution, which is a serious hazard in a basement or a poorly ventilated boat.<ref name="Drysdale-2-5" /><ref name="Drysdale-2-6" /> | Heavy vapours settle. Slye explains that they settle on floors or in pits and depressions and may flow along the floor or ground for long distances. They can then be ignited at a remote point and flash back to the source.<ref name="Slye-6-207" /> The extra density of a heavy vapour can even make vapour from a spill travel upwind to unprotected ignition sources.<ref name="Slye-6-199" /> Drysdale describes how propane leaking slowly from a cylinder accumulates and spreads at ground level with little dilution, which is a serious hazard in a basement or a poorly ventilated boat.<ref name="Drysdale-2-5" /><ref name="Drysdale-2-6" /> | ||
Releases of [[liquefied petroleum gas]] show this behaviour on a larger scale. Rivkin states that propane, with a vapour density of 1.5, sinks to the ground and forms a vapour cloud that follows surface contours over a large area.<ref name="Rivkin-21-59" /> Even outdoors such a cloud can travel downwind at flammable concentrations until it meets an ignition source.<ref name="Rivkin-21-67">Rivkin (2008b), p. 21-67.</ref> LP-gas | Releases of [[liquefied petroleum gas]] show this behaviour on a larger scale. Rivkin states that propane, with a vapour density of 1.5, sinks to the ground and forms a vapour cloud that follows surface contours over a large area.<ref name="Rivkin-21-59" /> Even outdoors such a cloud can travel downwind at flammable concentrations until it meets an ignition source.<ref name="Rivkin-21-67">Rivkin (2008b), p. 21-67.</ref> At comparable temperatures, LP-gas vapour remains heavier than air because of its greater molecular weight; a hot plume or fast jet can behave differently.<ref name="Rivkin-21-74">Rivkin (2008b), p. 21-74.</ref><ref name="Drysdale-2-5" /><ref name="Lemoff-6-184">Lemoff (2008), p. 6-184.</ref> Ignition of a large outdoor cloud under conditions that promote rapid flame speeds can lead to a [[vapour cloud explosion]]. Zalosh names propane, propylene, ethylene and various aromatic hydrocarbons among the vapours often involved.<ref name="Zalosh-2-104">Zalosh (2008), p. 2-104.</ref> | ||
Light gases behave differently but are not harmless. Natural gas, with a vapour density below 1, rises at ambient conditions. Methane, at about 0.6, can pool under a ceiling in an enclosed space, where light fixtures and air-handling equipment may ignite it.<ref name="Rivkin-21-58" /> In an enclosed area methane can create an explosion hazard very rapidly.<ref name="Drysdale-2-6" /> | Light gases behave differently but are not harmless. Natural gas, with a vapour density below 1, rises at ambient conditions. Methane, at about 0.6, can pool under a ceiling in an enclosed space, where light fixtures and air-handling equipment may ignite it.<ref name="Rivkin-21-58" /> In an enclosed area methane can create an explosion hazard very rapidly.<ref name="Drysdale-2-6" /> | ||
Cold releases form a third group. Lemoff explains that gas produced near the source of an evaporating liquefied gas | Cold releases form a third group. Lemoff explains that gas produced near the source of an evaporating liquefied gas can be heavier than ambient air because it is cold. Even normally lighter gases can therefore hug the ground near the source, accompanied by a visible water fog.<ref name="Lemoff-6-176" /> LNG vapour near its boiling point is about 1.5 times heavier than air and spreads along the ground with such a fog.<ref name="Lemoff-6-182" /> Rivkin adds that LNG vapour eventually becomes buoyant. At night it takes longer for the vapour to warm, so a flammable puff can travel farther.<ref name="Rivkin-21-59" /><ref name="Rivkin-21-74" /> | ||
[[File:fse-vapour-density-v4.svg|thumb|upright=1.5|alt=Side view of an LNG pool with cold vapour and fog spreading along the ground, warming downwind and finally rising as buoyant methane.|Near its boiling point, vapour from a spill of liquefied natural gas is about 1.5 times as heavy as air, so it spreads along the ground with a visible fog. As it warms it becomes lighter than air and rises.]] | |||
Carbon dioxide used for extinguishment is 1.5 times as dense as air at the same temperature. Its cold discharge is much denser still, which lets it replace air above burning surfaces.<ref name="Wysocki-17-4">Wysocki (2008), p. 17-4.</ref> When carbon dioxide is used for total flooding, the mixture of carbon dioxide and air is denser than the surrounding atmosphere.<ref name="Wysocki-17-4" /> | Carbon dioxide used for extinguishment is 1.5 times as dense as air at the same temperature. Its cold discharge is much denser still, which lets it replace air above burning surfaces.<ref name="Wysocki-17-4">Wysocki (2008), p. 17-4.</ref> When carbon dioxide is used for total flooding, the mixture of carbon dioxide and air is denser than the surrounding atmosphere.<ref name="Wysocki-17-4" /> | ||
