Firebrands - Revision history

Lisa: Add Intermediate SVG figures with Fire Safety Academy watermark at planned locations; preserve article text

2026-11-02T17:15:12Z

Add Intermediate SVG figures with Fire Safety Academy watermark at planned locations; preserve article text

← Older revision		Revision as of 18:15, 2 November 2026
Line 5:		Line 5:
	== Formation and transport ==		== Formation and transport ==
	Transport starts in the fire plume. Above an open fire, about 70% of the heat leaves by convection and about 30% by radiation, so most of the energy goes into a rising column of hot gas.<ref name="VR-5.3">Van Rossum (2027), §5.3.</ref> Convective forces in this plume lift burning brands, which fall onto combustible materials elsewhere. This lofting has been observed in warehouse fires and in wildland fires, both of which involve cellulosic materials.<ref name="HMMOA-30" /> While it rises and falls, a brand may be carried by the wind. ''Introduction to Fire Safety Engineering'' notes that wind is difficult to predict, and the International Fire Engineering Guidelines state that the travel distance of a brand rising in the plume is difficult to establish.<ref name="VR-6.6">Van Rossum (2027), §6.6.</ref><ref name="IFEG-2.6-12" />		Transport starts in the fire plume. Above an open fire, about 70% of the heat leaves by convection and about 30% by radiation, so most of the energy goes into a rising column of hot gas.<ref name="VR-5.3">Van Rossum (2027), §5.3.</ref> Convective forces in this plume lift burning brands, which fall onto combustible materials elsewhere. This lofting has been observed in warehouse fires and in wildland fires, both of which involve cellulosic materials.<ref name="HMMOA-30" /> While it rises and falls, a brand may be carried by the wind. ''Introduction to Fire Safety Engineering'' notes that wind is difficult to predict, and the International Fire Engineering Guidelines state that the travel distance of a brand rising in the plume is difficult to establish.<ref name="VR-6.6">Van Rossum (2027), §6.6.</ref><ref name="IFEG-2.6-12" />

			[[File:fse-firebrands-v1.svg\|thumb\|upright=1.5\|alt=Side view: a burning building sends a plume upward; small burning brands rise in it, drift downwind and land on a roof and on vegetation.\|Firebrands are lofted by the convective plume, carried by the wind and can ignite combustible material where they land. Based on Hamins, Maranghides, McGrattan, Ohlemiller, and Anleitner (2005), p. 30, and National Research Council of Canada et al. (2005), p. 2.6-12.]]

	Computer models treat firebrands as particles moving through the gas. In the Fire Dynamics Simulator, a solid-phase reaction can produce material that leaves the burning surface as particles, which the documentation calls a firebrand.<ref name="FDS-222">McGrattan et al. (2026), p. 222.</ref> Lagrangian particles can represent airborne vegetation such as burning brands. Each particle feels gravity and a drag force from the surrounding gas, which depends on its size, shape and speed relative to the flow.<ref name="FDS-95">McGrattan et al. (2026), pp. 95–96.</ref> Drag coefficients are given for cylindrical and for thin disk-shaped particles.<ref name="FDS-95" /> The United States Forest Service supported the development of such sub-models to simulate fire spread at the [[wildland-urban interface]].<ref name="FDS-ix">McGrattan et al. (2026), p. ix.</ref>		Computer models treat firebrands as particles moving through the gas. In the Fire Dynamics Simulator, a solid-phase reaction can produce material that leaves the burning surface as particles, which the documentation calls a firebrand.<ref name="FDS-222">McGrattan et al. (2026), p. 222.</ref> Lagrangian particles can represent airborne vegetation such as burning brands. Each particle feels gravity and a drag force from the surrounding gas, which depends on its size, shape and speed relative to the flow.<ref name="FDS-95">McGrattan et al. (2026), pp. 95–96.</ref> Drag coefficients are given for cylindrical and for thin disk-shaped particles.<ref name="FDS-95" /> The United States Forest Service supported the development of such sub-models to simulate fire spread at the [[wildland-urban interface]].<ref name="FDS-ix">McGrattan et al. (2026), p. ix.</ref>
Line 12:		Line 14:

