Flame spread - Revision history

Jan: Remove links to pages that do not exist; retain displayed text (wiki-wide link audit).

2026-11-02T21:32:51Z

Remove links to pages that do not exist; retain displayed text (wiki-wide link audit).

← Older revision		Revision as of 22:32, 2 November 2026
Line 74:		Line 74:
	== Testing and measurement ==		== Testing and measurement ==

	The [[Single Burning Item test]] is described in the 2002 handbook as a European regulatory heat-release-rate test for building products. Two panels form a corner without a ceiling. This geometry differs from a complete room, so its result does not directly represent every installed exposure.<ref name="Babrauskas-3-32" />		The Single Burning Item test is described in the 2002 handbook as a European regulatory heat-release-rate test for building products. Two panels form a corner without a ceiling. This geometry differs from a complete room, so its result does not directly represent every installed exposure.<ref name="Babrauskas-3-32" />

	Quintiere discusses cone-calorimeter and lateral ignition and flame-spread tests as sources of material data. These methods helped replace less meaningful flammability indices with measurements linked to ignition and spread models. They do not remove all uncertainty in heat-transfer and material-property inputs.<ref name="Quintiere-2-247" />		Quintiere discusses cone-calorimeter and lateral ignition and flame-spread tests as sources of material data. These methods helped replace less meaningful flammability indices with measurements linked to ignition and spread models. They do not remove all uncertainty in heat-transfer and material-property inputs.<ref name="Quintiere-2-247" />

Peter: Improve FSE wiki article: Flame spread; source, clarity and calculation review (GPT-6)

2026-11-02T17:31:59Z

Improve FSE wiki article: Flame spread; source, clarity and calculation review (GPT-6)

Show changes

Sanne: Add diagrams fse-flame-spread-v1.svg, fse-flame-spread-v2.svg, fse-flame-spread-v3.svg (level-1 visual plan)

2026-11-02T07:16:12Z

Add diagrams fse-flame-spread-v1.svg, fse-flame-spread-v2.svg, fse-flame-spread-v3.svg (level-1 visual plan)

← Older revision		Revision as of 08:16, 2 November 2026
Line 8:		Line 8:

	The visible flame occupies the gas phase, while the condensed fuel remains beneath or beside it. Heat transferred from the flame evaporates liquid or decomposes solid ahead of the current burning area. The new vapour mixes with air and allows the flame to advance.<ref name="Quintiere-2-246" />		The visible flame occupies the gas phase, while the condensed fuel remains beneath or beside it. Heat transferred from the flame evaporates liquid or decomposes solid ahead of the current burning area. The new vapour mixes with air and allows the flame to advance.<ref name="Quintiere-2-246" />
			[[File:fse-flame-spread-v1.svg\|thumb\|upright=1.5\|alt=Gas-phase flame above a solid with a separate advancing pyrolysis front.\|Surface flame spread involves two advancing fronts. Based on Quintiere (2002), p. 2-246.]]

	The evaporation or pyrolysis front is harder to observe than the flame, but it marks the region being converted into gaseous fuel. Its position and movement connect the visible flame with fuel consumption. A flame can appear substantial while the underlying front moves comparatively slowly.<ref name="Quintiere-2-246" />		The evaporation or pyrolysis front is harder to observe than the flame, but it marks the region being converted into gaseous fuel. Its position and movement connect the visible flame with fuel consumption. A flame can appear substantial while the underlying front moves comparatively slowly.<ref name="Quintiere-2-246" />
Line 28:		Line 29:

	[[Upward flame spread]] benefits from buoyant hot gases and flame contact preheating fuel above the front. This can produce a large heated region and rapid acceleration on vertical surfaces. Van Rossum identifies this mechanism as an important reason for faster upward spread.<ref name="VR-4.3">Van Rossum (2027), §4.3.</ref><ref name="Quintiere-2-247" />		[[Upward flame spread]] benefits from buoyant hot gases and flame contact preheating fuel above the front. This can produce a large heated region and rapid acceleration on vertical surfaces. Van Rossum identifies this mechanism as an important reason for faster upward spread.<ref name="VR-4.3">Van Rossum (2027), §4.3.</ref><ref name="Quintiere-2-247" />
			[[File:fse-flame-spread-v2.svg\|thumb\|upright=1.5\|alt=Upward flame preheating fuel above and a front advancing against airflow.\|Flow direction changes flame-spread heat transfer. Based on Van Rossum (2027), §4.3 and Quintiere (2002), p. 2-247.]]