| Line 125: | Line 130: | ||
A [[gas detection system]] also depends on vapour density. Cholin explains that in still air, lighter-than-air gases reach higher concentrations high in a space and heavier-than-air gases low in a space. Specific densities help predict where a leaking gas will go.<ref name="Cholin-14-107" /> Sensors for methane, natural gas and other light gases are generally placed above the gas-containing equipment. Sensors for propane, butane and most vapours are placed low in the hazard area.<ref name="Cholin-14-107" /> For carbon monoxide, whose vapour density is very close to that of air, Black notes that residential detectors can be mounted either on the ceiling or on the wall.<ref name="Black-14-115" /> | A [[gas detection system]] also depends on vapour density. Cholin explains that in still air, lighter-than-air gases reach higher concentrations high in a space and heavier-than-air gases low in a space. Specific densities help predict where a leaking gas will go.<ref name="Cholin-14-107" /> Sensors for methane, natural gas and other light gases are generally placed above the gas-containing equipment. Sensors for propane, butane and most vapours are placed low in the hazard area.<ref name="Cholin-14-107" /> For carbon monoxide, whose vapour density is very close to that of air, Black notes that residential detectors can be mounted either on the ceiling or on the wall.<ref name="Black-14-115" /> | ||
[[File:fse-vapour-density-v2.svg|thumb|upright=1.5|alt=Room cross-section: propane vapour spreading along the floor into a pit, methane collecting under the ceiling, with low and high sensors and exhaust openings.|In still air, heavy vapours such as propane collect at floor level and in pits, while light gases such as methane collect under the ceiling. Exhaust openings and gas sensors are placed accordingly.]] | |||
The same reasoning sets the size of hazardous areas. Lemoff and Rivkin state that the vapour density of a stored gas partly determines the extent of the area in which ignition sources should be eliminated or controlled.<ref name="Lemoff-Rivkin-7-41" /> Fuel cell installations using propane need special ventilation because the gas collects in low-lying areas.<ref name="Biggins-8-110">Biggins (2008), p. 8-110.</ref> In building security design, Meacham and Galioto recommend high air intakes because most chemical and biological agents are heavier than air.<ref name="Meacham-1-129">Meacham and Galioto (2008), p. 1-129.</ref> | The same reasoning sets the size of hazardous areas. Lemoff and Rivkin state that the vapour density of a stored gas partly determines the extent of the area in which ignition sources should be eliminated or controlled.<ref name="Lemoff-Rivkin-7-41" /> Fuel cell installations using propane need special ventilation because the gas collects in low-lying areas.<ref name="Biggins-8-110">Biggins (2008), p. 8-110.</ref> In building security design, Meacham and Galioto recommend high air intakes because most chemical and biological agents are heavier than air.<ref name="Meacham-1-129">Meacham and Galioto (2008), p. 1-129.</ref> | ||
== Limits and common misconceptions == | == Limits and common misconceptions == | ||
A vapour density is not a fixed behaviour. It describes the pure vapour at the same temperature and pressure as the air, while real releases are mixtures at other temperatures.<ref name="Slye-6-199" /> Cholin warns that a gas leaking from high pressure cools the air it flows into. The cooled mixture contracts, becomes denser and only slowly returns to ambient temperature.<ref name="Cholin-14-107" /> Wind and air currents also move heavy gases, and the velocity of a pressurised jet release can overcome the effect of density altogether.<ref name="Lemoff-6-184" | A vapour density is not a fixed behaviour. It describes the pure vapour at the same temperature and pressure as the air, while real releases are mixtures at other temperatures.<ref name="Slye-6-199" /> Cholin warns that a gas leaking from high pressure cools the air it flows into. The cooled mixture contracts, becomes denser and only slowly returns to ambient temperature.<ref name="Cholin-14-107" /> Wind and air currents also move heavy gases, and the velocity of a pressurised jet release can overcome the effect of density altogether.<ref name="Lemoff-6-184" /> | ||