	Ignition can take three forms. Combustion is called smouldering when it takes place within the solid below the surface, glowing when it takes place at the surface, and flaming when it takes place in the gas phase.<ref name="Kan-230" /> Because a firebrand may be smouldering rather than flaming, [[smouldering]] combustion is part of the picture.<ref name="IS-F24" /> Smouldering can turn into flaming when the supply of oxygen is increased, for example by airflow over the fuel.<ref name="Ohl-208">Ohlemiller (2002), p. 2-208.</ref> In experiments by Palmer on layers of wood sawdust, the transition occurred at airflow velocities of about 0.9 to 1.7 m/s, but only when the air moved in the same direction as the smoulder front. Ohlemiller compares this with starting a camp fire from tinder and sparks.<ref name="Ohl-208" />		Ignition can take three forms. Combustion is called smouldering when it takes place within the solid below the surface, glowing when it takes place at the surface, and flaming when it takes place in the gas phase.<ref name="Kan-230" /> Because a firebrand may be smouldering rather than flaming, [[smouldering]] combustion is part of the picture.<ref name="IS-F24" /> Smouldering can turn into flaming when the supply of oxygen is increased, for example by airflow over the fuel.<ref name="Ohl-208">Ohlemiller (2002), p. 2-208.</ref> In experiments by Palmer on layers of wood sawdust, the transition occurred at airflow velocities of about 0.9 to 1.7 m/s, but only when the air moved in the same direction as the smoulder front. Ohlemiller compares this with starting a camp fire from tinder and sparks.<ref name="Ohl-208" />

			[[File:fse-firebrands-v3.svg\|thumb\|upright=1.5\|alt=Cross-section of a fuel bed with a landed brand: smouldering zone inside, glowing surface, and a flame above once air flows over the bed.\|Smouldering, glowing and flaming combustion after a firebrand lands on a fuel bed; airflow in the direction of the smoulder front can trigger the transition to flaming. Based on Kanury (2002a), p. 2-230, and Ohlemiller (2002), p. 2-208.]]

	The time to flaming can be long. In a literature survey of smouldering in upholstered chairs and beds, about two-thirds of the items tested changed to flaming combustion, after between 22 and 306 minutes.<ref name="Ohl-208" /> Smouldering ignition can therefore take a long time to develop into a flaming fire. Glowing particles from a fire can also ignite a flammable mixture of pyrolysis gases inside a space and cause a smoke gas explosion.<ref name="VR-4.10">Van Rossum (2027), §4.10.</ref> For comparison, most materials ignite at temperatures between about 200 and 500 °C when they are heated by a hot smoke layer.<ref name="VR-9.3b">Van Rossum (2027), §9.3 (Results from zone models).</ref>		The time to flaming can be long. In a literature survey of smouldering in upholstered chairs and beds, about two-thirds of the items tested changed to flaming combustion, after between 22 and 306 minutes.<ref name="Ohl-208" /> Smouldering ignition can therefore take a long time to develop into a flaming fire. Glowing particles from a fire can also ignite a flammable mixture of pyrolysis gases inside a space and cause a smoke gas explosion.<ref name="VR-4.10">Van Rossum (2027), §4.10.</ref> For comparison, most materials ignite at temperatures between about 200 and 500 °C when they are heated by a hot smoke layer.<ref name="VR-9.3b">Van Rossum (2027), §9.3 (Results from zone models).</ref>
Line 19:		Line 23:

