Wildfire - Revision history

Mark: Revise against the FSE wiki writing guidelines: corrections after independent fact-check (revised by Claude Opus 5.5)

2026-11-02T18:33:42Z

Revise against the FSE wiki writing guidelines: corrections after independent fact-check (revised by Claude Opus 5.5)

Mark: Revise against the FSE wiki writing guidelines: verified and corrected citations, added sources, See also, links, style (revised by Claude Opus 5.5)

2026-11-02T18:11:02Z

Revise against the FSE wiki writing guidelines: verified and corrected citations, added sources, See also, links, style (revised by Claude Opus 5.5)

Show changes

Sanne: Add diagrams fse-wildfire-v1.svg, fse-wildfire-v2.svg, fse-wildfire-v3.svg (level-1 visual plan)

2026-11-02T07:24:48Z

Add diagrams fse-wildfire-v1.svg, fse-wildfire-v2.svg, fse-wildfire-v3.svg (level-1 visual plan)

← Older revision		Revision as of 08:24, 2 November 2026
Line 10:		Line 10:

	Terrain changes flame contact and convective heating. A slope can tilt flames towards unburned fuel and increase preheating there, while wind can have a similar or reinforcing effect. The direction of spread must therefore be evaluated with the terrain, not only with the fuel name.<ref name="Quintiere-2-255" /><ref name="Simcox-3-208">Simcox, Wilkes, and Jones (2002), p. 3-208.</ref>		Terrain changes flame contact and convective heating. A slope can tilt flames towards unburned fuel and increase preheating there, while wind can have a similar or reinforcing effect. The direction of spread must therefore be evaluated with the terrain, not only with the fuel name.<ref name="Quintiere-2-255" /><ref name="Simcox-3-208">Simcox, Wilkes, and Jones (2002), p. 3-208.</ref>
			[[File:fse-wildfire-v1.svg\|thumb\|upright=1.5\|alt=Wind and slope tilt flames towards uphill vegetation while a fuel gap interrupts one path.\|Wildfire spread depends on fuel, terrain and wind. Based on Quintiere (2002), pp. 2-255–2-256 and Simcox, Wilkes, and Jones (2002), p. 3-208.]]

	Humidity and weather alter the environment in which fuels dry and burn. Quintiere lists fuel configuration, terrain, wind and humidity as the main influences in the source treatment. Those variables must be represented for the particular location and time.<ref name="Quintiere-2-255" />		Humidity and weather alter the environment in which fuels dry and burn. Quintiere lists fuel configuration, terrain, wind and humidity as the main influences in the source treatment. Those variables must be represented for the particular location and time.<ref name="Quintiere-2-255" />
Line 34:		Line 35:

	Large embers can travel great distances in the cited account. Their effect depends on where they land, their remaining energy and the condition of the receiving fuel. A firebreak alone therefore cannot demonstrate protection from every ignition path.<ref name="Quintiere-2-255" />		Large embers can travel great distances in the cited account. Their effect depends on where they land, their remaining energy and the condition of the receiving fuel. A firebreak alone therefore cannot demonstrate protection from every ignition path.<ref name="Quintiere-2-255" />
			[[File:fse-wildfire-v2.svg\|thumb\|upright=1.5\|alt=Wind carries burning brands over a fuel break to ignite a separate spot fire.\|Firebrands create discontinuous spread beyond the main fire front. Based on Quintiere (2002), pp. 2-255–2-256 and Hamins et al. (2005), p. 29.]]