A common misconception is that a vapour heavier than air will always stay low. Slye notes that convection currents of heated air or normal diffusion may carry heavy vapours upward.<ref name="Slye-6-207" /> The opposite error is to assume that a light gas cannot accumulate at low level, which cold LNG and hydrogen vapours disprove for some distance from the source.<ref name="Lemoff-6-176" /><ref name="Lemoff-6-182" /> A third error is to read the pure vapour density as the density of a flammable cloud, which is mostly air.<ref name="Lemoff-6-175" /> | A common misconception is that a vapour heavier than air will always stay low. Slye notes that convection currents of heated air or normal diffusion may carry heavy vapours upward.<ref name="Slye-6-207" /> The opposite error is to assume that a light gas cannot accumulate at low level, which cold LNG and hydrogen vapours disprove for some distance from the source.<ref name="Lemoff-6-176" /><ref name="Lemoff-6-182" /> A third error is to read the pure vapour density as the density of a flammable cloud, which is mostly air.<ref name="Lemoff-6-175" /> | ||
Vapour density should also not be confused with vapour pressure. | Vapour density should also not be confused with vapour pressure. Vapour pressure sets the equilibrium vapour concentration above a liquid at a given temperature and total pressure, while vapour density helps predict where a release tends to go.<ref name="Slye-6-199" /> Published values can also disagree. Rivkin gives 0.07 for hydrogen and Biggins 0.1, while Table 14.8.1 of the handbook prints 0.7000.<ref name="Rivkin-21-59" /><ref name="Biggins-8-110" /><ref name="Cholin-14-107" /> Since 2/29 is about 0.07, the ideal-gas ratio supports Rivkin's value.<ref name="Slye-6-199" /> | ||
== See also == | == See also == | ||
Latest revision as of 08:25, 8 November 2026
Vapour density is the mass per unit volume of a pure gas or vapour. In fire protection it is usually given as a ratio: the weight of a volume of vapour divided by the weight of an equal volume of air at the same temperature and pressure.[1] Air is taken as 1, so a vapour density of 3 means that the vapour is three times as heavy as air. The ratio equals the molecular weight of the substance divided by 29, the composite molecular weight of air.[1] The same quantity is also called gas specific gravity or vapour specific gravity.[2][3]
Vapour density indicates whether a released vapour tends to sink or rise. Vapours heavier than air collect in low areas and can travel considerable distances to an ignition source, while lighter ones rise and disperse more readily.[1] Propane, with a vapour density of about 1.5, spreads at ground level, whereas methane at about 0.55 rises at ambient temperature.[4][5] The property guides the placement of ventilation openings and gas detectors and the size of areas where ignition sources are controlled.[6][7][8] It applies strictly only to the pure vapour at the temperature of the surrounding air. Real releases are usually mixtures with air, and cold vapours can behave as heavy gases even when their molecular weight is low.[1][9]
Definition
Slye defines vapour density as the weight per unit volume of a pure gas or vapour. For fire protection purposes he reports it as the vapour density ratio, which compares the vapour with an equal volume of air under the same conditions of temperature and pressure.[1] The ratio resembles the specific gravity of a liquid, except that air instead of water is the reference.[1] Drysdale uses the term gas specific gravity for the same ratio. He defines it with dry air at the same temperature and pressure as the reference, and notes that it can be derived from the ideal gas law.[2]
The Fire Protection Handbook (20th edition, 2008) gives the ratio as the molecular weight of the material divided by 29.[1] Drysdale explains that 29 is the effective molecular weight of dry air, which consists of about 21 percent oxygen and 79 percent nitrogen.[2] Vapour density ratios are reported at equal temperature and atmospheric pressure. Unequal or changing conditions appreciably change the density of any vapour.[1]
The term is linked to buoyancy, the upward force that the surrounding fluid exerts on a volume of gas. A gas with positive buoyancy is lighter than its surroundings and tends to rise, and a gas with negative buoyancy tends to sink.[2] Drysdale stresses that buoyancy depends on both the molecular weight and the temperature of the gas.[2] Vapour density in the narrow sense describes only the first of these two factors.[1]
Calculation from molar mass and temperature