	In building fires, firebrands are one route of [[fire spread between buildings]]. The International Fire Engineering Guidelines list burning embers and other debris, radiation and direct flame contact as the ways in which fire can spread to an adjacent enclosure, building or property boundary.<ref name="IFEG-1.6-7" /> Depending on how a building and its contents burn, the distribution of flying brands and embers may need to be considered if fire spread to adjoining property is to be limited.<ref name="IFEG-1.6-5" /> Protection of adjacent buildings against flying brands is also listed among the objectives that fire service intervention and firefighting facilities support.<ref name="IFEG-2.9-3">National Research Council of Canada et al. (2005), p. 2.9-3.</ref>		In building fires, firebrands are one route of [[fire spread between buildings]]. The International Fire Engineering Guidelines list burning embers and other debris, radiation and direct flame contact as the ways in which fire can spread to an adjacent enclosure, building or property boundary.<ref name="IFEG-1.6-7" /> Depending on how a building and its contents burn, the distribution of flying brands and embers may need to be considered if fire spread to adjoining property is to be limited.<ref name="IFEG-1.6-5" /> Protection of adjacent buildings against flying brands is also listed among the objectives that fire service intervention and firefighting facilities support.<ref name="IFEG-2.9-3">National Research Council of Canada et al. (2005), p. 2.9-3.</ref>

			[[File:fse-firebrands-v2.svg\|thumb\|upright=1.5\|alt=Three panels with two buildings each: embers flying to the neighbour's roof, heat radiation crossing the gap, and flames touching the neighbouring wall.\|The three routes of fire spread to an adjacent building: burning embers and debris, radiation and direct flame contact. Based on National Research Council of Canada et al. (2005), p. 1.6-7.]]

	Firebrands can also be produced by a building collapse. When the North Tower of the World Trade Center collapsed in 2001, most burning material would have been extinguished. NIST considered it possible, however, that many potential ignition sources survived and were spread with the dust- and debris-laden air. These flows were many storeys tall and passed around and beyond World Trade Center 7.<ref name="McA-189">McAllister et al. (2008), p. 189.</ref> Not every fire spreads by brands: in NIST's experiments with burning office workstations, the video record showed no evidence that flying brands played a role in flame spread.<ref name="HMMOA-30" />		Firebrands can also be produced by a building collapse. When the North Tower of the World Trade Center collapsed in 2001, most burning material would have been extinguished. NIST considered it possible, however, that many potential ignition sources survived and were spread with the dust- and debris-laden air. These flows were many storeys tall and passed around and beyond World Trade Center 7.<ref name="McA-189">McAllister et al. (2008), p. 189.</ref> Not every fire spreads by brands: in NIST's experiments with burning office workstations, the video record showed no evidence that flying brands played a role in flame spread.<ref name="HMMOA-30" />
Line 26:		Line 32:

	The American roof covering standard NFPA 256 classifies roofs by the flame spread in the test. Class A allows less than 1.82 m (6 ft), class B less than 2.44 m (8 ft) and class C less than 3.96 m (13 ft).<ref name="IS-C11">Iqbal and Salley (2004), p. C-11.</ref> For all classes there may be no significant lateral flame spread and no flaming on the underside of the deck. Flying brands or particles from the roof covering may not continue to flame or glow after reaching the floor.<ref name="IS-C11" />		The American roof covering standard NFPA 256 classifies roofs by the flame spread in the test. Class A allows less than 1.82 m (6 ft), class B less than 2.44 m (8 ft) and class C less than 3.96 m (13 ft).<ref name="IS-C11">Iqbal and Salley (2004), p. C-11.</ref> For all classes there may be no significant lateral flame spread and no flaming on the underside of the deck. Flying brands or particles from the roof covering may not continue to flame or glow after reaching the floor.<ref name="IS-C11" />

			[[File:fse-firebrands-v4.svg\|thumb\|upright=1.5\|alt=Bar chart of maximum flame spread for roof covering classes: class A 1.82 m, class B 2.44 m, class C 3.96 m.\|Maximum flame spread for roof covering classes A, B and C in NFPA 256. Based on Iqbal and Salley (2004), p. C-11.]]