	NIST's workstation analysis describes burning brands as a mechanism observed in warehouse and wildland fires involving cellulosic material. It also reports that brands were not the mechanism in that particular video record. This distinction illustrates the need for evidence of the mechanism in the actual incident.<ref name="Hamins-29" />		NIST's workstation analysis describes burning brands as a mechanism observed in warehouse and wildland fires involving cellulosic material. It also reports that brands were not the mechanism in that particular video record. This distinction illustrates the need for evidence of the mechanism in the actual incident.<ref name="Hamins-29" />
Line 46:		Line 48:

	Structures can be exposed to radiation, flames and firebrands. The relevant assessment should consider which mechanism delivers enough energy to ignite the building or its contents. Treating every structure loss as direct contact with the main flame front would miss the other pathways.<ref name="Quintiere-2-255" /><ref name="Hamins-29" />		Structures can be exposed to radiation, flames and firebrands. The relevant assessment should consider which mechanism delivers enough energy to ignite the building or its contents. Treating every structure loss as direct contact with the main flame front would miss the other pathways.<ref name="Quintiere-2-255" /><ref name="Hamins-29" />
			[[File:fse-wildfire-v3.svg\|thumb\|upright=1.5\|alt=Vegetation fire exposes a building by direct flames, radiant heat and firebrands.\|Buildings at the wildland-urban interface face several ignition pathways. Based on Quintiere (2002), pp. 2-255–2-256 and Hamins et al. (2005), p. 29.]]

	The condition of vegetation and other fuels around a structure affects exposure. Gaps can reduce direct flame spread, but the required break depends on fire intensity and heat-transfer characteristics. Firebrands can still create ignition beyond that gap.<ref name="Quintiere-2-255" />		The condition of vegetation and other fuels around a structure affects exposure. Gaps can reduce direct flame spread, but the required break depends on fire intensity and heat-transfer characteristics. Firebrands can still create ignition beyond that gap.<ref name="Quintiere-2-255" />

Jan: New FSE wiki article: Wildfire (written by Kimi Code CLI)

2026-11-02T04:18:52Z

New FSE wiki article: Wildfire (written by Kimi Code CLI)

New page

A '''Wildfire''' is a fire spreading through vegetation or other natural fuel, with behaviour shaped by fuel type and arrangement, terrain, wind and humidity. It can involve surface litter, brush and, in severe cases, tree crowns. Wildfires present different assessment problems from a single burning item in a building because their fuels and environmental conditions vary across the terrain.<ref name="Quintiere-2-255">Quintiere (2002), pp. 2-255–2-256.</ref>

Wildfire spread combines radiation, convection and the movement of burning material. Wind can carry large embers far from the main fire and start spot fires elsewhere. The wildland-urban interface introduces buildings and infrastructure into that environment, so exposure and ignition of structures must also be assessed.<ref name="Quintiere-2-255" /><ref name="FDS-iii">McGrattan et al. (2026), p. iii.</ref>

The supplied documents provide a basic account rather than a complete wildfire design method. This article therefore stays shorter than other Basic entries and does not invent fuel models, suppression tactics or regulatory requirements. More detailed wildfire behaviour and planning evidence is needed for project-specific assessment.<ref name="Quintiere-2-255" /><ref name="Hall-5-65">Hall and Ahrens (2002), pp. 5-65–5-67.</ref>

== Fuel, terrain and fire environment ==

Fuel type and configuration influence how a wildfire starts and spreads. Fine surface material, brush and tree crowns offer different burning arrangements and heat-transfer paths. In severe fires, both the porous brush at the forest floor and the crowns can participate.<ref name="Quintiere-2-255" />

Terrain changes flame contact and convective heating. A slope can tilt flames towards unburned fuel and increase preheating there, while wind can have a similar or reinforcing effect. The direction of spread must therefore be evaluated with the terrain, not only with the fuel name.<ref name="Quintiere-2-255" /><ref name="Simcox-3-208">Simcox, Wilkes, and Jones (2002), p. 3-208.</ref>

Humidity and weather alter the environment in which fuels dry and burn. Quintiere lists fuel configuration, terrain, wind and humidity as the main influences in the source treatment. Those variables must be represented for the particular location and time.<ref name="Quintiere-2-255" />

The fire environment can change across short distances. Fuel breaks, vegetation changes and terrain alter the available heat-transfer paths. A break that interrupts one fire may be insufficient for another, because its required size depends on fire intensity and heat transfer.<ref name="Quintiere-2-255" />

The source documents do not provide a universal fuel-moisture or fuel-load value for these assessments. They instead support an explanation of the physical inputs that must be obtained from an appropriate wildland-fire method.<ref name="Quintiere-2-255" /><ref name="Hall-5-65" />