Density is the ratio of mass to volume, expressed for example in kg/m³.[2] For gases that behave ideally, the density follows from the ideal gas law. Drysdale writes the density as the pressure multiplied by the molecular weight and divided by the gas constant and the absolute temperature:[10]
Because air follows the same law, the ratio of the two densities at equal pressure and temperature reduces to the ratio of the molecular weights. Pressure, temperature and the gas constant cancel out.[10] This is the handbook's vapour density ratio:[1][2]
Introduction to Fire Safety Engineering gives a short form of the ideal gas law for air and smoke at about 1 atmosphere. The density in kg/m³ is about 353 divided by the absolute temperature in kelvin. This gives about 1.2 kg/m³ at 20 °C and 0.75 kg/m³ at 200 °C.[11] The same section notes that the ideal gas law describes air at atmospheric pressure with an error of no more than a fraction of a percent.[11]
| Symbol | Description | Unit |
|---|---|---|
| , | density of a gas or vapour | kg/m³ |
| density of air | kg/m³ | |
| density of a vapour and air mixture | kg/m³ | |
| absolute pressure | Pa | |
| molecular weight (molar mass); in kg/mol in the density equation, in g/mol in the ratio with 29 | kg/mol, g/mol | |
| universal gas constant, 8.314 J/(mol·K) | J/(mol·K) | |
| absolute temperature | K | |
| vapour density ratio (air = 1) | – | |
| concentration of the vapour in the mixture | vol. % | |
| density of the pure vapour, here at 21 °C | kg/m³ |
The ideal gas law has limits for vapours. Drysdale notes that gases close to their condensation temperature, just above the boiling point of the liquid, deviate strongly from ideal behaviour. Such gases are more properly called vapours.[10] The ratio of molecular weights is therefore an approximation, and Slye warns that conditions different from equal temperature and atmospheric pressure change the density of any vapour appreciably.[1]
Temperature matters as much as molecular weight. The density of a gas falls as its temperature rises, which is why hot combustion products rise.[4] The reverse holds for cold vapours. Immediately after a spill of liquefied natural gas (LNG), the methane vapour is heavier than air because it is at a very low temperature, although methane has a molecular weight of only 16.[4]
Vapour and air mixtures
Pure vapours are seldom found in practice. They occur mainly where a liquid is stored above its boiling point. Above a liquid stored below its boiling point, the gas is a mixture of vapour and air.[1] For such liquids Slye calls the tabulated vapour density a possibly misleading value, because the mixture contains much less vapour.[1]
Slye illustrates this with ethyl acetate. At 21 °C its vapour pressure is about 16.2 kPa, so an equilibrium mixture in a closed vessel holds about 16 percent vapour and 84 percent air.[1] The theoretical vapour density of ethyl acetate is 3.0. The actual density ratio of the mixture is 0.16 × 3.0 + 0.84 × 1, or 1.32.[1] The mixture is still heavier than air, but much less so than the pure vapour.
DiNenno gives the same weighting in terms of density for gaseous extinguishing agents. It is the rule of Slye's example, written for densities instead of ratios. The density of an agent and air mixture is the vapour density of the agent times its volume fraction plus the density of air times the remaining fraction:[12]
DiNenno uses an air density of 1.202 kg/m³ and a vapour density of 6.283 kg/m³ for Halon 1301 at 21 °C. He notes that the mixture density is the driving force for leakage of agent from a protected room in still air.[12] The pure Halon 1301 vapour is thus about five times as dense as air, in line with Grant's description.[12][13]
Flammable mixtures are mostly air. Lemoff points out that most flammable gas and air mixtures are about 90 percent air. For this reason, whether the gas itself is lighter or heavier than air is less often a significant factor in gas explosions in buildings than one might expect.[14] Cholin adds that a leaking gas mixes with the air and changes its density. The density of the mixture depends on the gases present and on their proportions.[15]
Worked examples
Propane at 20 °C. Propane has a molecular weight of 44.[2] Its vapour density ratio is therefore 44/29, or about 1.52. Lemoff lists 1.50 for commercial propane at 15.5 °C.[1][3] With the ideal gas law at 101.3 kPa and 293.15 K, its density is 101,325 × 0.044 / (8.314 × 293.15), or about 1.83 kg/m³. Air under the same conditions has about 1.20 kg/m³.[10][11]