	[[Opposed-flow flame spread]] occurs when the front advances against the surrounding gas flow. Forward heat must reach fuel despite that opposing transport. Quintiere distinguishes this from wind-aided spread, where the surrounding flow supports movement in the same direction.<ref name="Quintiere-2-247" />		[[Opposed-flow flame spread]] occurs when the front advances against the surrounding gas flow. Forward heat must reach fuel despite that opposing transport. Quintiere distinguishes this from wind-aided spread, where the surrounding flow supports movement in the same direction.<ref name="Quintiere-2-247" />
Line 52:		Line 54:

	The handbook's order-of-magnitude table lists smouldering at 0.001 to 0.01 cm/s, lateral or downward spread on thick solids around 0.1 cm/s, and upward spread on thick solids from 1 to 100 cm/s. Premixed laminar deflagration is listed from 10 to 100 cm/s. These ranges show different mechanisms and scales, not values for direct substitution into another scenario.<ref name="Quintiere-2-247" />		The handbook's order-of-magnitude table lists smouldering at 0.001 to 0.01 cm/s, lateral or downward spread on thick solids around 0.1 cm/s, and upward spread on thick solids from 1 to 100 cm/s. Premixed laminar deflagration is listed from 10 to 100 cm/s. These ranges show different mechanisms and scales, not values for direct substitution into another scenario.<ref name="Quintiere-2-247" />
			[[File:fse-flame-spread-v3.svg\|thumb\|upright=1.5\|alt=Log-scale ranges for smouldering, lateral spread, upward spread and premixed flame.\|Order-of-magnitude flame-spread rates from the SFPE Handbook. Based on Quintiere (2002), p. 2-247.]]

	[[Fire spread]] beyond the first object adds further pathways such as radiation, direct flame contact and burning debris. Surface flame spread is one mechanism within this wider process. A room or building fire should not be modelled as one continuous sheet of fuel unless that geometry actually applies.<ref name="IFEG-1.6-7">Australian Building Codes Board et al. (2005), p. 1.6-7.</ref>		[[Fire spread]] beyond the first object adds further pathways such as radiation, direct flame contact and burning debris. Surface flame spread is one mechanism within this wider process. A room or building fire should not be modelled as one continuous sheet of fuel unless that geometry actually applies.<ref name="IFEG-1.6-7">Australian Building Codes Board et al. (2005), p. 1.6-7.</ref>

Jan: New FSE wiki article: Flame spread (written by Kimi Code CLI)

2026-11-01T22:50:59Z

New FSE wiki article: Flame spread (written by Kimi Code CLI)

New page

'''Flame spread''' is the movement of a flame across or adjacent to a condensed fuel whose evaporation or pyrolysis supplies the flame with gaseous fuel. It involves two advancing regions: the visible gas-phase flame and the evaporation or decomposition front in the solid or liquid. The rate of the condensed-phase front defines surface flame-spread velocity.<ref name="Quintiere-2-246">Quintiere (2002), p. 2-246.</ref>

The process differs from flame propagation through a premixed gas. In surface flame spread, fuel and oxygen are not already distributed uniformly throughout the gas. Heat from the advancing flame must first produce new vapour ahead of the reaction region.<ref name="Quintiere-2-246" />

Flame spread influences how rapidly a small ignition develops into a larger fire. It can accelerate as more fuel and stronger heat feedback become involved, or stop when forward heating, fuel continuity or combustion conditions become inadequate.<ref name="Quintiere-2-246" /><ref name="Drysdale-1-97">Drysdale (2002), p. 1-97.</ref>

== Flame and decomposition fronts ==

The visible flame occupies the gas phase, while the condensed fuel remains beneath or beside it. Heat transferred from the flame evaporates liquid or decomposes solid ahead of the current burning area. The new vapour mixes with air and allows the flame to advance.<ref name="Quintiere-2-246" />

The evaporation or pyrolysis front is harder to observe than the flame, but it marks the region being converted into gaseous fuel. Its position and movement connect the visible flame with fuel consumption. A flame can appear substantial while the underlying front moves comparatively slowly.<ref name="Quintiere-2-246" />

This mechanism can be viewed as successive [[Ignition]] of new material. Each newly heated region must reach a condition supporting piloted reaction and continued vapour supply. Flame spread therefore depends on the target's initial temperature and ignition response as well as on the existing flame.<ref name="Kanury-2-229">Kanury (2002), p. 2-229.</ref>