	== Limitations and open questions ==		== Limitations and open questions ==

Daan: New FSE wiki article: Firebrands (written by Claude Opus 5.5)

2026-11-01T22:51:53Z

New FSE wiki article: Firebrands (written by Claude Opus 5.5)

New page

'''Firebrands''' are flaming or smouldering airborne objects that emerge from a fire and can sometimes ignite combustible material at a distance from it.<ref name="IS-F24">Iqbal and Salley (2004), p. F-24.</ref> The terms flying brands, burning brands and embers are also used.<ref name="Qui-255">Quintiere (2002b), p. 2-255.</ref><ref name="IFEG-2.6-12">National Research Council of Canada et al. (2005), p. 2.6-12.</ref><ref name="HMMOA-30">Hamins, Maranghides, McGrattan, Ohlemiller, and Anleitner (2005), p. 30.</ref> An ember is a particle of solid material that emits radiant energy because of its temperature or because it is burning at its surface.<ref name="IS-F22">Iqbal and Salley (2004), p. F-22.</ref> Firebrands rise with the hot gases above a fire and can be carried by the wind before they fall onto combustible material.<ref name="HMMOA-30" /><ref name="IFEG-2.6-12" />

Burning embers and other debris are one of three ways in which fire spreads from one building or property to another, besides radiation and direct flame contact.<ref name="IFEG-1.6-7">National Research Council of Canada et al. (2005), p. 1.6-7.</ref> In forest fires, wind currents can carry large embers over great distances and start spot fires at other locations.<ref name="Qui-255" /> In areas prone to bushfires or wildfires, the spread of flying brands and embers can therefore have consequences for building design.<ref name="IFEG-1.6-5">National Research Council of Canada et al. (2005), p. 1.6-5.</ref> The distance a burning brand can travel is difficult to establish with any certainty, which makes firebrands hard to quantify in design.<ref name="IFEG-2.6-12" />

== Formation and transport ==
Transport starts in the fire plume. Above an open fire, about 70% of the heat leaves by convection and about 30% by radiation, so most of the energy goes into a rising column of hot gas.<ref name="VR-5.3">Van Rossum (2027), §5.3.</ref> Convective forces in this plume lift burning brands, which fall onto combustible materials elsewhere. This lofting has been observed in warehouse fires and in wildland fires, both of which involve cellulosic materials.<ref name="HMMOA-30" /> While it rises and falls, a brand may be carried by the wind. ''Introduction to Fire Safety Engineering'' notes that wind is difficult to predict, and the International Fire Engineering Guidelines state that the travel distance of a brand rising in the plume is difficult to establish.<ref name="VR-6.6">Van Rossum (2027), §6.6.</ref><ref name="IFEG-2.6-12" />

Computer models treat firebrands as particles moving through the gas. In the Fire Dynamics Simulator, a solid-phase reaction can produce material that leaves the burning surface as particles, which the documentation calls a firebrand.<ref name="FDS-222">McGrattan et al. (2026), p. 222.</ref> Lagrangian particles can represent airborne vegetation such as burning brands. Each particle feels gravity and a drag force from the surrounding gas, which depends on its size, shape and speed relative to the flow.<ref name="FDS-95">McGrattan et al. (2026), pp. 95–96.</ref> Drag coefficients are given for cylindrical and for thin disk-shaped particles.<ref name="FDS-95" /> The United States Forest Service supported the development of such sub-models to simulate fire spread at the [[wildland-urban interface]].<ref name="FDS-ix">McGrattan et al. (2026), p. ix.</ref>

== Ignition by firebrands ==
A firebrand starts a new fire when it lands on a receptive fuel and causes [[ignition]]. A glowing brand can act as a pilot source. Piloted ignition is ignition in the presence of a small flame, a heated wire, an electric spark or an incandescent particle, as opposed to spontaneous ignition without such a source.<ref name="Kan-230">Kanury (2002a), p. 2-230.</ref><ref name="Kan-232">Kanury (2002a), p. 2-232.</ref> The pilot source is usually so small that its contribution to heating the solid can be ignored. Its role is to start combustion in a flammable mixture of fuel gases and air near the surface.<ref name="Kan-232" />