Propane and air at the lower flammable limit. The lower flammable limit of propane is 2.15 percent by volume.[3] Applying the mixture rule to this concentration gives a density ratio of 0.0215 × 1.50 + 0.9785 × 1, or about 1.01.[1][3] At the upper limit of 9.60 percent, the ratio is about 1.05. A propane mixture within its flammability limits is thus at most a few percent heavier than air. This explains Lemoff's remark that the density of the gas itself matters less in structures than its pure vapour density suggests.[14]
Cold methane after an LNG spill. Methane boils at −161.5 °C, or 111.65 K.[4] At that temperature, an ideal-gas estimate of its density relative to air at 20 °C is (16/29) × (293.15/111.65), or about 1.45.[10] This agrees with Lemoff, who states that LNG vapour near its normal boiling point is about 1.5 times as heavy as air at 21 °C.[16]
For pure methane in air at 20 °C, the same ideal-gas estimate places neutral buoyancy near −111 °C. Rivkin reports about −118 °C for an LNG vapour cloud in air at 16 °C.[10][17] These are approximate thresholds because the released gas is a mixture and vapours near their boiling points deviate from ideal behaviour.[10][17]
Halon 1301 in a flooded room. With DiNenno's values, a 5 percent Halon 1301 concentration gives a mixture density of 6.283 × 0.05 + 1.202 × 0.95, or about 1.46 kg/m³. This is about 21 percent more than the density of air.[12] Grant notes that Halon 1301 vapour is about 5 times heavier than air, so it typically escapes through openings low in a totally flooded volume.[13]
Vapour from a litre of acetone. Slye shows how vapour density gives the volume of vapour produced by a liquid. One litre of liquid yields 0.83 × specific gravity / vapour density cubic metres of vapour.[18] The factor 0.83 is the inverse of the density of air, 1.2 kg/m³.[11] For acetone, with a specific gravity of 0.792 and a vapour density of 2, one litre gives about 0.33 m³ of vapour.[18] With a lower flammable limit of 2.6 percent, about 37 volumes of air are needed per volume of vapour, or about 12.2 m³ of air per litre.[18]
Typical values
| Gas or vapour | Vapour density (air = 1) | Source |
|---|---|---|
| Hydrogen | 0.07 | [5] |
| Methane | 0.554 | [7] |
| Carbon monoxide | 0.967 | [7] |
| Ethane | 1.049 | [7] |
| Carbon dioxide | 1.528 | [7] |
| Propane | 1.55 (1.50 for commercial propane at 15.5 °C) | [7][3] |
| Acetone | 2.0 | [7] |
| Butane (commercial) | 2.01 | [3] |
| Chlorine | about 2.5 | [19] |
| Ethyl acetate | 3.0 | [1] |
| Toluene | 3.1 | [7] |
| Gasoline | 3.4 | [7] |
| Mineral spirits | 3.9 | [7] |
| Halon 1301 | about 5 | [13] |
The table shows that most flammable liquids produce vapours heavier than air. Slye states this directly for gasoline and almost all other flammable liquids.[20] Kingsbaker gives hexane solvent vapour as about three times heavier than air.[21]
Among the common gases, only a few are much lighter than air. Hydrogen, natural gas and methane rise and disperse quickly at normal temperatures.[17][5] Acetylene and ethylene are only slightly lighter than air, so acetylene does not readily dissipate.[22][23] Carbon monoxide is so close to air that it mixes readily with any air movement.[24]
Behaviour of released vapours
Heavy vapours settle. Slye explains that they settle on floors or in pits and depressions and may flow along the floor or ground for long distances. They can then be ignited at a remote point and flash back to the source.[20] The extra density of a heavy vapour can even make vapour from a spill travel upwind to unprotected ignition sources.[1] Drysdale describes how propane leaking slowly from a cylinder accumulates and spreads at ground level with little dilution, which is a serious hazard in a basement or a poorly ventilated boat.[2][4]
Releases of liquefied petroleum gas show this behaviour on a larger scale. Rivkin states that propane, with a vapour density of 1.5, sinks to the ground and forms a vapour cloud that follows surface contours over a large area.[5] Even outdoors such a cloud can travel downwind at flammable concentrations until it meets an ignition source.[25] At comparable temperatures, LP-gas vapour remains heavier than air because of its greater molecular weight; a hot plume or fast jet can behave differently.[26][2][27] Ignition of a large outdoor cloud under conditions that promote rapid flame speeds can lead to a vapour cloud explosion. Zalosh names propane, propylene, ethylene and various aromatic hydrocarbons among the vapours often involved.[28]
Light gases behave differently but are not harmless. Natural gas, with a vapour density below 1, rises at ambient conditions. Methane, at about 0.6, can pool under a ceiling in an enclosed space, where light fixtures and air-handling equipment may ignite it.[17] In an enclosed area methane can create an explosion hazard very rapidly.[4]