A premixed gas flame follows a different mechanism. Fuel and oxidiser are already present in the gas, so propagation can be much faster and does not require an advancing solid-decomposition front. The two processes should not share an unqualified spread-rate value.<ref name="Quintiere-2-246" />

== Heat transfer ahead of the flame ==

Forward heat transfer raises fuel from its initial temperature towards its ignition condition. Conduction through gas and solid, convection from hot gases and radiation from the flame can all contribute. Their relative importance depends on flow, orientation, scale and material properties.<ref name="Quintiere-2-247">Quintiere (2002), p. 2-247.</ref>

Quintiere's conceptual energy balance compares heat delivered ahead of the front with the energy needed to prepare new fuel. Lower initial temperature requires more heating, while preheating by the wider fire reduces the additional energy needed. Spread can therefore accelerate as the surroundings become hotter.<ref name="Quintiere-2-247" />

Heat losses can prevent the front from sustaining itself. Energy entering a thick solid can drain into its interior, and convection can cool the reaction region. Stronger opposed flow may enhance some heat-transfer paths while reducing the time available for chemical reaction, so its effect is not universally positive or negative.<ref name="Quintiere-2-248">Quintiere (2002), pp. 2-248–2-250.</ref>

Flame temperature and heat flux are also coupled with oxygen and chemistry. Reduced oxygen can lower reaction and heat release, while excessive flow can quench the reaction region. Material data alone cannot predict spread without these fire conditions.<ref name="Quintiere-2-248" />

== Direction and airflow ==

[[Upward flame spread]] benefits from buoyant hot gases and flame contact preheating fuel above the front. This can produce a large heated region and rapid acceleration on vertical surfaces. Van Rossum identifies this mechanism as an important reason for faster upward spread.<ref name="VR-4.3">Van Rossum (2027), §4.3.</ref><ref name="Quintiere-2-247" />

[[Opposed-flow flame spread]] occurs when the front advances against the surrounding gas flow. Forward heat must reach fuel despite that opposing transport. Quintiere distinguishes this from wind-aided spread, where the surrounding flow supports movement in the same direction.<ref name="Quintiere-2-247" />

Lateral and downward configurations have different heat-transfer paths and generally different rates from upward spread. The direction of gravity changes buoyancy, flame shape and which fuel is preheated. Material orientation must therefore accompany any reported rate.<ref name="Quintiere-2-247" />

External wind and fire-induced natural convection can both create the relevant flow. A value measured in still air cannot be transferred automatically to a ventilated shaft, open facade or compartment with strong fire-driven circulation.<ref name="Quintiere-2-247" /><ref name="IFEG-2.6-12">Australian Building Codes Board et al. (2005), p. 2.6-12.</ref>

== Material thickness and thermal response ==

Thermally thin materials have relatively little temperature variation through their thickness in the simplified model. Paper, garments and draperies can sometimes approach this behaviour. Thermally thick materials retain important internal gradients, and heat conducted into them is unavailable at the surface.<ref name="Quintiere-2-248" />

Geometric thickness alone does not define the thermal class. Conductivity, density, specific heat, exposure time and backing conditions all influence the response. Quintiere gives approximate material-specific examples, but these should not be converted into universal thickness thresholds.<ref name="Quintiere-2-249">Quintiere (2002), p. 2-249.</ref>

Low density can favour rapid response because less energy is required to prepare a given volume for ignition. Substrates can add further heat storage or loss. A thin combustible finish on a massive backing can consequently behave differently from the same finish without that backing.<ref name="Quintiere-2-247" /><ref name="Quintiere-2-249" />

Moisture, melting and char formation change the response during heating. They alter heat consumption, surface integrity and volatile release. Treating the material as homogeneous and unchanged is a modelling simplification whose limits must be stated.<ref name="Kanury-2-232">Kanury (2002), p. 2-232.</ref><ref name="Beyler-Hirschler-1-112">Beyler and Hirschler (2002), p. 1-112.</ref>

== Spread rate and fire growth ==

Quintiere illustrates growth with an upholstered-chair ignition region 6 cm in diameter and an unenhanced spread rate of about 1 mm/s. After one minute in the example, the pyrolysing region reaches 18 cm in diameter as the front advances 6 cm. The larger fuel area can then strengthen heat feedback.<ref name="Quintiere-2-246" />