Ignition can take three forms. Combustion is called smouldering when it takes place within the solid below the surface, glowing when it takes place at the surface, and flaming when it takes place in the gas phase.<ref name="Kan-230" /> Because a firebrand may be smouldering rather than flaming, [[smouldering]] combustion is part of the picture.<ref name="IS-F24" /> Smouldering can turn into flaming when the supply of oxygen is increased, for example by airflow over the fuel.<ref name="Ohl-208">Ohlemiller (2002), p. 2-208.</ref> In experiments by Palmer on layers of wood sawdust, the transition occurred at airflow velocities of about 0.9 to 1.7 m/s, but only when the air moved in the same direction as the smoulder front. Ohlemiller compares this with starting a camp fire from tinder and sparks.<ref name="Ohl-208" />

The time to flaming can be long. In a literature survey of smouldering in upholstered chairs and beds, about two-thirds of the items tested changed to flaming combustion, after between 22 and 306 minutes.<ref name="Ohl-208" /> Smouldering ignition can therefore take a long time to develop into a flaming fire. Glowing particles from a fire can also ignite a flammable mixture of pyrolysis gases inside a space and cause a smoke gas explosion.<ref name="VR-4.10">Van Rossum (2027), §4.10.</ref> For comparison, most materials ignite at temperatures between about 200 and 500 °C when they are heated by a hot smoke layer.<ref name="VR-9.3b">Van Rossum (2027), §9.3 (Results from zone models).</ref>

== Firebrands in wildfires and building fires ==
In a [[wildfire]] in a forest, flame spread depends on radiant heat transfer and on convective heating by wind or by the slope of the terrain. In severe fires the crowns of the trees also burn.<ref name="Qui-255" /> Wind currents can then carry large embers great distances from the fire, where they start spot fires. Breaks in the fuel can be used to control the spread, but the break needed to interrupt the fire depends on the size of the fire and its heat transfer.<ref name="Qui-255" />

In building fires, firebrands are one route of [[fire spread between buildings]]. The International Fire Engineering Guidelines list burning embers and other debris, radiation and direct flame contact as the ways in which fire can spread to an adjacent enclosure, building or property boundary.<ref name="IFEG-1.6-7" /> Depending on how a building and its contents burn, the distribution of flying brands and embers may need to be considered if fire spread to adjoining property is to be limited.<ref name="IFEG-1.6-5" /> Protection of adjacent buildings against flying brands is also listed among the objectives that fire service intervention and firefighting facilities support.<ref name="IFEG-2.9-3">National Research Council of Canada et al. (2005), p. 2.9-3.</ref>

Firebrands can also be produced by a building collapse. When the North Tower of the World Trade Center collapsed in 2001, most burning material would have been extinguished. NIST considered it possible, however, that many potential ignition sources survived and were spread with the dust- and debris-laden air. These flows were many storeys tall and passed around and beyond World Trade Center 7.<ref name="McA-189">McAllister et al. (2008), p. 189.</ref> Not every fire spreads by brands: in NIST's experiments with burning office workstations, the video record showed no evidence that flying brands played a role in flame spread.<ref name="HMMOA-30" />

== Roofs and testing ==
Several test standards expose roof coverings to brands. British Standard BS 476 Part 3 describes a test of the ignitability and fire spread of external roof surfaces. It exposes the roof to radiation from a fire in an adjacent building and to piloted ignition from flying brands.<ref name="IFEG-2.6-12" /> In the United States, the roof covering tests ASTM E108 and UL 790 include a burning brand test and a flying brand test besides tests for flame spread and intermittent flame.<ref name="IS-C12">Iqbal and Salley (2004), p. C-12.</ref>

The American roof covering standard NFPA 256 classifies roofs by the flame spread in the test. Class A allows less than 1.82 m (6 ft), class B less than 2.44 m (8 ft) and class C less than 3.96 m (13 ft).<ref name="IS-C11">Iqbal and Salley (2004), p. C-11.</ref> For all classes there may be no significant lateral flame spread and no flaming on the underside of the deck. Flying brands or particles from the roof covering may not continue to flame or glow after reaching the floor.<ref name="IS-C11" />