Cold releases form a third group. Lemoff explains that gas produced near the source of an evaporating liquefied gas can be heavier than ambient air because it is cold. Even normally lighter gases can therefore hug the ground near the source, accompanied by a visible water fog.[9] LNG vapour near its boiling point is about 1.5 times heavier than air and spreads along the ground with such a fog.[16] Rivkin adds that LNG vapour eventually becomes buoyant. At night it takes longer for the vapour to warm, so a flammable puff can travel farther.[5][26]
Carbon dioxide used for extinguishment is 1.5 times as dense as air at the same temperature. Its cold discharge is much denser still, which lets it replace air above burning surfaces.[29] When carbon dioxide is used for total flooding, the mixture of carbon dioxide and air is denser than the surrounding atmosphere.[29]
Use in ventilation, detection and ignition control
Ventilation design uses vapour density to place exhaust openings. Lataille states that exhaust openings near the floor are generally most effective where heavier-than-air vapours or mixtures are handled. Openings near the top of the room, hood or enclosure are most effective for lighter-than-air vapours.[6] Slye recommends removing heavy vapours at floor level, including pits, but notes that convection currents or diffusion may carry even heavy vapours upward. Ceiling ventilation may then also be desirable.[20] On boats, which cannot drain vapours through the bottom, ventilation is designed to remove heavier-than-air fuel vapours from the bottom of each compartment.[30]
A gas detection system also depends on vapour density. Cholin explains that in still air, lighter-than-air gases reach higher concentrations high in a space and heavier-than-air gases low in a space. Specific densities help predict where a leaking gas will go.[7] Sensors for methane, natural gas and other light gases are generally placed above the gas-containing equipment. Sensors for propane, butane and most vapours are placed low in the hazard area.[7] For carbon monoxide, whose vapour density is very close to that of air, Black notes that residential detectors can be mounted either on the ceiling or on the wall.[24]
The same reasoning sets the size of hazardous areas. Lemoff and Rivkin state that the vapour density of a stored gas partly determines the extent of the area in which ignition sources should be eliminated or controlled.[8] Fuel cell installations using propane need special ventilation because the gas collects in low-lying areas.[31] In building security design, Meacham and Galioto recommend high air intakes because most chemical and biological agents are heavier than air.[32]
Limits and common misconceptions
A vapour density is not a fixed behaviour. It describes the pure vapour at the same temperature and pressure as the air, while real releases are mixtures at other temperatures.[1] Cholin warns that a gas leaking from high pressure cools the air it flows into. The cooled mixture contracts, becomes denser and only slowly returns to ambient temperature.[7] Wind and air currents also move heavy gases, and the velocity of a pressurised jet release can overcome the effect of density altogether.[27]
A common misconception is that a vapour heavier than air will always stay low. Slye notes that convection currents of heated air or normal diffusion may carry heavy vapours upward.[20] The opposite error is to assume that a light gas cannot accumulate at low level, which cold LNG and hydrogen vapours disprove for some distance from the source.[9][16] A third error is to read the pure vapour density as the density of a flammable cloud, which is mostly air.[14]
Vapour density should also not be confused with vapour pressure. Vapour pressure sets the equilibrium vapour concentration above a liquid at a given temperature and total pressure, while vapour density helps predict where a release tends to go.[1] Published values can also disagree. Rivkin gives 0.07 for hydrogen and Biggins 0.1, while Table 14.8.1 of the handbook prints 0.7000.[5][31][7] Since 2/29 is about 0.07, the ideal-gas ratio supports Rivkin's value.[1]
See also
Notes
- ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 Slye (2008), p. 6-199.
- ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 Drysdale (2008), p. 2-5.
- ↑ 3.0 3.1 3.2 3.3 3.4 3.5 Lemoff (2008), p. 6-183.
- ↑ 4.0 4.1 4.2 4.3 4.4 4.5 Drysdale (2008), p. 2-6.
- ↑ 5.0 5.1 5.2 5.3 5.4 5.5 Rivkin (2008b), p. 21-59.
- ↑ 6.0 6.1 Lataille (2008), p. 8-7.