== Flame spread and heat transfer ==

[[Flame spread]] is the movement of flame through a fuel arrangement. Wildfire can spread when heat from the flame and hot gases ignites vegetation ahead of the burning front. Wind and slope influence that process through convective heating and flame orientation.<ref name="Quintiere-2-255" />

Radiative heating can preheat fuel before direct flame contact. [[Flame radiation]] therefore contributes to ignition and to the conditions experienced by people and structures at a distance. The required assessment should consider both the flame front and the heat reaching exposed targets.<ref name="Quintiere-2-255" /><ref name="Hamins-29">Hamins et al. (2005), p. 29.</ref>

Fire spread can also be intermittent. A spot fire may start away from the main front and develop separately before later interacting with it. Treating the entire event as one smooth line of flame would miss that discontinuous behaviour.<ref name="Quintiere-2-255" />

[[Fire spread]] between fuels is not always a simple contiguous path. NIST's workstation experiments distinguish radiation from the hot layer from flame spread by a continuously burning item. That evidence concerns a compartment, but it illustrates why ignition mechanism must be established rather than assumed.<ref name="Hamins-29" />

The source describes practical models for forest-fire behaviour but does not reproduce their equations or input data. Those methods require a suitable fuel, weather and terrain description and should not be replaced by an invented Basic-level correlation.<ref name="Quintiere-2-255" />

== Firebrands and spot fires ==

[[Firebrands]] are burning particles carried away from the main fire by convection and wind. They can land on combustible material and start spot fires at distant locations. This transport mechanism can bypass the area that would otherwise interrupt direct flame spread.<ref name="Quintiere-2-255" /><ref name="Hamins-29" />

Large embers can travel great distances in the cited account. Their effect depends on where they land, their remaining energy and the condition of the receiving fuel. A firebreak alone therefore cannot demonstrate protection from every ignition path.<ref name="Quintiere-2-255" />

NIST's workstation analysis describes burning brands as a mechanism observed in warehouse and wildland fires involving cellulosic material. It also reports that brands were not the mechanism in that particular video record. This distinction illustrates the need for evidence of the mechanism in the actual incident.<ref name="Hamins-29" />

Firebrands can make the hazard geographically discontinuous. Assessment must consider both the area near the main fire and potential landing zones for transported burning material. The exposure of those zones depends on their fuel and the heat delivered by the brand.<ref name="Quintiere-2-255" /><ref name="Hamins-29" />

The supplied sources do not give a universal travel distance or ignition probability for firebrands. Those outcomes depend on particle properties, fire behaviour, wind and receiving fuel, so no numerical distance is stated here.<ref name="Quintiere-2-255" />

== Wildland-urban interface ==

The [[Wildland-urban interface]] is where vegetation fires interact with buildings and other developed assets. FDS research topics explicitly include wildland and wildland-urban interface fires, with attention to heat and mass transfer and prediction of fire growth. Those research areas show that the interface introduces coupled fuel and structure problems.<ref name="FDS-iii" />

Structures can be exposed to radiation, flames and firebrands. The relevant assessment should consider which mechanism delivers enough energy to ignite the building or its contents. Treating every structure loss as direct contact with the main flame front would miss the other pathways.<ref name="Quintiere-2-255" /><ref name="Hamins-29" />

The condition of vegetation and other fuels around a structure affects exposure. Gaps can reduce direct flame spread, but the required break depends on fire intensity and heat-transfer characteristics. Firebrands can still create ignition beyond that gap.<ref name="Quintiere-2-255" />

Evidence from compartment fires can help explain radiation and ignition but cannot replace wildland-specific inputs. A room's hot layer and a terrain fire differ in fuel geometry, weather and scale. Models must therefore be chosen for the actual environment.<ref name="Hamins-29" /><ref name="FDS-iii" />