== Limitations and open questions ==
The fire safety engineering documents used for this article treat firebrands only briefly. They define the phenomenon, describe how brands are lofted and carried, and name roof tests and design considerations, but give no measured data on brand sizes, numbers or travel distances.<ref name="IFEG-2.6-12" /><ref name="IS-F24" /> The International Fire Engineering Guidelines state plainly that the distance a burning brand may be carried cannot be established with any certainty.<ref name="IFEG-2.6-12" /> In these sources, firebrand exposure is addressed through roof covering tests and design considerations for bushfire-prone areas rather than through calculation methods.<ref name="IFEG-1.6-5" /><ref name="IS-C11" />

Numerical models can follow individual brands as particles, but their results depend on the assumed shape, size and drag of each particle and on the wind field.<ref name="FDS-95" /> Whether a smouldering brand leads to flaming also depends on the airflow over the fuel.<ref name="Ohl-208" /> Firebrands are not limited to forest fires. The same mechanism has been observed in warehouse fires, and it is one of the routes by which fire spreads between buildings.<ref name="HMMOA-30" /><ref name="IFEG-1.6-7" />

== See also ==
* [[Fire spread]]
* [[Facade fire]]
* [[Warehouse fire]]

== Notes ==
<references />

== References ==
* Hamins, A., Maranghides, A., McGrattan, K. B., Ohlemiller, T. J., & Anleitner, R. L. (2005). ''Experiments and modeling of multiple workstations burning in a compartment'' (NIST NCSTAR 1-5E). National Institute of Standards and Technology.
* Iqbal, N., & Salley, M. H. (2004). ''Fire Dynamics Tools (FDTs): Quantitative fire hazard analysis methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program'' (NUREG-1805). U.S. Nuclear Regulatory Commission, Office of Nuclear Reactor Regulation.
* Kanury, A. M. (2002a). Flaming ignition of solid fuels. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), ''SFPE handbook of fire protection engineering'' (3rd ed., pp. 2-229–2-245). National Fire Protection Association; Society of Fire Protection Engineers.
* McAllister, T. P., Gann, R. G., Averill, J. D., Gross, J. L., Grosshandler, W. L., Lawson, J. R., McGrattan, K. B., Pitts, W. M., Prasad, K. R., Sadek, F. H., & Nelson, H. E. (2008). ''Structural fire response and probable collapse sequence of World Trade Center Building 7'' (NIST NCSTAR 1-9, Vols. 1–2). National Institute of Standards and Technology.
* McGrattan, K., Hostikka, S., Floyd, J., McDermott, R., Vanella, M., Mueller, E., & Paul, C. (2026). ''Fire Dynamics Simulator technical reference guide: Vol. 1. Mathematical model'' (6th ed., NIST Special Publication 1018-1). National Institute of Standards and Technology. https://doi.org/10.6028/NIST.SP.1018
* National Research Council of Canada, International Code Council, Department of Building and Housing, & Australian Building Codes Board. (2005). ''International fire engineering guidelines'' (2005 ed.). Australian Building Codes Board.
* Ohlemiller, T. J. (2002). Smoldering combustion. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), ''SFPE handbook of fire protection engineering'' (3rd ed., pp. 2-200–2-210). National Fire Protection Association; Society of Fire Protection Engineers.
* Quintiere, J. G. (2002b). Surface flame spread. In P. J. DiNenno, D. Drysdale, C. L. Beyler, W. D. Walton, R. L. P. Custer, J. R. Hall Jr., & J. M. Watts Jr. (Eds.), ''SFPE handbook of fire protection engineering'' (3rd ed., pp. 2-246–2-257). National Fire Protection Association; Society of Fire Protection Engineers.
* Van Rossum, E. (2027). ''Introduction to Fire Safety Engineering''. Fire Safety Academy.

[[Category:Special Hazards & Building Types]]