The example demonstrates area growth rather than a universal chair-fire rate. Spread rate can change as heat release increases, and fuel burnout can limit later development. Early spread and long-term fire growth therefore require a time-dependent description.<ref name="Quintiere-2-246" />

The handbook's order-of-magnitude table lists smouldering at 0.001 to 0.01 cm/s, lateral or downward spread on thick solids around 0.1 cm/s, and upward spread on thick solids from 1 to 100 cm/s. Premixed laminar deflagration is listed from 10 to 100 cm/s. These ranges show different mechanisms and scales, not values for direct substitution into another scenario.<ref name="Quintiere-2-247" />

[[Fire spread]] beyond the first object adds further pathways such as radiation, direct flame contact and burning debris. Surface flame spread is one mechanism within this wider process. A room or building fire should not be modelled as one continuous sheet of fuel unless that geometry actually applies.<ref name="IFEG-1.6-7">Australian Building Codes Board et al. (2005), p. 1.6-7.</ref>

== Materials and fire performance ==

[[Combustibility]] describes whether and how a material can burn under relevant conditions, but it does not specify a flame-spread rate by itself. Ignition response, heat capacity, decomposition and geometry all affect movement across the material. Two combustible products can therefore spread fire very differently.<ref name="Quintiere-2-247" /><ref name="Beyler-Hirschler-1-112" />

[[Reaction to fire]] concerns how a material or product contributes to fire behaviour, including ignition and spread under specified tests. It is a broader performance description than simple presence of fuel. Test exposure and product arrangement remain necessary when interpreting any classification.<ref name="Quintiere-2-247" /><ref name="IFEG-3.3-3">Australian Building Codes Board et al. (2005), p. 3.3-3.</ref>

Surface orientation and installation affect measured performance. A product tested horizontally may not behave identically on a wall or ceiling, and joints or substrates can alter heat transfer. The tested specimen and the installed product must be compared explicitly.<ref name="Quintiere-2-247" />

A material can resist initial ignition yet still spread flame under a larger exposure. The threshold crossed in one test does not prove performance in every fire. Scenario severity and duration remain part of the assessment.<ref name="Kanury-2-231">Kanury (2002), pp. 2-231–2-232.</ref>

== Testing and measurement ==

The [[Single Burning Item test]] is one standardised fire-test arrangement used to evaluate product response. Its result belongs to that method and should not be treated as a direct measurement of every real installation. Flame spread in an actual room can involve additional radiation, ventilation and fuel geometry.<ref name="IFEG-2.6-12" /><ref name="Quintiere-2-247" />

Quintiere discusses cone-calorimeter and lateral ignition and flame-spread tests as sources of material data. These methods helped replace less meaningful flammability indices with measurements linked to ignition and spread models. They do not remove all uncertainty in heat-transfer and material-property inputs.<ref name="Quintiere-2-247" />

A spread-rate measurement needs an identifiable front, direction and exposure condition. Visible flame length alone does not establish how quickly the pyrolysis region moves. Measurement definitions can therefore change the reported result.<ref name="Quintiere-2-246" />

Tests at reduced scale can underrepresent radiation and room feedback. As the fire grows, upper-layer radiation and heated boundaries can preheat new regions beyond the local test arrangement. Applying small-scale rates to a developed enclosure fire requires an appropriate model.<ref name="Tien-1-73">Tien, Lee, and Stretton (2002), p. 1-73.</ref><ref name="IFEG-2.4-4">Australian Building Codes Board et al. (2005), p. 2.4-4.</ref>

== Fire growth and limits ==

Flame spread competes with burning time. Rapid spread can involve new fuel before the original region burns out, favouring acceleration. Slow spread can allow fuel depletion and heat losses to overtake growth. The process is consequently unstable and can change direction in rate over time.<ref name="Quintiere-2-246" />

Fire-induced preheating changes the conditions at the front. Initial fuel temperature rises, and the additional energy needed from the advancing flame decreases. This feedback can turn a slow initial spread into faster growth without any change in material chemistry.<ref name="Quintiere-2-247" />

Spread can also stop. Discontinuous fuel, excessive heat loss, oxygen limitation and reaction quenching can all interrupt the mechanism. A flame at one location does not prove that propagation across the whole material is sustainable.<ref name="Quintiere-2-248" /><ref name="Drysdale-1-97" />