- ↑ 7.00 7.01 7.02 7.03 7.04 7.05 7.06 7.07 7.08 7.09 7.10 7.11 7.12 7.13 Cholin (2008a), p. 14-107.
- ↑ 8.0 8.1 Lemoff and Rivkin (2008), p. 7-41.
- ↑ 9.0 9.1 9.2 Lemoff (2008), p. 6-176.
- ↑ 10.0 10.1 10.2 10.3 10.4 10.5 10.6 Drysdale (2008), p. 2-9.
- ↑ 11.0 11.1 11.2 11.3 Van Rossum (2027), §3.2.
- ↑ 12.0 12.1 12.2 12.3 DiNenno (2002), p. 4-198.
- ↑ 13.0 13.1 13.2 Grant (2002), p. 4-152.
- ↑ 14.0 14.1 14.2 Lemoff (2008), p. 6-175.
- ↑ Cholin (2008a), p. 14-106.
- ↑ 16.0 16.1 16.2 Lemoff (2008), p. 6-182.
- ↑ 17.0 17.1 17.2 17.3 Rivkin (2008b), p. 21-58.
- ↑ 18.0 18.1 18.2 Slye (2008), p. 6-202.
- ↑ Lemoff (2008), p. 6-180.
- ↑ 20.0 20.1 20.2 20.3 Slye (2008), p. 6-207.
- ↑ Kingsbaker (2008), p. 9-135.
- ↑ Lemoff (2008), p. 6-178.
- ↑ Lemoff (2008), p. 6-181.
- ↑ 24.0 24.1 Black (2008), p. 14-115.
- ↑ Rivkin (2008b), p. 21-67.
- ↑ 26.0 26.1 Rivkin (2008b), p. 21-74.
- ↑ 27.0 27.1 Lemoff (2008), p. 6-184.
- ↑ Zalosh (2008), p. 2-104.
- ↑ 29.0 29.1 Wysocki (2008), p. 17-4.
- ↑ Eberly (2008), p. 21-152.
- ↑ 31.0 31.1 Biggins (2008), p. 8-110.
- ↑ Meacham and Galioto (2008), p. 1-129.
References
- Biggins, J. B. (2008). Stationary combustion engines and fuel cells. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-105–8-111). National Fire Protection Association.
- Black, A. (2008). Carbon monoxide detection in residential occupancies. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-113–14-117). National Fire Protection Association.
- Cholin, J. M. (2008a). Gas and vapor detection systems and monitors. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 14-99–14-112). National Fire Protection Association.
- DiNenno, P. J. (2002). Halon replacement clean agent total flooding systems. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-173–4-200). National Fire Protection Association; Society of Fire Protection Engineers.
- Drysdale, D. (2008). Physics and chemistry of fire. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-3–2-20). National Fire Protection Association.
- Eberly, R. (2008). Marine vessels. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-151–21-185). National Fire Protection Association.
- Grant, C. C. (2002). Halon design calculations. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), SFPE handbook of fire protection engineering (3rd ed., pp. 4-149–4-172). National Fire Protection Association; Society of Fire Protection Engineers.
- Kingsbaker, C. L. (2008). Oilseed solvent extraction plants. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 9-131–9-140). National Fire Protection Association.
- Lataille, J. I. (2008). Air-Moving equipment. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 8-3–8-15). National Fire Protection Association.
- Lemoff, T. C., & Rivkin, C. H. (2008). Storage of gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 7-35–7-42). National Fire Protection Association.
- Lemoff, T. C. (2008). Gases. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-165–6-186). National Fire Protection Association.
- Meacham, B. J., & Galioto, C. (2008). Protecting against extreme events. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 1-109–1-136). National Fire Protection Association.
- Rivkin, C. H. (2008b). Vehicle fueling using gaseous fuels. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 21-41–21-76). National Fire Protection Association.
- Slye, O. M., Jr. (2008). Flammable and combustible liquids. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 6-197–6-208). National Fire Protection Association.
- Van Rossum, E. (2027). Introduction to Fire Safety Engineering. Fire Safety Academy.
- Wysocki, T. J. (2008). Carbon dioxide and application systems. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 17-3–17-15). National Fire Protection Association.
- Zalosh, R. (2008). Explosions. In A. E. Cote, C. C. Grant, J. R. Hall Jr., & R. E. Solomon (Eds.), Fire protection handbook (20th ed., pp. 2-93–2-106). National Fire Protection Association.