The supplied sources do not provide a complete defensible-space or construction standard for the interface. No universal clearance, façade treatment or building-protection requirement is therefore stated. Such provisions must come from the applicable wildfire and building guidance.<ref name="Hall-5-65" /><ref name="Quintiere-2-255" />

== Suppression and exposure protection ==

Suppression can aim to control spread, protect exposed material or extinguish burning fuel. NUREG-1805 describes foam for wildland use involving ordinary combustible materials, with compressed-air or foam equipment used through hose lines. Those examples concern the cited Class A foam applications rather than every wildfire situation.<ref name="NUREG-B60">U.S. Nuclear Regulatory Commission (2005), p. B-60.</ref>

The cited Class A foams are generally mixed at 0.1 to 1.0 percent in water for those applications. Foam can help exclude air and cool material, but heat, airflow and mechanical forces can disrupt the blanket. The required formulation and application depend on the fuel and fire conditions.<ref name="NUREG-B60" /><ref name="NUREG-B58">U.S. Nuclear Regulatory Commission (2005), pp. B-58–B-59.</ref>

Exposure protection must consider where heat and firebrands travel. Water or another suitable agent may protect unburned material even where the main fire is not extinguished. Its delivery and persistence must be assessed under wind and fire conditions.<ref name="NUREG-B58" /><ref name="NUREG-B60" />

Suppression decisions also affect responders and other people. Smoke, heat, changing wind and difficult terrain can alter access and exposure. The supplied sources do not provide a complete operational wildfire suppression protocol, so no universal attack sequence is given.<ref name="Quintiere-2-255" /><ref name="Hall-5-65" />

== Evidence and assessment limits ==

Wildfire assessment requires appropriate fuel, weather, terrain and exposure data. Incident observations, laboratory tests and field data can contribute different evidence, but their representativeness must be checked. A model chosen for a building or another terrain cannot be assumed to apply directly.<ref name="Hall-5-65" /><ref name="FDS-iii" />

FDS research includes sub-models for wildland and interface fires, which is a different modelling domain from its compartment applications. A computational result depends on those sub-models and their inputs, not only on the software name. Validation must address the actual fire environment.<ref name="FDS-iii" /><ref name="Notarianni-5-43">Notarianni (2002), pp. 5-43–5-44.</ref>

Firebrands and spot fires add uncertainty to the location and timing of ignition. A scenario should therefore include possible landing zones and alternative spread paths. A single continuous fire-front map may not capture those outcomes.<ref name="Quintiere-2-255" /><ref name="Hamins-29" />

The available documents do not supply a full wildfire prevention, suppression or WUI planning method. Additional wildland-fire behaviour, firebrand exposure, responder safety and local regulatory sources would be needed for a more detailed treatment. Those gaps should remain visible in any subsequent engineering assessment.<ref name="Hall-5-65" /><ref name="Quintiere-2-255" />

== See also ==

* [[Firebrands]]
* [[Flame spread]]
* [[Wildland-urban interface]]

== Notes ==

<references />

== References ==

* Hall, J. R., Jr., & Ahrens, M. J. (2002). Data for engineering analysis. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Hamins, A., Maranghides, A., McGrattan, K. B., Ohlemiller, T. J., & Anleitner, R. L. (2005). ''Experiments and modeling of multiple workstations burning in a compartment'' (NIST NCSTAR 1-5E). National Institute of Standards and Technology.
* McGrattan, K., Hostikka, S., Floyd, J., McDermott, R., Vanella, M., Mueller, E., & Paul, C. (2026). ''Fire Dynamics Simulator technical reference guide: Volume 1: Mathematical model'' (6th ed.). National Institute of Standards and Technology.
* Notarianni, K. A. (2002). Uncertainty. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Quintiere, J. G. (2002). Surface flame spread. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Simcox, S., Wilkes, N. S., & Jones, I. P. (2002). Computer simulation of smoke movement in buildings. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* U.S. Nuclear Regulatory Commission. (2005). ''Fire dynamics tools: Quantitative fire hazard analysis methods for the U.S. nuclear regulatory commission fire protection inspection program'' (NUREG-1805). Author.

[[Category:Special Hazards & Building Types]]