Prediction remains limited by material data and fire-condition information. Quintiere notes that forward heat transfer is difficult to compute from first principles and that configuration effects are not fully established. Simple formulas illustrate mechanisms but should not hide those limitations.<ref name="Quintiere-2-247" />

A defensible assessment therefore records the material, thickness, backing, orientation, airflow, exposure and selected time. It distinguishes local surface spread from wider fire spread and uses test data only where the model and configuration support them.<ref name="Quintiere-2-247" /><ref name="IFEG-2.6-12" />

Comparing rates requires particular care when the front is not steady. An average over one interval can hide acceleration caused by growing heat feedback, while an instantaneous value can depend on local flame fluctuations. The measurement interval and the development stage should therefore accompany the result.<ref name="Quintiere-2-246" />

Initial fuel temperature provides another source of variation. Warmer fuel needs less additional energy before reaching its ignition condition, so the same flame can produce faster spread after prolonged preheating. This is one reason a rate measured at ambient conditions may underestimate spread in a heated enclosure.<ref name="Quintiere-2-247" />

Vertical arrangements also change the area being prepared. A flame leaning towards a wall can expose fuel above the current front, while a ceiling can hold hot gases near combustible surfaces. These effects are geometric and cannot be captured by a material-only flammability label.<ref name="VR-4.3" /><ref name="Quintiere-2-247" />

In opposed flow, reaction time and transport time compete. Quintiere explains that excessive flow can prevent reactions from completing and reduce spread or cause extinction. A simple statement that more airflow always increases spread would neglect this chemical and thermal balance.<ref name="Quintiere-2-248" />

Test data should consequently be used with a model that represents the intended configuration. Cone-calorimeter and lateral-spread results supply valuable properties, but room feedback, external wind and installed geometry can change their application. Extrapolation needs to be justified rather than assumed.<ref name="Quintiere-2-247" /><ref name="Tien-1-73" />

Where classifications are compared, the underlying method must remain attached. A reaction-to-fire result from one apparatus does not provide a universal ranking for every exposure and orientation. Different regulatory systems can also use the result differently, so this article does not assign a jurisdiction-specific class.<ref name="IFEG-2.6-12" /><ref name="IFEG-3.3-3" />

The final record should show how the front was identified and which heat-transfer mechanisms were represented. It should also state whether fuel burnout, changing temperature and ventilation were included. These details make the limits of a spread prediction visible to later reviewers.<ref name="Quintiere-2-246" /><ref name="Quintiere-2-247" />

Flame-spread analysis should also preserve the difference between flame size and front velocity. A longer flame can expose more fuel and alter later acceleration, but it does not directly measure how fast the decomposition boundary moves. Both observations are needed to understand the developing fire.<ref name="Quintiere-2-246" />

Changes at the burning surface can create further feedback. Char, melting and loss of material can change heat absorption and the area available for vapour production. A constant-property model may therefore be suitable only for a limited stage of spread.<ref name="Kanury-2-232" /><ref name="Beyler-Hirschler-1-112" />

Where a prediction affects design, the most uncertain inputs can be varied explicitly. Initial temperature, heat flux, airflow and backing condition are useful candidates because they alter the energy available to prepare new fuel. The resulting range of spread behaviour is more informative than an unsupported single rate. The same range also makes clear where additional measurements would be most useful in the intended installation and exposure conditions.<ref name="Quintiere-2-247" /><ref name="VR-1.7">Van Rossum (2027), §1.7.</ref>

== See also ==

* [[Euroclass system]]
* [[Travelling fire]]
* [[Trench effect]]
* [[Wildfire]]

== Notes ==

<references />

== References ==

* Australian Building Codes Board, National Research Council of Canada, International Code Council, & Department of Building and Housing New Zealand. (2005). ''International fire engineering guidelines'' (2005 ed.). Australian Building Codes Board.
* Beyler, C. L., & Hirschler, M. M. (2002). Thermal decomposition of polymers. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Drysdale, D. D. (2002). Thermochemistry. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Kanury, A. M. (2002). Flaming ignition of solid fuels. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Quintiere, J. G. (2002). Surface flame spread. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Tien, C. L., Lee, K. Y., & Stretton, A. J. (2002). Radiation heat transfer. In P. J. DiNenno (Ed.), ''SFPE handbook of fire protection engineering'' (3rd ed.). National Fire Protection Association.
* Van Rossum, E. (2027). ''Introduction to Fire Safety Engineering''. Fire Safety Academy.

[[Category:Ignition & Flame Spread]]